I appreciate being able to see the procedure before I dig into it. I'm a auto mechanic and certificated aircraft mechanic so I appreciate watching you and your boy working on the car, start'em young to be self sufficient! Even I have discovered a loose bolt until I go over it again.
@09fatbobmike
10 ай бұрын
pull that e brake cable.. The reason it becomes hard to pull out and the reason the hub will not lean forward anymore is the e-brake cable. and the reason for terrible uneven tread wear is the wheel spacers.
@sumcrazydude
10 ай бұрын
Thank you captain obviousness, I would have never figured without you.
@undergod9586
3 жыл бұрын
Great video brotha. Well put together and very informative. It's even better because you had you son working and learning with you...😎👌🏾🔥🔥🔥
@sumcrazydude
3 жыл бұрын
Awesome, thank you so much!!
@undergod9586
3 жыл бұрын
@@sumcrazydude No problem Merry Christmas 🎄🎁😎
@sumcrazydude
3 жыл бұрын
Thanks and a Merry Christmas to you as well
@BAdbOY_SRT8
2 жыл бұрын
Watched your vid thought it was gonna be easy like how you did, mines 09 300c srt8 and found out axels are thicker and don't flex too well on the cv joint, after a freekin struggle I found it was easier to drop the suspension arm, leave on bottom bolt connecting hub assembly to suspension arm and take off everything else, all thanks to your vid bro, hope you still rocking a Hemi
@sumcrazydude
2 жыл бұрын
U know it!! I appreciate the support and I am glad to hear that my video helped you. Yes I still have a Hemi, I have 2017 Charger Pursuit AWD V8
@ceavalencia4767
Жыл бұрын
Good vid. Sweet ride. My father has a red Challenger Scat, I never really looked at them too much until I purchased my Charger Scat, but this one is really good on the eyes
@sumcrazydude
Жыл бұрын
Thanks
@jeremyt8189
8 ай бұрын
Lots of great tips. Great video funny as heck. Especially the ex files. Thanks for your time
@sumcrazydude
8 ай бұрын
Thanks 🇺🇸
@312ark
2 жыл бұрын
I knew there had to be another way other than removing the rear differential. Thanks for sharing.
@sumcrazydude
2 жыл бұрын
Awesome thanks for your support 👍 😀
@loyalty3443
Жыл бұрын
is this an all wheel drive?
@johnwargo2590
3 жыл бұрын
At 5:55 (Hub Nut removal) next time, put another floor jack under the lower control arm (slight pressure) and it'll come off easier. Nice trick with the sway bar. Enjoy working with your son while it lasts.
@sumcrazydude
3 жыл бұрын
Thanks
@dondale68
3 жыл бұрын
Took you 2 hours, But how much in ''Labor Costs'' did you save yourself?
@chrishemi5629
4 жыл бұрын
Thanks for making the video man! I did a diff swap on my 15 charger rt(upgraded to a scat pack lsd diff) and my right side is leaking oil, think i didnt get the axle to seat all the way in. Thanks again ima do this just to get my axle to go all the way in.
@sumcrazydude
4 жыл бұрын
Thank you for the support
@mikehoogendoorn7559
11 ай бұрын
Helpful! Thank You! And not looking forward to doing this right now 😂
@sumcrazydude
11 ай бұрын
Thanks for the view, make sure hydrated before doing this as it will drain you lol
@mrcjkul
2 жыл бұрын
You make it look easy I need to look at my 300s hopefully it's just bearing/hub replacing
@sumcrazydude
Жыл бұрын
Thanks but is not easy, it takes patience 🙂
@andrewivanowich8390
2 жыл бұрын
I'm thinking if you put the jack under the control arm then pulled out the shock bolt and lowered the jack you could do it without prying. Alot easier than dropping the diff like the pros say.
@sumcrazydude
Жыл бұрын
True that
@sumcrazydude
Жыл бұрын
@SÍLAS_5.7 what?
@davidbutler5825
2 жыл бұрын
Great real video showing actually truth thanks for information 👍
@sergioca1208
2 жыл бұрын
Thank you for sharing your expertise and knowledge. Really appreciate it. My oil seals on these axels are leaking. Can you do a video on how to replace them? Or, can you provide some tips?
@sumcrazydude
2 жыл бұрын
Sadly I no longer own this car. But thanks for your support 😀
@Ac3Mustang
2 жыл бұрын
@@sumcrazydude did you trade it in?
@sumcrazydude
2 жыл бұрын
@@Ac3Mustang yes
@jeremyt8189
8 ай бұрын
@@sumcrazydudefor a ford? 😂
@tylermyles3867
2 жыл бұрын
Great video 👍🏽 lots of information
@sumcrazydude
2 жыл бұрын
Thanks for the support 😀
@cam2xx688
21 күн бұрын
What size is the axle nut
@kendoug5722
3 жыл бұрын
Do you think taking the shocks would make it easier?
@sumcrazydude
3 жыл бұрын
It could but I didn't tried that
@kinzieconrad105
Жыл бұрын
I don’t have a challenger but I am build a 56chev with that diff and I have the driver side axle rusted up and seized to the knuckle! At this point thinking easier to snatch a replacement assembly out of a junk yard. Less work.
@sumcrazydude
Жыл бұрын
You must be trying to restomod or track build 🤔. Nice BTW I would love to see it one day.
@whoisrobzilla
10 ай бұрын
How was the orielly replacement quality, how long did it last? Masterpro or precision?
@sumcrazydude
10 ай бұрын
This was done so long time ago I do not remember but I do remember that if your car is lowered, it will tear up the grease boot.
@marty303
2 жыл бұрын
My rear cv axle boot is leaking grease, it’s the boot that’s connected to the diff, can this ruin my transmission and diff ?
@sumcrazydude
2 жыл бұрын
If the grease is leaking from the boot of the axle itself, this will only affect the longevity of the axle and nothing else.
@marty303
2 жыл бұрын
@@sumcrazydude gotcha thanks for responding !
@sumcrazydude
2 жыл бұрын
Thanks for the support 🙏
@ChrisSglimbeaelectricfingers
Жыл бұрын
Also was that cv a 32 spline cv i think is same as for srt8 charger 2014!!! Not sure tho ! Post cv link if u can ty much vid was super nice nd job was super clean too👍🏼😊
@sumcrazydude
Жыл бұрын
Thanks for the support, I don't have a link for the cv sorry
@ChrisSglimbeaelectricfingers
Жыл бұрын
@@sumcrazydude ok may b pn nd or do u inw if is a 32 spline cv
@jeremyt8189
8 ай бұрын
Ready to go
@georgegautier372
Жыл бұрын
I need to replace a ring in one on my axles. Cause ABS sensor is killing me and don't get fixed for replace it. This ring is replaceable? or need change the whole axle?
@sumcrazydude
Жыл бұрын
Ring is replaceable if you get an undamaged one to install.
@georgegautier372
Жыл бұрын
@@sumcrazydude Thanks brother, I couldn't find de ring at any store so I bought the whole axle. Now I'm looking for dismantle all there for replace it. Dont even the dealer have those rings only online and I wasn't sure if they fit
@itzasrt
3 жыл бұрын
Very helpful 👌
@sumcrazydude
3 жыл бұрын
Thanks 😊
@kathleenterrazas
2 жыл бұрын
I have a 2012 dodge charger rt, that vibrates when accelerating, breaking, and backing up. Any idea if it's associated with cv joints or drive shaft?
@sumcrazydude
2 жыл бұрын
It's probably your driveshaft center carrying bearing, the rubber around it gave up
@jbjb275
2 жыл бұрын
Warped rotors will make it shake when braking also...
@Boosted5.7
2 жыл бұрын
I have this clicking noise coming from the rear driver side wheel-well area. Clicks when I put it in gear or reverse from idle. Also clicks as I brake or accelerate from a dead stop. Yall think it's the CV axle? 2015 5.7L 89K miles
@sumcrazydude
2 жыл бұрын
Sounds like a bad CV axle, mine sounded same before it broke
@Boosted5.7
2 жыл бұрын
@@sumcrazydude I thought so too. I need to get that fixed before I install this procharger I got sitting in the garage past month lol appreciate the video brotha!!!
@demario4887
3 жыл бұрын
Did you replace the oil that leaked out if so with weekday and how?
@sumcrazydude
3 жыл бұрын
I did but didn't recorded it, I am sure there a few video out there that explain how 😁
@miguelangelcazales3120
2 жыл бұрын
is it common for challengers to have the left rear axle to go out?? like making clicking noises and such?
@miguelangelcazales3120
2 жыл бұрын
been having the issue, and replacing the axle soon
@sumcrazydude
2 жыл бұрын
Seems that way
@miguelangelcazales3120
2 жыл бұрын
@@sumcrazydude is that the reason you replaced yours?
@sumcrazydude
2 жыл бұрын
@@miguelangelcazales3120 I replaced mine because it broke, before broke it made clicking noises
@International-BlackMan
2 жыл бұрын
Good stuff
@sumcrazydude
2 жыл бұрын
Thanks for the support 🙏 🙌
@jcasey460
3 жыл бұрын
Hi HEMI Addicted...was there any C-Clips on the axle at the hub? Was this a limited slip diff?
@sumcrazydude
3 жыл бұрын
No, inside the diff at end of the CV axle is a CV joint lock ring witch it should unlock with enough pull force when removing the axle. Yes my Challenger had a LSD .
@jcasey460
3 жыл бұрын
@@sumcrazydude Thanks...same as front axle on my Toytota 4-WD pickup. Was that tire wear from burnouts or rear alignment issue?
@sumcrazydude
3 жыл бұрын
Burnouts 😅
@jcasey460
3 жыл бұрын
@@sumcrazydude Do you use any traction control/electronic stability control when you do them
@sumcrazydude
3 жыл бұрын
No, I would normally turned everything off
@dodgerboy8327
3 жыл бұрын
What type of grease did you use for this? Did you do anything about the ABS sensor?
@sumcrazydude
3 жыл бұрын
Did not used any grease and I replaced the sensors. 😁
@silas_5.776
Жыл бұрын
@@sumcrazydude currently trying it right now but the ring part will not budge we bought a axel remover and still no budge
@sumcrazydude
Жыл бұрын
@@silas_5.776 rotate, wiggle and pry
@DreGoated
2 жыл бұрын
Hey do you have the link to we’re you purchased that axel of oreily ? I’ve been looking everywhere for one
@sumcrazydude
2 жыл бұрын
Buy the hellcat one, that's the one I bought
@DreGoated
2 жыл бұрын
Ok I’ve been told that it has to be the one for the 5.7 so that’s not true the 6.2 will fit fine ?
@sumcrazydude
2 жыл бұрын
@@DreGoated mind the fact that my car was a 2015 and I bought a 2015 hellcat axle. What I found out was that if you lower the car the axle may pop out cause it's slightly shorter than a 5.7 axle
@DreGoated
2 жыл бұрын
@@sumcrazydude ohh ok last question so if I’m not lowered would it be possible I could still go with a hellcat axle ?
@sumcrazydude
2 жыл бұрын
I don't see why not.
@platesandbricks799
3 жыл бұрын
Was it making clinking noises when it broke...
@sumcrazydude
3 жыл бұрын
Yup during turns but the ball cage never broke, the shaft is what broke
@jess...b..1894
2 ай бұрын
Great job brother 👏
@victorvela3326
3 жыл бұрын
How did you remove the locking clip
@sumcrazydude
3 жыл бұрын
There is no need to remove the locking clip.
@lll_0_w_ll148
4 жыл бұрын
Where did you find the axle ! I been looking for a new one for the past month and I haven’t found any I need help
@sumcrazydude
4 жыл бұрын
O'Reilly Auto Parts my friend, they have em cheap and good 👍
@lll_0_w_ll148
4 жыл бұрын
Wait what !? Really do you have the part number or item number !
What is the axle part number and spline? Im having trouble getting the correct axle from oreilly
@sumcrazydude
3 жыл бұрын
I don't know what car you have
@shanelayfield1227
3 жыл бұрын
Mine is a 2009 with a getrag upgrade. I found the mopar axle number today. No aftermarket available thats the correct spline
@sumcrazydude
3 жыл бұрын
I used a hellcat axle pn so I don't know how can that help you since my car was a 2015
@shanelayfield1227
3 жыл бұрын
@@sumcrazydude mine has a 2015 rear center section. I ordered 35 spline hubs so I think tge axle you used will work on mine now
@shanelayfield1227
3 жыл бұрын
Mine has a 32 spline at the rearend is that the same as yours?
@ericmoralezz
3 жыл бұрын
So far how are they treating you any issues?
@sumcrazydude
3 жыл бұрын
They were great, no issues after this one was installed. I don't have the car anymore so I don't really know if any changes.
@ericmoralezz
3 жыл бұрын
Thanks for the imput man ..one more things did you have to transfer any seal from the old to new ones?
@sumcrazydude
3 жыл бұрын
Nope
@ericmoralezz
3 жыл бұрын
Hey sir srry i know you dnt have the chally no more lol but how did u remove the c clips from the axles u just pryd it out or tapped the axle to shake it off?
@AWESOMELawsonDIY
3 жыл бұрын
What size socket did you use for the axle nut?
@sumcrazydude
3 жыл бұрын
That I do not remember, I rented a axle nut socket set from the auto parts store
@AWESOMELawsonDIY
3 жыл бұрын
Ok thank you anyways. Very informative video by the way gave me confidence to do the job myself. It took me a few months to finally find out what that terrible noise was in the rear of my challenger. How many times have you had to change your rear cv axles?
@sumcrazydude
3 жыл бұрын
2 times 😅
@beeotto8710
Жыл бұрын
I need to bring my car to you!! My tires wear out on the inside & i end up having to buy tires every 2-3 weeks. I need your number 😢
@sumcrazydude
Жыл бұрын
Lol, how does replacing an axle will fix your tires?
@beeotto8710
Жыл бұрын
I should of been more in depth lol i took it to a guy who told me it was my axle that’s bent/broken.. the same issue you noticed when your son took off your wheel, is the same thing that happens to my dodge charger when i catch a flat. I mean your the mechanic here.. so i was really looking for some guidance but ok ill find help elsewhere, geesh
@Eben18
3 жыл бұрын
Did you have the vehicle lowered?
@sumcrazydude
3 жыл бұрын
Yes, it is 😁
@Eben18
3 жыл бұрын
@@sumcrazydude I commented before the end of the video. Amazing video I am having an issue with premature wear too and I will need to replace my drive axle too. Any recommendations you did not show on the video?
@sumcrazydude
3 жыл бұрын
Just to take the lower control arm bolt out, it will make it easier for you
@Eben18
3 жыл бұрын
@@sumcrazydude Do not take out the middle bolt right above?
@sumcrazydude
3 жыл бұрын
Yes, remove everything i said to remove plus the bottom control arm bolt too
@mikesmobilemecanic9572
3 жыл бұрын
My friend is getting inside wear on the rear tires... just like at the beginning of the video... what could be some issues? At 2:38
@sumcrazydude
3 жыл бұрын
Wheel alignment is key. For a sample on my car, my car was lowered and it made it have camber and toe, I liked the camber the way it is but the toe was the tire killer and it could not be fix with OEM parts. There is aftermarket products out there than can help you get best alignment to prevent fast tire wear.
@AlfredoHernandez-xr4dx
2 жыл бұрын
I always use my wife to grab my axle and put it in the hole.
@Mroswaldo16
2 жыл бұрын
Those welds lol
@sumcrazydude
2 жыл бұрын
Lol
@TeW33zy
Жыл бұрын
Bro wtf? You didn’t even grease the axel spline inside of the differential. You also didnt use a new axel bolt when u change a CV axel joint. U also forgot to torque those bolts. This why I don’t do back yard mechanics. As a Sr Quality Engineer it is very important to have someone smarter than you or as smart as you go over the axel, differential, bolts, damage inspection, loose bolts, missing bolts etc.
@sumcrazydude
Жыл бұрын
U care too much, it's a car, not a rocket.
@Ottonic6
2 ай бұрын
@TeW33zy - Wrong choice of words. He's just enjoying the day with his son and sharing it with us. No one is being forced to watch the video. I watched it to get an idea of how to approach the job, not for step by step tutorial for an ASE test. I got what I was looking for, and I thank him for that
@ichigonubetube
8 ай бұрын
Goes to show its not just mustangs. 😂 High hp rwd cars, and goof balls driving them. Mustangs are just super popular so you see it more often.
@kendoug5722
3 жыл бұрын
Air tools could’ve been handy for this job
@sumcrazydude
2 жыл бұрын
Yes but I am broke broke lol
@angmunozable
2 жыл бұрын
I use electric tools for everything
@loyalty3443
Жыл бұрын
@@sumcrazydude is this an all wheel drive or rear wheel drive?
@sumcrazydude
Жыл бұрын
@Loyalty this is a Challenger R/T they only come in RWD. I did made a video on replacing the front axles on my Current Charger that is AWD.
@eshanmostofa2391
6 ай бұрын
hey brother I had a t bone collision my rear wheel got inside a lil bit can I have your email so that I can shoot you a video need help asap
Пікірлер: 150