Thanks for watching. Please Like and Subscribe for more Money Saving tips here: kzitem.info/rock/BiVXDIBk3rCgyH4ssrH86g Here is a handy tool I use to remove the bucket. amzn.to/3wxKoNe
@HondaSnowblowerEnthusiasts311
11 ай бұрын
This is done in REAL TIME to show you that it is not too difficult if you follow step by step. KZitem put a time limit on this video so this is 2 parts. The second part is about 7 minutes long. You can find the PART 2 of this at end of this video or check our channel playlist. Thanks for watching.
@franksanders1000
18 күн бұрын
Very helpful video
@HondaSnowblowerEnthusiasts311
18 күн бұрын
thanks for watching
@davidschoss1801
8 ай бұрын
Would you happen to have an auger housing for an HS624
@HondaSnowblowerEnthusiasts311
8 ай бұрын
check on facebook group Honda Snowblower Enthusiasts. thanks.
@ecwilliams777
7 ай бұрын
Great video. Quick question, were you pulling the starting cord to get the drive belt on? I saw you pulling something but it wasn't in frame of the camera so i didn't see exactly what it was. Thank you for the video, I'm going to change my drive belt tomorrow
@HondaSnowblowerEnthusiasts311
7 ай бұрын
remove spark plug wire before pulling on recoil to help thread the belt on. thanks.
@ecwilliams777
7 ай бұрын
@@HondaSnowblowerEnthusiasts311 will do. And just to be clear it was the starter cord that you were pulling? Your video saved me from having to take it to the shop so many thanks for that
@merleschmidt5810
8 ай бұрын
I have a specific question about the carbs on my hs 724 that I can't figure out. Would you be ok if I ask you some questions aboit it
@HondaSnowblowerEnthusiasts311
8 ай бұрын
please ask on Facebook group Honda Snowblower Enthusiasts. 4000 members and many good ppl that can help. thanks.
@merleschmidt5810
8 ай бұрын
Shoot I don't doo FB
@HondaSnowblowerEnthusiasts311
8 ай бұрын
with 10, 800 members/subscribers i can not always answer one on one. hope you understand.@@merleschmidt5810
@minouchat
10 ай бұрын
thank you very much
@mikejohnson1228
10 ай бұрын
Hi all, I'm in this exact process with my HS724 and was wondering, when putting the chute back on (mine is full electric, so almost a must to remove as its easier than disconnecting cable) but after the white plastic bushing is cleaned off, of old crud, do you need to put a thin layer of low temp grease on the white plastic again so it slides as the chute rotates, OR leave it dry as thats its purpose?
@HondaSnowblowerEnthusiasts311
10 ай бұрын
please post this on Facebook group. Unfortunately I do not have any experience with these electric chutes.....yet.
@floppyebrokent8578
10 ай бұрын
Thanks! Great how to. The red locktite makes me nervous, but hey, im not taking them out 😂
@HondaSnowblowerEnthusiasts311
10 ай бұрын
you can use blue. i only have red on hand but have never had a problem taking them out. have to use a breaker bar though, haha but they aint coming loose. thanks.
@missin80
9 ай бұрын
Thank you for the tip on the breaker bar😅
@HondaSnowblowerEnthusiasts311
8 ай бұрын
It's an amazing tool for any mechanic. Thanks for watching.
Пікірлер: 21