Hola soy de Mexico ,subo el trim y lo bajo funciona bien pero si lo subo hasta el limte arriba se emieza a bajar despacio, pero si le doy un toque despacio hacia abjo ya no se baja ?
@felipezafani
4 ай бұрын
Muito obrigado pelo seu comentario.
@ShaneTeague-u7n
2 ай бұрын
I just put a new one on and it's louder now is than common?
@felipezafani
2 ай бұрын
I am not sure, I assume you have filled the oil right ?
@terrybelanger8267
24 күн бұрын
@@felipezafani Hi, what is the part # ?
@eagle5720
Жыл бұрын
The system is self bleed, to make it easy all you need to do is remove the entire thing and those oring need to be change also.
@felipezafani
Жыл бұрын
I did not knew that, thanks for letting me know.
@HowardUduun
Жыл бұрын
Great video, having the same issue. removed my motor but haven't tried to clean it yet. Have you been able to find a replacement motor? I cannot seem to find the same motor ..hopefully cleaning works.
@felipezafani
Жыл бұрын
Hello, I was able to find a 3rd party motor that would definitely work, but in the end of the day I did not need to buy a motor because after cleaning the motor it worked great, I already tested and it is running perfectly, I know it is a long video but watch it and you will see. I also could not find the original volvo penta motor.
@HowardUduun
Жыл бұрын
@@felipezafani Thank you, hoping cleaning will do the trick. Would you happen to have a link to the 3rd party motor you found in case i need to replace it? I ordered one but upon further inspection it looks like the shaft is different, even though it says for all Volvo Pentas.
@JoelTeichman
2 ай бұрын
@@HowardUduundid you ever find a replacement motor? If so do you have a part number?
@JoelTeichman
2 ай бұрын
Has anyone found a replacement motor and if so do you have a part number?
@felipezafani
2 ай бұрын
I’ll look for it. I don’t recall the part number since I was able to fix the
@eagle5720
Жыл бұрын
dude you need to get rebuild kit for that thing else all those gasket and o ring going to be leaking internally which going cause the drive to either not go up or creep back down by it self because it may loose pressure.
@felipezafani
Жыл бұрын
I agree but I could not find the repair seals for sale. Have you found it ?
@aceofalltrades5425
6 ай бұрын
Thanks for the video it was helpful but my motor is fried do you have a link for a replacement motor I can’t seem to find one anywhere
@felipezafani
6 ай бұрын
There is a non original motor at Amazon that I was going to buy not sure if it is a direct fit! Volvo only sells the full assembly as far as I know and it is very expensive.
@luiselizarraras4932
5 ай бұрын
Hi, I'm from Mexico. I raise the trim and lower it, it works fine, but if I raise it to the upper limit, it starts to go down slowly, but if I give it a slow touch down, it doesn't go down anymore. Could it be that I already changed the plastic washers?
@felipezafani
4 ай бұрын
Could be or the fluid level is low, check the fluid level on the hydraulic pump, it could be the reason it is going down low
@WheelinWithAustin
3 ай бұрын
Man thank you for the video and your knowledge!
@felipezafani
3 ай бұрын
Any time! Glad it helped you. Just sharing what I learned.
@rickmoser6751
Жыл бұрын
Great video! I have the exact same boat and I hear my motor running but it still doesn't trim. I will remove the motor and see if an o ring has failed or whatever. I'm more confident now to tear into it because of your shared video.
@felipezafani
Жыл бұрын
Glad it helped, thanks for sharing with me. It is good when a video can somehow help. It may need oil or you could have a gasket / o ring failed. You also may need to bleed the line, I mean remove any air in the lines and pistons.
Пікірлер: 23