Bro definitely took thee longest route now you need a whole alignment leave everything on remove the axle nut , remove tierod end , remove upper control arm bolt from spindle & strut remove axel 👌
@ezkoshows7136
3 ай бұрын
You would still need an alignment with your steps, all he did extra was take off the bolt for the lower control arm
@kushacres2362
Жыл бұрын
Bro I needed this vid a month ago... I ended up struggling since it was my first time doing this but now its ezz
@ariette.vr30
4 ай бұрын
Just did mine thanks for the video bro deadass helped.. BUT you know what killed me the most was budging the damn axle out with a pry bar.. didn’t have the one you had in the video and it would not budge ! Once I copped the one you had from harbor freight for 7 beans .. that shit came out in like 5 seconds so I would definitely say that L shaped pry bar is a MUST
@Daniel-kp8pe
Жыл бұрын
i got a g37 i need lower control outer tie rods and driver axle you think i should go all oem or go aftermarket im in NYC my axle just have a slight rip
@fullpeladas
11 ай бұрын
Great instructional video that's awd ? That g37 needs lots of work
@antoniojuarez5247
Ай бұрын
Do this have a bearing on the back of the axle seal? Mine has a lot of play
@Kocaineee
11 ай бұрын
Is this the same removal procedure as the X awd version? Nice video
@ericmarciniak1
11 ай бұрын
yes because the rwd doesn't have front cv's haha
@Kocaineee
11 ай бұрын
@@ericmarciniak1 right 😭😭😭😭😭 my dumbass 😂😂😂 thank you bro
@panixfn9066
Жыл бұрын
what impact do you use? or do you recommend for jobs like this?
@JulesMechanics
Жыл бұрын
Dewalt
@OleBoyy15
2 ай бұрын
How the hell did you get the CV axle through the fork at the end of the coil over? Mine will not fit through and if I try to pry it down and farther the shock is going to pop out of the brace
@ijostin5143
10 ай бұрын
I have g37x coupe 2012 i can’t find the part to buy
@dave3952
11 ай бұрын
Thanks for the video. I have to do the same on my 11 G37xS.
@nolson8851
5 ай бұрын
Did you add more fluid that came out after taking the axle off? If so, how?
@urygen
5 ай бұрын
Some will be lost. There’s drain and fill plugs on the front diff. Make sure u can remove fill plug before attempting lower drain plug
@danellebarnette6380
10 ай бұрын
Did the axle not need a seal or gasket for the differential side for half axle?
@JulesMechanics
10 ай бұрын
No seal was good
@kushacres2362
Жыл бұрын
W vid bro
@mikeyy425
10 ай бұрын
I just put one in, but after putting the hub back on. The wheel/axel doesn’t spin as freely as before. Have to put a lot of pressure to turn the wheel/axle. Doesn’t seem right, the other axle (driver side) still spins freely when i jack it up. What should i do?
@camfreeman5911
8 ай бұрын
did you get it fixed? having same issue
@mikeyy425
8 ай бұрын
@@camfreeman5911 i had no choice but to drive it. Was worried it could damage the transmission. The drive felt weird at first, like there was resistance (car slows a lot quicker when not accelerating). But its been a month or so and haven’t had any problems or noticed any tranny issues (transitioning into sport, eco or snow is fine). Hopefully that was a normal thing.
@Ikemag
10 ай бұрын
Do you need a special tool to put the axle in?
@JulesMechanics
10 ай бұрын
NO
@kevinpaul6640
Жыл бұрын
W vid
@JoJo-sw9yz
8 ай бұрын
Bro my g37x makes a screeching noise when I’m accelerating and Turning at the same time. Also When I turn my steering wheel and let off the gas and letting it role my car will coke to a stop and I’ll have to give it a little gas to go and then it’ll make clinking noises like a bind
Пікірлер: 28