√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*
@orionsimerl6539
Жыл бұрын
This is not the video you want to follow. There's no need to take off the tie rod end or the knuckle.
@dave6032
2 ай бұрын
Precise and to the point… excellent video… thanks
@Ken-1
3 жыл бұрын
Is this like a 1A Auto spinoff channel/brand? Dude, I recognize your voice anywhere haha, great work as always though!
@SyeberDash
2 ай бұрын
It’s TRQ it’s the brand of the parts which 1AAUTO sells
@venomrogue1
7 ай бұрын
I don’t like leaving just the lower ball joint connected. Great way damage it. Not required to remove strut bolts to do this job.
@tetris3289
Жыл бұрын
Wtf why did u take the knuckle out? U had enough room to take the bearing out without it.
@Jayyak47
Жыл бұрын
I found taking the knucke off to be helpful i couldnt reach the hub bolts with my impact wrench
@ChrisShipley-ec5qz
5 ай бұрын
Question can ur wheel come off riding on bad wheel bearings?
@ivanperez-so4bx
7 ай бұрын
No buddy, you don't need take off all these parts to reemplace the bearing hub, you wrong definitely !
@michealmiller6630
Жыл бұрын
Just give it a couple loving bonks!!
@brianmccabe881
2 ай бұрын
How long should this take?
@alanbrooks3670
3 жыл бұрын
Great step by step guide with all the info for torque specs and bolt size and you make it look easy but after installing should you have to get a alignment you did change the tie rod end wouldn't it possibly change the toe in and with un bolting the struts the camber may be off? Or is that adjusted another way
@annaperez7383
3 жыл бұрын
Any info on the front passenger sliders and where they would go plunger side top or bottom?
@DevJB
Жыл бұрын
The top guide pin is metal. The lock pin (lower) has a plastic ubber anti-rattle tip. The lock pin is a few thousands smaller than the solid metal guide pin. Lock pins go on the lower or front most hole toward front of vehicle. Imagine car is rolling forward and hits the brakes, the force of the calipers go downward and forward. We want this lock pin to be on the lower forward spot of the down force. This lock pin rubber sleeve comes in a boot kit and should be replaced because it may swell with age or wrong grease and cause pads to stick\wear.
@thatvegashighrisedude2757
Жыл бұрын
Do you need to do a alignment after doing this ?
@TRQ
Жыл бұрын
+ThatVegas HighriseDude No alignment is needed if you are just replacing the wheel hub assembly.
@thatvegashighrisedude2757
Жыл бұрын
@TRQ man you guys are awesome ! I bought the 2 wheel hubs from you guys , came in 1 day , and you guys reply on KZitem ! This is why I recommend you guys to everyone I know .
@Tazyz
2 жыл бұрын
wish you was my friend cause this is hell. i dont have any of these tools. can i get a list
@brandtrichardson4049
9 ай бұрын
Great vid
@unreleasedtracks3304
Жыл бұрын
can a 2007 fit a 2012 ?
@MPLVT69
4 жыл бұрын
Awesome step by step video👍👍
@marshallmcdonald7309
2 жыл бұрын
Vehicle Vehicle Vehicle Vehicle There is no "R" in Vehicle. Other than that, wonderful instruction.
@joshuarobinson2233
3 жыл бұрын
This video is great in .5 playback speed😅😅😅😅 give it a try...😭😭😭😭
Пікірлер: 26