√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Shop-TRQ-Parts √ *Do it Yourself* √ *Save Money*
@RubenMartinez-zr8rw
3 жыл бұрын
aw
@tylerrouch5763
2 жыл бұрын
You don’t need to take anything off for the driver side headlamp, just the access cover for the light. For the passenger side, you will need to move the wiper fluid reservoir which only requires a 10mm socket. After the reservoir is out of the way, it’s the same as the driver side.
@johnshields9110
4 жыл бұрын
As I am having a problem with my driver side lamp, I can only cry with anger WHO IN THE HELL DECIDED TO DESIGN A HEADLAMP THAT REQUIRES WHEEL WELL LINERS, AND THE ENTIRE FRONT BUMBER/GRILL TO BE TAKEN OFF FOR REPLACEMENT.
@TheDoowllams
2 жыл бұрын
I hope you managed to get this fixed. This video goes into amazing detail, however, it is possible to replace the headlight without taking off the bumper, there are two "hidden" screws behind the headlamp one on the left in front of the water reservoir and one just to the right of that. Then the two screws on the top as described in this video. You may then need to loosen a couple of small plastic parts on top but it's much easier than going underneath & taking off the whole bumper. I managed to do it yesterday afternoon at home, without needing to jack up the car, remove any trim or even get down under the car.
@joesmith9216
2 жыл бұрын
@@TheDoowllams many thanks for this!!!!
@sardonic_smile_8752
3 жыл бұрын
This is the most accurate video on this topic. Show us the pins on the bulbs and use accurate terminology and this video would have been better. Also an explanation of the tools used. Where do you buy replacement push fasteners?
@vipr642
Жыл бұрын
Video is useful for replacing the ballast if you have the xenon HID option just remove the head light assembly and unscrew the module from the bottom of the headlight and screw the new one in.
@jerrykampitsis3052
3 жыл бұрын
Are those xenon lights? Because mine are and there is a metal attachment (in the casing) connected to the wires. Do they need programming to work properly?
@slavyanskiyrusich3368
3 жыл бұрын
You don’t have to remove bumper to change the headlight , 2 on top , 2 on bottom between (on right ) windshield liquid reservoir and headlight (on left )between air filter and headlight , you can undo grill bolts on top for easier sliding
@TheDoowllams
2 жыл бұрын
100% wholly agree with this comment! I fully replaced the headlight at home this afternoon and I didn't need to pull off the bumper at all. You have to twist and wiggle the headlight to get it all the way out (I also loosened a couple bolts on nearby plastic parts to make it easier), but 100% easier doing it that way rather than taking off the whole bumper.
@d1ondbeat
2 жыл бұрын
how did you get to the bolts underneath the headlight assembly. I just ordered new light assemblies for my x3. would love to do this without taking off the bumper
@joesmith9216
2 жыл бұрын
@@TheDoowllams hey, please give me MORE details as to how you did it!!!
@gertryberty586
2 жыл бұрын
very good
@krookiemonster2673
3 жыл бұрын
I have an 07 x3, smashed a deer had to get a headlight off ebay and the halos don't work. The main headlight wiring clip is broken but I don't think that's the problem tho. Are the halos ran off a bulb? My old light was smashed to pieces but it looked like it was fiber optic.. any info would be greatly appreciated!
@martinvillarroel9895
2 жыл бұрын
Can i fit a 2008 x3 front and/or rear bumper in a 2006 x3?? Thanks 🙌
@montvicq
Жыл бұрын
Merci pour ce partage 👍🏻👌😉
@alanwilson1050
3 жыл бұрын
do you think its possible to remove the headlight accesing the screws through the grill cavities?
@williamsanderson9751
3 жыл бұрын
Why does it seem like there is a lock on my low beams the bulb doesn’t want to come out the plug pulls out but the bulb stays like locked in tried twisting and pulling it with a bit of force and nothing it’s hard to say what to do someone said put a little wire through the holes on the back of the bulb because there are two small holes each on one side of the bulb connectors plug?? Have you ever come across a stubborn stuck bulb ?
@Vodafone16v
9 ай бұрын
The H7 wiring harness inside my headlights is TOASTED!!! The wires are exposed and may be making contact. Anyone knows if that wiring harness is easily replaceable once I have the headlight out?
@alanwilson1050
3 жыл бұрын
models x3 2011and up are different?or do you have to remove the bumper too?
@TRQ
3 жыл бұрын
+alan wilson Thanks for checking us out! We do not have a video for this repair right now, but we'll keep this request in mind for a future video! It will be slightly different and the parts will not be interchangeable. 1aau.to/m/Shop-TRQ
@joesmith9216
2 жыл бұрын
Can you replace halogens with xenons????
@christhebeau
4 жыл бұрын
Dose it make a difference if you used the original xenon and go back with holigen lights? Can you do that ?
@joesmith9216
2 жыл бұрын
or I wanna know if you can put in xenons if you had halogens!
@tb8573
3 жыл бұрын
It´s insane that the wheels and the front must be removed to properly change bulbs!!! On my 2012 Volvo S60 each headlight assembly was removed with no tools and in 35 seconds per side.
@slavyanskiyrusich3368
3 жыл бұрын
You don’t have to remove bumper to change the headlight , 2 on top , 2 on bottom between (on right ) windshield liquid reservoir and headlight (on left )between air filter and headlight , you can undo grill bolts on top for easier sliding
@johnbudick129
3 жыл бұрын
@@slavyanskiyrusich3368 ON MY 2010 X3, IT TOOK ONY (4) FOUR STAR BOLTS, IN ORDER TO REPLACE MY DRIVERS SIDE HEADLIGHT, ALSO REMOVE AIR FILTER ASSEMBLY. THEN I WATCH THIS PERSON TAKE THE WHOLE FRONT CLIP OFF. MUST BE A FULL MOON....
@MoCityT3xAZBaby
2 жыл бұрын
Imagine having to take off the tire just to change the headlights 😒😒😒😒
Пікірлер: 30