Can the little tube that feeds the reservoir hose that comes out of the master cylinder be replaced
@arturopalomares4843
Жыл бұрын
Appreciate the video 🤙
@mambrake
3 жыл бұрын
Maybe you can explain to me how the 2017 Honda CBR1000rr keys work? Do they have chips like the Ducati’s or do you just cut them and go? My key is a sidewinder key. Let me know if you can offer some knowledge
@ExtraSync
6 ай бұрын
Where did you buy the new ignition? I bought one on Amazon and it didn’t fit the oem plug from the harness
@jasondeer9059
3 жыл бұрын
What is the ring cover called that holds the ignition in place
@MySmiley222
2 жыл бұрын
I have a 2012 R1 bought it with an aftermarket ignition switch installed. Won't run with kickstand down. Can I replace OEM switch without replacing the ECM. ? Manual says no
@cherr6red
3 жыл бұрын
Does the handle bar lock effect this process? Someone tried stealing my 08 r6 and the steering is still locked but the ignition is busted.. just ordered the parts to change it am unsure about the steering lock
@lokator1400
4 жыл бұрын
Well explained 👌
@RelaxingVibes202
4 жыл бұрын
Do u know how to make a keyless ignition?
@pefrovalenzuela9580
2 жыл бұрын
Thanks Bro 4 da info...😎
@AdvanceMotorsportsRacing
Жыл бұрын
Always welcome
@dancerrider4226
Жыл бұрын
My friend can you share the link of where I can get a new OEM ignition, I have a 2017 yamaha r1 that got stolen 3 month ago, I just recovered and now I have to replace all the keys
@kasean192
9 ай бұрын
how did you recover it?
@jazking4949
3 жыл бұрын
Did u have to program it or did the new key and ignition automatically work
@AdvanceMotorsportsRacing
3 жыл бұрын
New ignition Switch comes with key no extra programming needed.
@mrmadperfect5651
Жыл бұрын
Give the link of triple clamp that u replaced with new one. Please
@AdvanceMotorsportsRacing
Жыл бұрын
it was replaced with the original replacement unit from Yamaha
@MrVAsBoy
5 жыл бұрын
Hey bro, what are the bolts called or the part number?
@AdvanceMotorsportsRacing
5 жыл бұрын
90109-08195-00
@jasondeer9059
3 жыл бұрын
@@AdvanceMotorsportsRacing Hi do you happen to know the part number for the plastic ring cover and other bolts nuts in the video?
@hansen666
5 жыл бұрын
I'm trying to figure out how to pull them ignition bolts to pull the ignition off
@AdvanceMotorsportsRacing
5 жыл бұрын
Take the clamp off. Flip it over and grind a straight line on the ignition bolts, so you can use a flat screwdriver to loosen the bolts.
@AdvanceMotorsportsRacing
5 жыл бұрын
@@hansen666 if you want a Shop removal! You need to have a left handed drill and a Snap-on extractor kit! (For a one time removal) it's gonna be expensive on tool cost!$$
@conceptdesigns4100
5 жыл бұрын
@@hansen666 hey I heard you might need to use a torch to soften that lock tight
@hansen666
5 жыл бұрын
@@conceptdesigns4100 that's good to know thx
@conceptdesigns4100
5 жыл бұрын
@@hansen666 👍
@yucker710
2 жыл бұрын
Anybody know how to do this for an 04 r1
@carlosaviles3879
4 жыл бұрын
Where are you located
@AdvanceMotorsportsRacing
4 жыл бұрын
801 Broadway ste g Chula Vista Ca 91911
@JamieS1992
2 жыл бұрын
look at the nut after you undone it. no power tool will go near my bike
Пікірлер: 33