√ *Watch the Video* √ *Buy The Part at 1A Auto* 1aau.to/m/Visit-1AAuto √ *Do it Yourself* √ *Save Money*
@abelcp22
3 жыл бұрын
Dude this video just saved me hundreds of dollars and the little tip of letting the fluid drip saved me from having to hassle with bleeding the system.
@StacheTB
Жыл бұрын
This guy is like the Bob Ross of automotive instructional videos.
@paulsDIYsolutions
2 жыл бұрын
Watched a few of this guys videos. Great info every time!! Keep it up. Thanx
@Pattyboytheking
4 жыл бұрын
Was in a pinch today doing all of this on a 2012. Saved my ass! Cheers!
@1AAuto
4 жыл бұрын
+Patrick Rosencrants Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1AAuto.com
@geoff8253
2 жыл бұрын
Do you need to adjust the emergency break after replacing the pads and rotors? I thought I might need to do that bit it wasn't mentioned in the video.
@jimwebber7451
Ай бұрын
Great vid. I just really wish you didn’t skip over the bleeding process instead of just a quick explanation.
@1AAuto
Ай бұрын
+@jimwebber7451 Thanks for the tip! We'll pass this info along to our production team.
@RobbieBTV
Жыл бұрын
Veericle 🎉
@RobbieBTV
Жыл бұрын
Love this guy btw
@1AAuto
Жыл бұрын
+RobbieBTV Thank you! We love empowering our customers and showing how to perform DIY auto repairs with our high-quality auto parts. 1aau.to/m/Shop-1AAuto-c
@kokkolino1196
4 жыл бұрын
Hahahahahaha in the state of California it “ may cause” a Hahahahahaha good humor. Brother!!!
@te23667
2 жыл бұрын
My new caliber brackets are rubbing against my routers to the point where my tire won’t turn, what do I do
@raptorx4724
Жыл бұрын
Unfortunately the 1a auto website don't have the 2014 years for s ram
@stephenmcgraw3610
4 жыл бұрын
130 ft pound the caliper bracket
@1AAuto
4 жыл бұрын
+Stephen Mcgraw Thanks for the feedback!
@jsgadowdy
4 жыл бұрын
What can you do if you can’t get the mounting bolts to loosen?
@1AAuto
4 жыл бұрын
+MariosBiggestFan112 Playz ROBLOX 2 and Teal Thanks for checking us out! You can use some rust penetrant to try and loosen them up. If you have a breaker bar that may also help!
@ismaelgarcia4223
3 жыл бұрын
@@1AAuto I tried to get them off but half the bolt broke inside the hole how would I get it out?
@abdullahal-shimri3091
3 жыл бұрын
The dealership recommended I change my calipers at 40k miles. I live in a heavy snow and salt area
@ureasmith3049
3 жыл бұрын
That's foolishness. 40K too soon.
@stephenmcgraw3610
4 жыл бұрын
I have a 2015 dodge ram the rear calliper sliding pin i grease them up but one is still thighs to slide any idea why
@stephenmcgraw3610
4 жыл бұрын
Is the boot one piece if i wanted to get it out
@raptorx4724
Жыл бұрын
Next time go over the torque of the break line bolt , realy dude
@casperaudi7476
Жыл бұрын
IF I had a garage then I try to attempted it myself but I don’t Dodge wants$660 plus tax pep boys $494 decisions decisions.
@vekcorpestsolutions853
4 жыл бұрын
all they are doing is trying to sell you new items. the calibers can be rebuilt in 3 min. for less than $3.00 dollars each like brand new(just won't be shinny) ......oh no that wont work because it does not have a warranty better spend $150 - $250 dollars 1A auto parts......YA RIGHT
@SpaceMonkey2385
4 жыл бұрын
Yes and no. If you have a cylinder in a caliper that freezes you need a new one. As he said a bleeder that snaps off you can drill/tap but that is a lot of work that is a little sketchy and the part shown in this video is $74.95. That being said you're somewhat correct as you should change both rear or both front if you have a bad one, so that would be about $150. Also, you are correct as calipers can be cleaned and use replacement hardware to "rebuild" but that doesn't always fix the problem. Good place to start though.
@spacecoastkid5033
Жыл бұрын
Of course they're trying to sell parts. I'd rather just install a new caliper then rebuild the old one.
Пікірлер: 29