Thank you very much, this video saved the cost of a road service call and a day of waiting for service
@screamingeagle9553
Жыл бұрын
As others thank you! I thought I was going to have to install a new system and nope your video popped up and saved the day.
@truckingandfixing
Жыл бұрын
You are welcome! Glad it helps!
@truckingandfixing
4 жыл бұрын
Welcome to our channel! In today's video, Ryan will show you how to change out or replace purge value on Semi Trucks step by step. Ryan's truck is 2013 Kenworth T660. The video quality is not great, because Ryan was using just one hand to do the job while the other hand was holding the camera. Please give him some support by subscribing to our channel for more good videos. Make sure to "like" the video, so more and more people can discover our channel. Leave us a comment or question below, because we review every comment and personally reply to each one.
@Dusgf84
2 жыл бұрын
Thank you. This video helped me do it myself at home and save some money. I'd like to add, the snap ring pliers I used were 9" with a .09 size tip. The 30 dollar 12" .125 tip were too big.
@8mpgmafia109
6 ай бұрын
Dammm after 3 hours I still couldn’t get that ring off sir :/
@alfredosaldana9814
8 ай бұрын
Thanks !!! Ryan you help me to save some money 👍🏻👍🏻👍🏻
@pancholopez7457
2 жыл бұрын
Thanks to people like you is that I can work on my own truck!! 🙏 thank you!
@alek4159
2 жыл бұрын
Thanks man!!! This helped a lot. Especially when I had the same sound you have. Hopefully when I attempt this I don’t mess up. Thank you again!!
@yafeifox8865
4 жыл бұрын
wonderful video for someone who is looking to replace truck purge valves.
@PipWinsForever
23 күн бұрын
This video got me through the process. My valve did not come with install instructions. No race ring came out when I pulled the old one, so I did not use the included ring. Doesnt seem to have any problems. The biggest hurdle I had to overcome was finding the snap ring pliers. The pittsburg and quin brand from harbor freight did not work, they could not compress the ring tight enough to get it off. The $30 harbor freight Icon internal snap ring pliers worked but I had to grind down the pins with an angle grinder as they had too big of a diameter. The only other hard part was getting the old valve out. I had to put all my weight into it and twist with pliers to get it out. Thanks for the video!
@ammysanghera7474
2 жыл бұрын
Thanks ...saved me time and labour
@yusufmahdi8921
Жыл бұрын
Thank you sir this really helps
@georgiapatriot4575
3 жыл бұрын
Thanks Ryan. I just replaced the purge valve on my 2017 T680 following your instructions. Hardest part was getting the clip back in. The nylon o-ring on mine was split so I'm guessing that was causing the leak.
@truckingandfixing
3 жыл бұрын
I am glad it worked well for you! Good luck!
@johnnydubrow2279
3 жыл бұрын
Your videos are great. Thanks for sharing your knowledge. Just subscribed and I'm working my through them. Even as a company driver I enjoy learning some of the mechanics behind it all. Much appreciated
@RC-Heli835
Жыл бұрын
Those snap rings are some kind of tough!
@reitsforlife
2 жыл бұрын
Thanks for help! I replaced mine today. Had a bit of trouble getting the damn snap ring back in but other than that pretty easy.
@durmusalisaritas6343
2 жыл бұрын
Good job man thank you I will do olso I have same problem
@March808
4 жыл бұрын
Perfect video🤙🏼 can you tell me what symptoms the air dryer was giving you? Mine keeps throwing air out the purge valve, someone said it could be the whole air dryer system which I doubt. What say you?
@lyndleshelby6291
2 жыл бұрын
Hello Ryan, great video! I really enjoy your content. Couple of questions: I wonder if you would consider doing an air brake repair series of videos for every component from "nose to tail" on the truck? Would be interesting to have this content in one location with your professional explanations! Secondly, I'm looking for overhaul kit for Cummins CM570. Your recommendations? OEM? Rank order aftermarket?
@michaeldelaney995
2 жыл бұрын
Great Video, this had definitely saved me time and money!
@truckingandfixing
2 жыл бұрын
Glad to hear! 👍
@jameswalker8832
11 ай бұрын
Excellent video
@motorax11
4 жыл бұрын
Thanks Ryan. Great video. Be safe out on the road.
@truckingandfixing
4 жыл бұрын
Thank you!
@motorax11
4 жыл бұрын
If anyone else reads this. After watching this video I replaced one on my bosses 2005 Peterbilt. The main thing is having a heavy duty set of snap rings pliers to compress the ring. Perfect video for this job.Normally my boss doesn't let me fix stuff. Not because I can't. Just because he is a worrisome guy. Saved him a few days of a truck at a truck shop and a couple of hundred dollars. Enjoy.
@UpDownLeftRight55
2 ай бұрын
Hey Ryan, I’m losing air on both tanks at the same time. 2018 Kenworth t680 Paccar mx13 epa17. What were your symptoms with this issue?
@yusufmahdi8921
Жыл бұрын
Thank you sir this really helped me to change it
@georgegonzalez8818
3 жыл бұрын
Great job.
@classictruckpete7809
2 жыл бұрын
Very helpful. Thank you very much
@truckingandfixing
2 жыл бұрын
You are welcome
@cesarvelasquez9436
2 жыл бұрын
Thank you for the video, very much appreciated. Just wondering on the last part why when you go to install the new valve do you have to rush the installation? Just wondering what to look for.
@2828Meli
2 жыл бұрын
I have the same problem....air passing thru the purge valve...put a new one on and it's doing the same thing....any ideas
@slavyanskiyrusich3368
4 жыл бұрын
Clean 👍
@ryanclarke4114
Жыл бұрын
Any way I can get an opinion about an air issue? Leaking at foot valve only when hooked to a trailer.
@isaiahnelson6387
2 жыл бұрын
Good video, my 2015 t680 will take approx. 10 to 20 miles to adjust for the difference in weight concerning trailer height between drive tires and trailer,found no major leaks , leveling valve is adjusted correctly, what is with this delay in adjusting to a heavy load. verses a light load
@adamoyerbides7086
2 жыл бұрын
Thanks
@cdub5518
7 ай бұрын
I can't get the purge valve to go back in all the way and the old one won't go back in either. Any tips on what it could be?
@haiderk3246
Жыл бұрын
Thanks 🙏
@keurylara5948
9 ай бұрын
I have a truck that wont build pressure after 70 psi can it be a bad purge valve?
@ANDREASRIAL
Жыл бұрын
Exactly what's going to happen... pliers need to be able to this heavy duty snap ring.
@alexandergarneriii2656
2 жыл бұрын
How long does it take for air pressure to build back up after valve is changed
@tshaunscales8086
3 ай бұрын
How do you onow your purge valve is bad
@jjgr661
2 жыл бұрын
Hey Bud do you remember who’s the bendix part number for that purge valve replacement?
@kinggrinch5582
3 жыл бұрын
Thx for the video....my snap ring won’t snap back in though😫😫tried everything
@oralsherwood6399
4 ай бұрын
So how do you know this was a bad valve ??
@merizeru3065
4 жыл бұрын
Greatttt job
@samuelc.7153
5 ай бұрын
Make sure all the air comes out!! Drain all the tanks and keep hitting the breaks until the air gauges are at 0 and you do not hear air when pressing break.
@ricarcogarcia3983
2 жыл бұрын
awesome
@prisr31
2 жыл бұрын
I replaced mine same one and the new one. Start leaking. Some air. Su is that happen. I did the same procedure. You just did. ??? Anybody know.
@marquisharris6810
3 жыл бұрын
My issue is i have to accelerate to build up my air pressure. When im driving my tanks go way pass 120psi. When i let off the gas, eventually my low indicator warning sounds off. I have recently changed the air dryer. I can hear and feel air coming from what it seems like the same area that you replaced though. It never purges either. Any idea?
@plucky2115
3 жыл бұрын
I'd say soapy water
@4309ne20
2 жыл бұрын
Where did you get the fancy pliers
@ARNIE316
Жыл бұрын
Hey Ryan nice video! i replaced my purge value and air dryer filter on my Peterbilt 2015 today! i just needed help on snap ring coming off. I purchased a snap ring pliers at harbor tools 13 $ , they where okay ! where did you buy your pliers? you should put link for those.... Thx Arnie.
@smud4u
3 жыл бұрын
What was the original complain on these that you had ti replace the valve .??
@truckingandfixing
3 жыл бұрын
It was blowing off, and the truck would not holding any air pressure.
@samuelc.7153
5 ай бұрын
Safety eye wear!! Protect your eyes!!
@slavyanskiyrusich3368
3 жыл бұрын
If u can’t pull it out ! Mine was very old and frozen in , so I drilled a hole, put a screw in, use a hammer nail side to pull it
@truckingandfixing
3 жыл бұрын
Thanks!
@tanako98
Жыл бұрын
Looks easy. Ensure you don’t roll the seals. You willl get stuck in the middle of the road!! Do not purchase a aftermarket either.
@draconis0469
Жыл бұрын
This is truth bought one from Autozone that they no longer carry and 5 months late the upper seals have stretched and failed! Now sitting waiting to find a part!
@jerrystanton6348
4 ай бұрын
2 hour job for me. But 1 hour 58 minutes of it was just getting the old snap ring off lol.
@SophiaFox
4 жыл бұрын
support
@2828Meli
2 жыл бұрын
I had the same problem with air blowing thru and put a new one on and it's doing the same thing.......any suggestions
@warrenhardie163
2 жыл бұрын
What type of kenworth is this?
@truckingandfixing
2 жыл бұрын
2013 Kenworth T660 Cummins ISX15
@chevellebelair1402
9 ай бұрын
Mine has a bolt not a snap ring
@followeroftheway7
4 жыл бұрын
Just a little fyi I was told today they are waving the hazmat for now at landstar so I can go ahead and put my app in.
@truckingandfixing
4 жыл бұрын
Thanks for the info. Best luck on everything!
@jayfloyd3918
4 жыл бұрын
Road-Field-Home with Ryan & Sophia Hey Ryan, just came across this video while looking to see if changing the purge valve was something I could do myself. Great video and very instructional! Going to grab one while running across80/84 to Oregon and try it. Thank you for taking the time to make this video. I’ve definitely subscribed. The bonus was finding out you’re at Landstar as well!
@Huertign000
2 жыл бұрын
What's the pasrt #?
@nunyabuziness8421
Жыл бұрын
Air compressor is weak taking that long to build up pressure
@garycarroll9447
3 жыл бұрын
Y’all should use go pros to do video plus you got two hands and should be able to edit
@nunyabuziness8421
Жыл бұрын
This isn't step by step you don't show you taking the valve out
Пікірлер: 76