Outstanding job & flawless procedure. I watched your video in an attempt to diagnose a hissing sound near or around the power steering pump. I found no other possible leads on YT that pinpoint this problem. Thank you !
@s33therfan
2 жыл бұрын
Thank you for sharing and the excellent feedback.
@multinaire
2 жыл бұрын
@@s33therfanProblem found: worn power steering belt due to corrosion making contact with the pulley. Sprayed some "Awesome" on belt to verify...no more hissing. Plan: Wire brush pulleys & replace belts (easy fix). Thanks again.
@adewuyimicheal6467
9 ай бұрын
@@multinaire Wise Man I Love This Help Me
@breatheandsqueeze2191
Ай бұрын
Thank you so much for your videos. Having a college degree as a mechanic, not all the time do we always now how to fix every car. The point of view with your go-pro is absolutely perfect. Your description and explaining things is great. Not everything has to be by the book. My issues were all the grounds and where they all hooked up going back in the edge. Thank you again for taking the time and effort to help us guys/gals out.
@s33therfan
Ай бұрын
Thanks for watching and the amazing feedback.
@addjaysense
Ай бұрын
Finally found a complete and detailed video for this vehicle. Thank you for sharing
@s33therfan
Ай бұрын
Thank you for watching.
@sheliawhitson5839
3 ай бұрын
I love this video. He did a great job on removing this engine and transmission. I used this video to remove my engine and transmission from my 2011 Ford Edge limited. Thank you so much.
@s33therfan
3 ай бұрын
That is great to hear , and I appreciate the terrific feedback.
@dronepilot260rc
4 ай бұрын
You are a life saver! I’m getting ready to do this on a 2014 flex. Had a feeling the front end would have to be removed if not using a lift to drop it from the bottom
@s33therfan
4 ай бұрын
Thanks for watching.
@smittysmat7826
3 жыл бұрын
Getting ready to do the exact same job on my 07 Edge. Thanks so much for posting.
@s33therfan
3 жыл бұрын
Thanks for the great feedback , it is much appreciated.
@lonniechartrand
2 жыл бұрын
Excellent video! Though I am NOT a mechanic, this video helped me to understand what my dealership had to do when they replaced my 2017 Ford Edge's engine due to the cracked block and leaking coolant into the engine. Luckily, this was covered under warranty! You did a fantastic job explaining in DETAIL all of the steps necessary to complete this job. And I was very impressed that this was done in your driveway and not some expensive garage shop!!! Thank you for taking the time to explain this step by step as I am sure it added greatly to the time it took for you to remove this engine.
@s33therfan
2 жыл бұрын
Truly appreciate the great feedback , thank you.
@FreedomRock44
Жыл бұрын
Was your mileage low before the engine went???
@davidristow6939
Жыл бұрын
Excellent work and teaching I have 2011 Edge with 339628 miles on it and still in great running condition and solid body I will definitely use your work procedure in replacement of my engine Thsnk You
@s33therfan
Жыл бұрын
Thank you very much for the feedback , these Edge seem to last a long time . Thanks for watching.
@johnzimmer4857
2 жыл бұрын
My water pump died and made an oil milkshake. Ordered a used engine with 60k on it, going to start ripping the old one and this video is a great walk through. Thanks for taking the time to make it
@s33therfan
2 жыл бұрын
Thank you for the feedback and best of luck on your install , hope all goes smoothly.
@johnzimmer4857
2 жыл бұрын
@@s33therfan I just finished it up and drove it today. Took me about 5 days to get it all done. Only had a few speed bumps during the process but nothing crazy. Can’t thank you enough for this video, it was very straight forward with great details. This engine has 63k and I have a jasper transmission with 80k on it so hopefully I can get another 100 out of it.
@saltycreole2673
Жыл бұрын
I live in NM. I have a 2010 Ford Edge SEL 148K miles. Blown heads. Either shops here want $200 an hour labor or the young mobile mechs don't want or need the money. (I live very rural) So I'm doing it myself. This video is right on time. Thanks.
@s33therfan
Жыл бұрын
I appreciate you sharing this information , it helps show others the hurdles when an issue like this arises. Great job on tackling this , and saving a lot. I hope all goes smoothly. Thank you for the feedback.
@saltycreole2673
Жыл бұрын
@@s33therfanFound a used motor $1,095, 55K miles on it. I wonder what it came out of. You mentioned the oil filter was different. We'll see. $4,300 for a new engine is just too much. Blessings.
@ryanmacewen511
2 жыл бұрын
Man, this was the coolest video. Takes me back when I was younger and did crazy stuff like that.. all hand tools. I've definitely gotten soft. Aches and pains of aging. But where there's a will, a way will present itself. Thanks for sharing!
@s33therfan
2 жыл бұрын
Thank you for the great feedback and thanks for watching.
@contrastbeats6443
8 ай бұрын
Super helpful video. Going to do my first transmission swap and I loved how you showed both taking apart and putting back together 🙏🏾
@s33therfan
8 ай бұрын
Thank you very much for the great feedback.
@larryrussell1900
11 ай бұрын
Yes thank you for this video, it is giving me the confidence that I need to do my own motor change.. your always reminding to label things, so you know how to put it back together,, thank you for this video
@s33therfan
11 ай бұрын
Thank you very much , love this comment.
@markmott5862
Жыл бұрын
I am in the beginning stages of "swapping a motor from one ford edge to another," and have to admit... once you got to the last quarter of the reinstall i got anxious.. lol... been here a few times and done that. but couldn't help but to get excited for a test start! good job on this video... other than a few "small" "semantic issues" of like routing of hoses and e.t.c I have to admit, this was an excellent Video! Great job!
@s33therfan
Жыл бұрын
Thank you for sharing and thank you for the great feedback.
@genehunsinger3981
5 ай бұрын
1:15:54---lefty loosie,,,righty tighty,,,LOL.Good clear instructions on this job.
@mannyvasquez39
3 жыл бұрын
Thank you so much for this video whenever the day comes for my 2010 ford edge I will definitely use this video
@s33therfan
3 жыл бұрын
Thank you very much for the kind words , I appreciate it.
@abrahamo8934
4 жыл бұрын
Man I wish this video was here so long ago 🤣 great video!
@s33therfan
4 жыл бұрын
Thank you for the feedback I appreciate it , and thanks for watching.
@ryan7625
2 жыл бұрын
One of the best videos I've seen on KZitem for any motor job I've done great video !
@s33therfan
2 жыл бұрын
Thank you for the kind words , much appreciated.
@khalidrudwan2057
3 жыл бұрын
Great job, you let me know a lot of my Ford Edge
@s33therfan
3 жыл бұрын
thank you for the great feedback, it is much appreciated
@rdillard67
2 жыл бұрын
Great video!!! Lots of details & information; long & tedious but it needs to be. Will be pulling engine in my 2008 Edge with 160kMiles, to replace InternalChainDriven WaterPump, a NotoriousFailureItem on these 3.5L engines. Will also renew the TimingChain assembly, upgrade to a HighVolume Melling OilPump, & renew the AllWheelDrive PTU\GearBox + CVAxles + Shocks + Brakes. Again very good video, thanks for taking the time+trouble of making it.
@s33therfan
2 жыл бұрын
Thank you very much for the great feedback , best of luck on this project and thanks for watching.
@angellaos7826
Жыл бұрын
Very good explanation. Thank you for this video.
@s33therfan
Жыл бұрын
Thank you for the kind words.
@kawika83gois23
8 ай бұрын
veery efficient , job well done, poste more videos, very very very helpful. thank you.
@s33therfan
8 ай бұрын
Thank you very much for the kind words , and thanks for watching.
@jamescollins5073
2 жыл бұрын
Just found your tutorial lol, which really gave me an idea on what i need to do with dealing with a 2007 Lincoln mkx that has a transmission shudder. The transmission fluid was dark in it as well, replace what i could with fresh fluid along with some shudder fix. If the shudder doesnt go away, ill have to pull it.
@s33therfan
2 жыл бұрын
Thank you for sharing and the great feedback.
@joeymessantonio4356
2 жыл бұрын
about to do a swap with no lift and needed to see how to remove the front end to get it out with the cherry picker. Appreciate it.
@s33therfan
2 жыл бұрын
Thank you very much for the great feedback , hope all goes smoothly on your project.
@dayslife
3 жыл бұрын
great run through the process and details. enjoy!
@s33therfan
3 жыл бұрын
Thank you very much for the kind words and thanks for watching.
@jameswiggins7437
3 жыл бұрын
great video i am fixing to use it to replace motor in my 2010 edge
@s33therfan
3 жыл бұрын
Thank you very much for the great feedback and thanks for watching.
@Neon_Deion
2 жыл бұрын
Thanks for this video man, helped me make some extra $$$$ with ease! 👍🏼
@s33therfan
2 жыл бұрын
Thank you for watching and the great feedback.
@jon2787
10 ай бұрын
I didn't know junior from Reno 911 did mechanic videos.
@berad187
2 ай бұрын
For a guy thinking to remove this engine without the transmission it would not be possible because of how much of tight space it's sitting in because I once thought it was be possible but I was wrong on that Idea
@s33therfan
2 ай бұрын
Exactly right , thank you for this comment.
@ericbrown6449
2 жыл бұрын
Did you put a new water pump in? Super job on the video with great detail!!
@christiankoehn7331
2 жыл бұрын
Good job my friend
@s33therfan
2 жыл бұрын
Thanks for watching.
@cookierepairprojects4544
8 ай бұрын
looks like when they updated the engine at around 2011-13 it no longer has the second engine hook, ford makes you buy that extra at $150 part number is 303-1245
@s33therfan
8 ай бұрын
Thanks for the information , and thank you for watching.
@jkjwf
2 жыл бұрын
This is an awesome video I’ve been working on my 2010 Mazda CX-9 and they are very similar engine designs, both Ford. I removed my radiator, valve covers and now I’m about to work on the rear exhaust manifold. Would you know if the rear exhaust manifold gasket is the same as the front exhaust manifold gasket and how it sits on it? Once again thank you for this video.
@TheMoore16
3 ай бұрын
Hi Thanks for the video it's 👍. Is this the same setup as a 2013 3.5 does anyone know of any difference
@oc9215
2 жыл бұрын
I’m planning on swapping my engine too, but I think it’s too much of a work for me and it’ll take too much time and end up not finishing it. Good explanation tho
@s33therfan
2 жыл бұрын
Thank you very much for watching.
@michaeleagan7821
4 ай бұрын
Is this the same as a 2008 lincoln mkx? I think my mkx has something internally broken... it wont turn over. Am i going to have difficulty taking those bolts out from the (was it the flywheel or the transmission? You took the plastic shield off and had 3 bolts that you had to take out... had to turn it over tonget to them... 1:11 on your video.
@s33therfan
4 ай бұрын
They are basically the same. You will have to pull the torque convert out of the transmission if the engine is locked. You will want to replace the torque converter seal as well. Having said that a lot of times the bolts or nuts are so tight they may not be removeable even at this point. In these case I disassemble the engine. Just had this exact issue on a recent project. Thanks for the feedback.
@ryanbeshears931
2 жыл бұрын
On that tranny line. Blast some air in there first to get lose dirt. Then blast it with a decent amount of brake clean and then an air hose agin then some wd40. Works well for me
@s33therfan
2 жыл бұрын
Some great information. Thank you for sharing and thanks for watching.
@bradholmes1919
2 жыл бұрын
I would love to say amazing video I bought a 2008 ford edge with a blown head gasket and your video made it some easy. I took it out and replaced it thanks to your video. I put it all back together and starts up great but when I put it in drive it just revs up I changed the transmission fluid torque convertor and checked the shifter links. Any ideas of what it might be?
@s33therfan
2 жыл бұрын
Great job tackling this project , and thank you for the terrific feedback.
@Texaca
2 жыл бұрын
... do you have Codes on it? If you haven't checked them, you should, most Auto parts stores have an OBD scanner, that they can lend you to read the codes.
@elroyjetson1285
3 жыл бұрын
When can you do mine?🤔😅
@exoticr6andbmx99
4 ай бұрын
with the AC lines, should i drain the freon before disconnecting the lines?
@s33therfan
4 ай бұрын
If this sytem has freon you will want to have it vacuumed out by a shop. The other method I use a lot of times is simply moving the condenser and compressor out of the way and removing the engine. Having said that you will most likely need to remove everything from the front. I have a lot of engine removal videos for reference if you want to check those out. Thanks for the feedback.
@jeffenright5146
3 жыл бұрын
Thanks for a great "courage building" video. i picked up my replacement engine today. I am going to try to use your topside approach BUT only pull the engine and not the transmission. I am hoping to save disconnecting all the brake parts and axles.... If you have any tips on this I would love to hear them. I am concerned there may not be enough clearance to clear the flex plate. Any thoughts are greatly welcomed. Thank you very much. Jeff
@s33therfan
3 жыл бұрын
I think you could pull it out , you may end up having to remove more from the engine front to allow slack to slip it out of the transmission but it should be doable. I do not usually do it this way but I have removed van engines this way so I don't see any reason an edge wouldn't work. The advice I always say is to label everything(or a lot of pictures), and try to put bolts and nuts where they came from when possible while removing. Best of luck on your project and keep me updated on how it turns out. Thank you very much for watching.
@jeffenright5146
3 жыл бұрын
@@s33therfan Success !! I was able to pull the engine ONLY without the transaxle. My car is AWD so I did have to disconnect the Passenger side Axle to gain access to the PTU (transfer case) mounting bracket. Also, there is one enginre to transaxle bolt which is "blind" and nearly impossible to remove this way, but with patience and mirrrors it can be done from the top. Thanks for your excellent video which truly inspired me to try this. New junkyard engine rus great with no leaks and no check engine codes at all. Thsnks again , Jeff
@jameswiggins7437
3 жыл бұрын
i started my engine replace today.
@s33therfan
3 жыл бұрын
Best of luck on yours. I hope all goes smoothly. Thank you for watching.
@omarvargas4320
2 жыл бұрын
Can you swap a ford edge 2011 3.5 v6 duratec engine with a ford explorer 2013 3.5 v6 duratec? I have a ford edge 2011 with a blown engine and found a cheap 2013 ford explorer engine. Seem to be the exact same engine
@s33therfan
2 жыл бұрын
Yes , you can even verify it with the casting numbers on the block. Thanks for the feedback.
@joshual5866
3 жыл бұрын
Thanks for posting this video. Just curious, did you have to let the freon out of the ac during this process? I am getting ready to do this on my 07 and wanted to know what to expect
@s33therfan
3 жыл бұрын
I never do unless removing the engine does not allow for it . In this case I did not , most of the time I remove the compressor and use a strap to hold it aside. Sometimes I can do the same thing with the power steering pump just to avoid draining the fluid. But I will just tell you that this engine besides the explorers are one of the easier engines to swap. Best of luck on yours and thank you for watching.
@joshual5866
3 жыл бұрын
@@s33therfan I am unfamilar with ACs but i thought you disconnected the high pressure lines using those scissors? DOnt those lines have the freon in them?
@s33therfan
3 жыл бұрын
You are correct , I get these cars mixed up once in a while. In this case there was no freon in the system so I was able to disconnect without taking it to a shop to be evacuated. If I had wanted to avoid this I would have had to drop it out of the bottom. It would have made things more difficult to say the least. So yes I would have the freon recovered. Thanks again for watching.
@joshual5866
3 жыл бұрын
@@s33therfan Awesome. Thanks for the response. I will pump out the freon before i touch the high pressure lines.
@jennypadilla5632
2 жыл бұрын
I just had mine replaced due to severe oil leak. With that being relaced, did the coolant and freon need to be drained? Or does it depend on the mechanic?
@fmorrison81
Жыл бұрын
I have 2010 edge. I fixed obd code p0345. Changed spark plugs, sensor, coil, and did a tune up. Mechanic says my has no compression. What should I do?
@s33therfan
Жыл бұрын
You could get a second diagnosis by another shop , but it sounds like the engine may be bad . Best of luck on whatever you decide. Thanks for the feedback.
@harrybalsonya5619
Жыл бұрын
A P0345 is a cam position circuit fault. Does it even run or does it have a misfire?
@shanegrahamsr.2933
2 жыл бұрын
how's the transmission holding up? thinking of doing the same with 260k
@s33therfan
2 жыл бұрын
Transmission seems perfect. Surprisingly from my experience they all seem pretty tough. Thanks for watching.
@jameswiggins7437
3 жыл бұрын
what year ford edge motors are compatible with the 2010 edge sel
@s33therfan
3 жыл бұрын
As far as the edge go anything from 2007-2010 should work. Thanks for watching.
@anthonytabs1901
3 жыл бұрын
What would say labor hours would be on this replacement.
@s33therfan
3 жыл бұрын
I would say a minimum of 3 days to complete everything. Thanks for watching.
@Texaca
2 жыл бұрын
... the Labor cost is more than the Value of the vehicle... 😅 Great video thou, and good use of your camera.
@mickeywinebrenner6455
4 жыл бұрын
The engineer that designed those transmission line connectors is a horrible godless individual that obviously hates mechanics and enjoys making people suffer.........they probably put the ice trays back in the freezer empty as well.
@s33therfan
4 жыл бұрын
Best comment ever. I have always despised these connectors and thought how a simple clamp is so much easier. Thank you for the feedback and thanks for watching.
@dhigareda83
3 жыл бұрын
similar procedure to remove the engine on a 2010 flex?
@s33therfan
3 жыл бұрын
Check ou this video , it is going to be more similiar . Thank you for watching. kzitem.info/news/bejne/06OOy4Snkod3oKQ
@harrybalsonya5619
Жыл бұрын
No, you don’t have to remove the cooling systems and core support. The Flex engine will easily come out from the top.
@sireposey8556
2 жыл бұрын
I put my wife's in the shop,they replaced the water pump which is internal,got it outta the shop,she drove it twice,now it won't start and has low engine light on,im hoping just a Oil pressure sensor,🙏
@s33therfan
2 жыл бұрын
If there was not coolant in the oil , it may be okay. Hope everything goes smoothly. Thanks for watching.
@sireposey8556
2 жыл бұрын
@@s33therfan there was coolant in the oil and they changed the oil and filter 3 or 4 times and replaced several parts,it went back to the shop yesterday, so hopefully they can get it figured out
@johnzimmer4857
2 жыл бұрын
What was the outcome?
@larsbambi1575
2 жыл бұрын
3.5 integrated water pump failure...fills the crankcase with coolant. Catastrophic damage 😪
@s33therfan
2 жыл бұрын
Yes , I did a video on a Mks 3.7l ( pretty much the same) luckily it only leaked out the weep hole and no coolant in the oil. Not an enjoyable project thiugh. Thank you for the feedback.
@stolenrider07
3 жыл бұрын
Do you have to pull it with the trans?
@s33therfan
3 жыл бұрын
It is possible to do it without the tran but questionable if it would be any easier. Great question and thanks for watching.
@jameswiggins7437
3 жыл бұрын
when they talk about oil cooler is that the transmission oil; cooler
@s33therfan
3 жыл бұрын
Could be either the the transmission or the actual engine oil cooler . Some vehicles with 3.5l ( edge included) have this oil cooler. I really do not know why unless it is a towing feature or performance etc. Maybe someone else can chime in on this. Great question and thank you for watching.
@jameswiggins7437
3 жыл бұрын
@@s33therfan so the fact that my new engine's coming without one will I need to get one. My truck does not have a towing package on it
@krisehlen7602
2 жыл бұрын
Was this an AWD?
@s33therfan
2 жыл бұрын
This one was just a front wheel drive . Thanks for watching
@jquintanilla9354
2 жыл бұрын
Looking for a transmission for the same car! Anyone can help me with that!
@s33therfan
2 жыл бұрын
Try ebay , they have numerous transmissions for these , as low as 400 to 500 delivered. Thanks for watching.
Пікірлер: 128