I've never heard the bread in pipe trick. That's awesome
@MazdaMitch
Жыл бұрын
Learn something new every day.
@kevlarorc
Жыл бұрын
The timing of this video is insane. I'm doing this job on my b2600i this week. Thanks for the upload!
@martinpena9791
10 ай бұрын
Is it the same for the b2600? I need to change the clutch and flywheel. Also the main seal removal was extra right or that need to be be done also?
@kevlarorc
10 ай бұрын
@@martinpena9791 Yep, process is the same for b2600i. Some minor differences like number of bolts in the flywheel. If you're already that far in you should do the rear main seal. That part is easy. Wrestling with the transmission under the truck when trying to mate it back up was the hardest part.
@martinpena9791
10 ай бұрын
Cool thanks!! My clutch went out and I was quoted 1000! Gonna ho ahead and do it myself after watching this vid haha
@shon9893
Жыл бұрын
You’re my motivation on making truck, my next project car
@MazdaMitch
Жыл бұрын
That's awesome
@jtoo6060
Жыл бұрын
Another excellent how to video. When you removed the short console I noticed that there’s two brackets that hold it down to the floor. When I see these short consoles for sale on eBay they almost never have the brackets.
@dakotamedlin48
10 ай бұрын
Just subscribed trying to replace a few things on my truck still learning
@thecuss6817
Жыл бұрын
Really good video. Good about the shift bushing and rubber boots. You guys need eye protection when under a vehicle !!! Don't most clutch kits come with a new pilot bearing? In instances of clutch slippage, I always do a new pressure plate and disc, and get the flywheel done professionally or replace. I've run a Luk clutch kit for at least 15 years in mine.
@MazdaMitch
Жыл бұрын
None of the stuff we used was from a kit. It was from an engine that we pulled which had a fairly new clutch and pressure plate and flywheel on it. That's why we had to go in and get the pilot bearing. No stores around us had one but these both were fairly new.
@MazdaMitch
Жыл бұрын
Yes we forgot to wear our protection and we had it right there on the table.
@senditreloadit
Жыл бұрын
I’m on here watching like I got a Mazda.
@rottsrule2505
Жыл бұрын
I love your hands 😂😂😂
@angelrios6694
Жыл бұрын
🤣
@kz6fittycent
Жыл бұрын
I want one and I want to gut it, replace the 4-cyl with a 13BT (rotary), well built transmission, suspension, and go win some races in style.
@pauloisidoro2
Жыл бұрын
Thanks for uploading ,really good info 👍
@BeaterCollector
Жыл бұрын
Good job guy's, Thank you for your advice big time.
@MazdaMitch
Жыл бұрын
Thanks for watching
@thc61976
7 ай бұрын
Thank you so much !
@zero-point797
7 ай бұрын
Thank you...
@MazdaMitch
7 ай бұрын
You're welcome!
@jtoo6060
Жыл бұрын
That black rubber boot that was under the console is still available as Mazda part number : UB39-64-491. Mine was missing on my 1991 B2200 and I bought one on Amazon. They are also on eBay
@MazdaMitch
Жыл бұрын
Thanks! Yes I have parts listed on the parts page at my website. www.mazdaminitruckin.com/info/parts
@manuelcordova5539
Жыл бұрын
En mi caso tuve muchos problemas con el buje piloto, ya que estaba desgranado y tenia nomas el puro aro de acero, fue un dolor de cabeza sacar ese maldito aro 😅, saludos 👍
@jtoo6060
Жыл бұрын
Would you happen to have a Amazon link for the small plastic cup that you mentioned should be at the bottom of the shifter handle and when it’s missing it causes the shifter handle to be sloppy. Thanks
@MazdaMitch
Жыл бұрын
amzn.to/3hZdoGn
@CHVLKiD
Жыл бұрын
Great video and much appreciated, we’re struggling to get our new clutch system bled out and working properly…can you suggest anything?🙏🏻? We’ve tried bleeding the slave cylinder, the master cylinder, pumping, not pumping etc. You’re the Man, any suggestions would be greatly appreciated Master Mazda Mitch🙏🏻🙏🏻
@MazdaMitch
Жыл бұрын
Be sure to use a copper crush washer where the rubber line goes into the slave. New lines and new slaves do not always come with them and if you don't use one you'll get air in and never get it bled out. I usually gravity bleed everything since I'm by myself.
@CHVLKiD
Жыл бұрын
@@MazdaMitch Thank you for getting back to us so quickly. I believe we do have the copper washer there but we’ll definitely double check. Can you please share details of what your gravity bleeding process is? Again, we appreciate your knowledge and advice 🙏🏻
@MazdaMitch
Жыл бұрын
@@CHVLKiD search for gravity bleed on KZitem and you'll be on your way.
@CHVLKiD
Жыл бұрын
@@MazdaMitch Will do and thanks again for your help sir🙏🏻
@GurwinderSingh-xk5fb
2 ай бұрын
Hsllo mate, thanks for tge video. Do we have to take out the gearbox to replace oil pan gasket? I cant see the very rear 2 bolts for the pan
@MazdaMitch
2 ай бұрын
These trucks do not have an oil pan gasket it's just a machined surface and all you do is use gray RTV. Your leak could be coming from further above. Can the pan come off without removing transmission yes. There are two brackets that help stabilize the transmission that you may have to remove
@GurwinderSingh-xk5fb
2 ай бұрын
@@MazdaMitch thanks for replying mate.
@chadjohnson6782
2 ай бұрын
Hey guys, if a flexplate bolt is missing completely, will the B2200 have a severe oil leak?
@MazdaMitch
2 ай бұрын
Yes each if the six bolts holding the flywheel on, go directly into the crank and through the crank. They normally come with sealant on them. You can use a bit of high torque grey RTV on the bolts
@klearman9612
Жыл бұрын
Bro how on earth did you get those 4 bolts out on top of the starter there’s no room to crack them any help?
@MazdaMitch
Жыл бұрын
I'm not sure of the ones you were talking about. My advice is to just get some extensions some wrenches and get after it just like we did.
@803Drake
Жыл бұрын
So I replaced my clutch and I have no reverse anymore. I had reverse before I put the drive shaft back on. Now I do not. What do I do?
@MazdaMitch
Жыл бұрын
I think you need to be more specific like do you mean it will not go into reverse without it grinding or something? Because reverse gear and 5th gear are on the same gear in the transmission it's really unrelated to swapping the clutch out.
@adampayan1953
Жыл бұрын
Hey Mitch so when installing the pilot bearing will I have to knock it in until it stops? Or is there a specific depth it’s suppose to go in at?
@MazdaMitch
Жыл бұрын
Till it stops and you'll hear the pitch sound change. You will be able to tell it's bottomed out
@adampayan1953
Жыл бұрын
@@MazdaMitch awesome thanks for the help!
@803Drake
Жыл бұрын
Looking for a rear main seal link if you have one. Thanks.
Пікірлер: 49