BUY THE AUTO PARTS you need for the operation : 👉 bit.ly/cheapAutoparts 👈 📱 DOWNLOAD THE APP : 🍎 bit.ly/MCD12AppStore, 🤖 : bit.ly/MCD12PlayStore 📱 ⬇︎⬇︎ 🔥 🔧🔧🔧 🔥⬇︎⬇︎
@5uperhands
3 ай бұрын
Just about to have this done to my car... watched it so I could sympathise knowingly with the poor schmuck who I am getting to do it! Wish I had the skills to do it myself. Great video, thanks!
@Psychgiest
16 күн бұрын
Was thinking about doing it myself, but I’d much rather pay some one now 😂 the tools I’d have to buy would probably cost half the labour!
@slengoslengaw8510
5 ай бұрын
Removing and the installing the plastic cam cover is a probably the hardest thing in this job. Thanks VAG for the great design
@johnblanning2500
4 ай бұрын
iss there a knack to it?
@slengoslengaw8510
4 ай бұрын
@@johnblanning2500 patience.. nothing other than trying to wiggle it out without breaking the plastic cover. Follow the steps about the heat shield.
@chrispinsoza8530
4 ай бұрын
Especially removing injectors
@gabrielcraciun5315
5 ай бұрын
Very professional detailed presentation! Great job! Felicitation 😊
@itsjustchris3306
Жыл бұрын
Im going to do my timing belt next week, so this video helped me a lot
@UseTool_EN
Жыл бұрын
Good luck! This is a tricky one!
@kizzamate
10 ай бұрын
For people doing this on the diesels, not required on petrol models you probably want to open the thermostat and you won’t be able to do that without ODIS, if you don’t you have a good chance to cook the head. You don’t have to but you might want to check the coolant fill quality by pressuring the reservoir to 1.5bar after filling it abit above the plastic line (30mm up) mark the spot, if it drops below 30mm you may have a problem.
@peterszaraz2642
Ай бұрын
I was about to try this on my Octavia, this is perfect DIY guide together with service manual, but no way I'm going to do this :D (i do lots of basic maintenance on my car including diagnostics) which makes me really mad. I do not trust any shop, including Skoda's, but most probably i will end there watching through their fingers :) otherwise i can see f.e. how the little shield won't be added back etc.
@tommykemp4966
9 ай бұрын
Can someone tell me why does he slacking off the cam and fuel pump pulley
@Egoreni
3 ай бұрын
The bottom plastic sequence was showed after the damper pulley was installed :D
@torevenheim9607
3 ай бұрын
On Skoda Fabia 1.6hdi 2012 i service book say intervall 198 000 km and no time limit, very strange
@mejdibelja6455
6 ай бұрын
After your replace when you need to replace again 60.000 km 80 or 120 or 150.000km i have a GATES - Ref: KP15678XS-1 set
@MenTz_Evil
11 ай бұрын
A question. The water pump for Vw golf 1.6 17 plate is it switchable or non-switchable
@mejdibelja6455
6 ай бұрын
The waterpump 10 minuut or 10 times in collant?
@UseTool_EN
6 ай бұрын
10 times will be enough. 😄
@milhousevanhouten3048
9 ай бұрын
There is no link to "How to bleed the coolant Golf mk7 1.6 or 2.0 TDI" video in the description. Was this deleted for some reason?
@arkadius87radom
7 ай бұрын
Did you found it m8?
@tomspeed2000
4 ай бұрын
Is anyone knows when or after how many km the distributieriem should be replacing? The total km is 130,000
@UseTool_EN
3 ай бұрын
Hi @thebronzedadonis ! This is why we make these videos! 🔥
@kristianmurrizaj4602
3 ай бұрын
How many km must change on a golf 7 ? 1.6 tdi 2014
@guitarFAIL
2 ай бұрын
either 10 years or 210.000km. if you haven't changed you should do it ASAP! cheers
@TomoReso
3 ай бұрын
Thanks!
@UseTool_EN
3 ай бұрын
Hi @TomoReso ! We're glad we could help you out. Hope the operation went well 👌
@TomoReso
3 ай бұрын
@@UseTool_EN It did, there is a small mistake in the video tho, when putting all back together, first we put this lower timing cover plastic along with engine carrier, then the crankshaft accessory pulley, not the other way around. Costed me 5 minutes, but no biggie! Video is great otherwise, very well covered. Thank you again!
@abubakarimahyoro
Жыл бұрын
Without a dealer doing this work, it's a nightmare as a DIY for a common person
@Amigow0w
Жыл бұрын
This is something that you shouldn't do if you are not 100% sure that you can do it ! And even if you know what you doing, you need to make sure you've got the right tools 👌😎
Пікірлер: 34