Mate top video. I am doing the water pump and radiator hoses on my Mazda tribute it has exact same engine and almost exact same setup. I am a little concerned now as I didnt buy the whole pump assembly just the pump so fingers crossed my plastic hasnt failed. I havent had any major issues its just preventative maintenance. Two excelllent tips I got from you were the non tensioner belt issue and the flexible hose clamp. Saved me some frustration there. Anyways thanks for the video, good work.
@briansmobile1
11 жыл бұрын
You're welcome- always great to hear from you. Happy New Year!
@briansmobile1
11 жыл бұрын
My dad was a mechanic and spent a lot of time on me when I was growing up. I've been doing it my whole life. I've been doing it unsupervised/independently for 27 years.
@markn8376
2 жыл бұрын
I think I would have been reluctant to do this job myself without this video tutorial. It was a huge help. Thank you for posting! Wish I could find a video on how to do a coolant flush and fill. I'm unclear on how to burp the system. And apparently there's a valve for the rear heat, too.
@AkLrBeIwON
7 жыл бұрын
you can remove the belt by rolling a flat head screw driver between the top pully and the belt. you have to crank the motor so pull the fuel pump relay in the engine bay fuse box. start the car while clear of engine to make sure it uses all the fuel left in the lines. Once it dies crank it again just to double check that it won't start up when you're removing the belt. then have a buddy crank it a little at a time while you put the screw driver between the belt and pully, kinda lift on the screw driver as it rotates and it will slip on or off easier. Replace fuel pump relay. or just cut the belt to begin with and buy a new one to only have to worry about putting on a belt and to have a new belt on there is smart.
@StilSlepn
11 жыл бұрын
I'm stuck at work but at least I have something high quality to watch...thanks Brian & Spanky, Happy New Year!
@briansmobile1
11 жыл бұрын
My brother is in Texas finishing up medical school. He was here for Christmas.
@tiffanyyuan4480
5 жыл бұрын
Nice to watch the video showing how to changing water pump, because it is Feilong Jiangli's perfeesional area. Feilong Jiangli professional supply water pumps, oil dipsticks, rubber parts.
@D6Spanky
11 жыл бұрын
The brand we happen to have in the shop is Western Safety. Brian's been using the blue Heavy Duty gloves and I have been using the black Extreme Heavy Duty. I think it's a Harbor Freight brand.... yeah... I think so. :)
@briansmobile1
11 жыл бұрын
GM Dex-cool is supposed to be a long term coolant that preserves the lining/coating in GM water jackets. Never mind the fact it eats ABS plastic parts. When you use Ethylene Glycol (Green antifreeze) in with it, it just strips that anti-corosive ABS protecting coating. (the crud in your tank.)
@48wilber
7 жыл бұрын
4:45 Pry Bar?? "NOOOooo don't do it!!!" laughed a little! (only a little,,, because I did break some plastic on my first one! DEFINITELY wait until the belt is of and pump is loose before trying that one! Thanks somuch for the excellent videos Brian!!!!!
@48wilber
7 жыл бұрын
PS,,, what if i don't have a "Spanky" to pull on the rope???
@walterbrunswick
11 жыл бұрын
So, Mazda uses a lot of Acrylonitrile Butadiene Styrene and anti-freeze (from the factory) that dissolves ABS... great engineering Mazda... bravo.
@briansmobile1
11 жыл бұрын
I see that all the time. Dexcool definately eats the ABS plastic components. It makes them extremely brittle. The intake manifold gaskets are based out of ABS.
@020119571
11 жыл бұрын
great video brian.never have done a new mpv before.after getting hose clamps off I like too use a cotter key tool too loosen the hoses.its a bit pointed but not too sharp.run it between the end of the hose and the fitting....max
@briansmobile1
11 жыл бұрын
Factory manuals. I used to work for a software development company doing labeling, QA, and stuff. I have most of them.
@shepd3
11 жыл бұрын
Hey, look, since the auto manufacturers have to actually provide some rust resistance in the body work nowadays, they gotta find SOMETHING to corrode and fall apart so you have to buy a new vehicle. I'm just amazed they said "Screw it" to metal parts and instead figured out a way to make plastic "rust". :D
@sailorbob74133
Жыл бұрын
The reason for all that check ABS plastic is emissions regulations - plastic is way lighter than metal so it increases fuel efficiency by a fraction of a percent to meet government regulations.
@zoefaith120
4 жыл бұрын
Hey, Brian I am Brian too. I just got a 2004 mpv v6 and if this needs with these. At least I know , what the neck is going on. Knowing is half the battle with touchy tight places.
@hp11208
11 жыл бұрын
I have a 2000 mpv,happy new year Brian.
@walterbrunswick
11 жыл бұрын
"won't come, won't come, and then all of a sudden UGHH, it's freakin' everywhere!" THAT'S WHAT SHE SAID! lol couldn't help but say it...
@briansmobile1
11 жыл бұрын
Thanks Walter! That's a mouthful isn't it?
@santi9532
Жыл бұрын
You didnt have to remove the pulley for this job? Been having issuea trying to do it with the pulley in the way. Might have to use a puller
@zoefaith120
2 ай бұрын
What green coolant would you prefer to use on these engines ? I read they are two for mazda these years...
@briansmobile1
11 жыл бұрын
Brilliant.
@josebutmkveuos2602
9 жыл бұрын
What happens if the pulley is in the way of the last screw holding it in place?
@Ghandisgarage
11 жыл бұрын
Great video!, i like the older MPV's used to have one with a 5speed and diff lock, did pretty well for a minivan. (the title says mvp.)
@spelunkerd
11 жыл бұрын
That's a great idea to check for leaks before replacing coolant. By the way, is he your brother?
@anyheck
11 жыл бұрын
Howdy Brian and Spanky, Happy New Year to you! You said that the coolant in there eats up the ABS parts, I'm guessing the green cool-aid you're using is 'conventional' silicate based inorganic buffered antifreeze, but have you found that OAT or HOAT based to be better or worse with respect to that? I switched out from a silicate to an OAT (used car) for the supposed extended life, and that it's the factory coolant (Toyota). BTW have you resolved your camera situation? Thank you!
@impalaz4ever
7 жыл бұрын
Trying to do a pressure test on a mazda mpv, where can i get the adapter that you have in the video for my pressure tester. I've looked around but no one seems to have it. Thanks.
@ihungryyygaming3805
5 жыл бұрын
i ended up removing the pulley and bending it really bad. How do you recommend installing the new pulley? I ordered it new and dont want to ruin it.
@walterbrunswick
11 жыл бұрын
man, at 4:13 I got the sudden thought that automotive mechanics is like heart surgery... the spaces are so tight and the tools required are so specialized and you have to follow a certain procedure or else...
@dennisjohnson7141
6 ай бұрын
Is the abscess kind of like the same thing I have growing on my lip ??
@Pengy39
11 жыл бұрын
Happy new year Brian!
@D6Spanky
11 жыл бұрын
Welcome!!! happy new year to you, too!
@briansmobile1
11 жыл бұрын
Ha ha! They don't hate us, they just don't think about us much at all. They have space, performance, time, and cost constraints to worry about and they forget about us.
@fordwindsor351
11 жыл бұрын
Brian or anyone else, is there a safer antifreeze by means of your comment on the plastics not holding up long term due to the factory antifreeze. I currently own a 2007 Chrysler Town and Country and the antifreeze is red in color, dont know much of this either.
@mythicalmining7999
7 жыл бұрын
Great video, my water pump is stuck on and I can't pry it off, any suggestions?
@Junk65
Жыл бұрын
Excellent. Thanks
@ncrdisabled
11 жыл бұрын
My son had a 2004 jeep liberty and it has a bad light socket for the front turn signal. I went to NAPA and was told they do not carry it. I checked on line and can not find it . I heard it was a factory oem item and maybe a junk yard . Do you know where I can get one since I am way away from dealer and junk yards.
@sixtyfiveford
11 жыл бұрын
What type/brand of gloves do you wear?
@briansmobile1
11 жыл бұрын
If it's in the budget- yes! If not, no. Lately I've been doing some charity work for people- super low cost stuff, but I don't want to go broke myself.
@angelf9800
6 жыл бұрын
Did have to use Gasket sealer when you put your water pump back on since it was good
@eastpantherbenz
11 жыл бұрын
Is that a ford engine because it said motorcraft on that water pump belt? Thats stupid engieering with that setup. They dont even bother putting a tensioner on it.
@genericusername1365
6 жыл бұрын
Ford and Mazda are related now.
@Jimmynitr
11 жыл бұрын
Once again a great video! Looks like a pain in the ass to do though.
@bicycle697
11 жыл бұрын
Brian, What is your opinion of "Evans - Waterless Coolant"? Saw it on Jay Leno's Garage. Thanks, Rob
@cjfb87
11 жыл бұрын
THANKS BRIAN EVEN THO I AINT HAVE A MAZDA THANKS FOR YOUR VIDS BRO HAVE YOU WORKED ON NISSANS 300ZX Z32
@BRUCECRUZ
7 жыл бұрын
Awesome video, thanks so much for this helpful video. I have the same exact same problem. The same exact stupid part failed on my water pump too. At first, I went to all the parts shop looking for the piece of @#*@# that fail. Nope, dumb stupid engineer won't make or sales just that part. You'll have to buy the whole damn water pump. Damn FORD ("found on road dead"). Just order my part and this video will come in so handy once the part arrive.
@marcbernard7702
5 жыл бұрын
Have you ever thought of doing engineering for all the companies that does dumb stuff or even engineer your own vehicle so it can be mass produced and at the same time affordable while still being competitive to survive? Great info on the video :)
@briansmobile1
11 жыл бұрын
Yes.
@MacThaGoat
5 жыл бұрын
That bottom hose that comes from the water pump that plastic piece can I just buy that are do I have to buy a whole need water pump. Mine literally broke in the same spot. Can I just buy that plastic piece or do I need a whole new water pump
@D6Spanky
11 жыл бұрын
i can only comment on the camera situation... We purchased a new one! I think that you will see a dramatic difference, especially in things close to the camera! We shall see! :D
@tiktokliveencounters9297
11 жыл бұрын
Hey Brian, just curious how long you have been working on cars?
@subaru733
11 жыл бұрын
motor and trans look vary clean how many miles
@briansmobile1
11 жыл бұрын
It is.
@Agropelters
11 жыл бұрын
happy new year!!! and get your rest
@volodymyrnekhoda7017
4 жыл бұрын
I'm wondering how much marijuana had to be smoked to come up with such a complex pump replacement?
@dave1135
11 жыл бұрын
Yep, designed failure. It's made to go out after several years, so the owner will give up and buy a new one. Happy new year brian.
@mrahim826
5 жыл бұрын
Watched 2 other videos that didn't take all this stuff off.
@markn8376
2 жыл бұрын
Those other videos only replaced the pump mechanism. This video shows the pump housing being replaced, because it broke. The same thing happened to my water pump. The only way to fix it is to replace the whole pump housing.
@USSKLEP
6 жыл бұрын
Great Thank You.
@hankwulk3342
11 жыл бұрын
Hey Brian what repair program do you use?
@D4x4Bronc
11 жыл бұрын
ford fullsize trucks are good, crown vic "panther" platform is good. Can say the same for their economy fuel mileage cars.
@briansmobile1
11 жыл бұрын
You have no idea the restraint it takes for me to not to do political videos. Thanks for the feedback!
@marisolsoto6038
6 жыл бұрын
God B. Perfecto
@briansmobile1
11 жыл бұрын
That's because I power washed the sh!t right out of them. ; ) 130K miles. They were absolutely filthy before.
@Mystery207
11 жыл бұрын
OMG thanks for the upload I'm getting real sick of these political videos.
@amezqah
8 жыл бұрын
why not just remove the bolts on the pump and pull it out. i never remove the pump housing on any 3.0 (mvp, tribute, 6, escape) i would say try to remove as little as possible. never had a come back that way. great video.. just my 2 cents
@genericusername1365
6 жыл бұрын
In this case it was the ABS plastic connected to the pump housing that was leaking, so he had to pull the whole assembly out.
@terranoob7523
Жыл бұрын
I feel like you replaced more than just the water pump
@CravinMorehead420
11 жыл бұрын
Had to replace a water pump and radiator on a Ford Escape.. goodtimes.
@borijefedejefes544
3 жыл бұрын
Cuanto valdría un trabajo asi
@hankwulk3342
11 жыл бұрын
You lucky son of a B**** lol I only ask because im a small 800 sq foot shop and work by myself. I worked in a Chevy shop for 10 years and have been working for myself for almost 3 years. Im always asked if I work on imports but as I dont have a repair program I turn down lots of work. Thank you for the reply
@zackwilliamson1129
2 жыл бұрын
Why wouldn’t you show how to put the tensioner pulley back on? Wtf
@briansmobile1
Жыл бұрын
I showed the belt install at 13:26. This one has a spot for a tensioner, but no tensioner pulley etc. It's got an updated stretch belt instead.
@briansmobile1
11 жыл бұрын
7mil Nitrile
@GIGABACHI
6 жыл бұрын
I can't wait to get rid of my 2004 V6. TRULY A P.O.S design . . . built in a way to make you think of changing cars. And no more V6s for me, only tiny straight 4s easier to work on . . . most of the times.
@mattmgarza
4 жыл бұрын
Same on 06 Ford Escape?
@mickblock
11 жыл бұрын
Well someone had to say it.
@TrueBlueEG8
11 жыл бұрын
That has got to be fords engine in that mazda???
@eNKa007
8 жыл бұрын
^5 Brian
@John76546-x
10 жыл бұрын
sorry you hate Fords so much. I have a 2004 jetta tdi that has that black plastic on the thermostat and a few other parts and they recommend replace every time you service along with replace the one time bolts on everything. Also, Ford doesn't require special fluids only available at the dealer.
@John76546-x
9 жыл бұрын
Proper coolant for this vehicle from the factory is G05, not the green stuff.
@BRUCECRUZ
7 жыл бұрын
Thanks for the info, I'm glad you mention it before I start my project.
@D4x4Bronc
11 жыл бұрын
can't
@jcharles1470
10 жыл бұрын
Hi, Brian. Do you have children?
@frankdickman4142
10 жыл бұрын
Hi brians, I have same 2006 mpv, i used your procedure to replace the water pump, but my cam shaft pulley which is driving the water pump belt is giving the squeeking noise. Is my cam shaft pulley gone bad? do you know how can i replace it?
@WhenImGoneCa
11 жыл бұрын
awesome nice video very informative
@incapabledub
11 жыл бұрын
hey brian, you probably already know about this, but my dad got myself and the rest of his guys a really nice rechargable torch (we do alot of crankcase work on large diesels) i should do a tool review really. But i bring this up mainly because it has a UV LED function and its supposed to be for checking leakage from the dye they put in antifreeze. You ever used something like this?
@busancun
7 жыл бұрын
The way you pull out the belt may damage the bolt holding the pump.
Пікірлер: 100