Thank you for video, amazing work!. I have an Astra 1.9 CDTi 120hp Z19DT 2005. Could you tell me the reference of the spare parts? Thanks!. (Sorry, my english is not very good)
@Randiezorzorzor
4 жыл бұрын
awesome video, well done with showing close ups :)
@streetkaaccord344
5 жыл бұрын
Late model 1.9 cdti motors didn't have the lower pulley fitted.
@statorius
3 жыл бұрын
Do you know fro which year? . As i just checked one 2009 and pulley is gone. The place where screw should be it is cleaner than around, so i am guesing it jus fall off, or last mechanic didnot put it back as the belt with tje pulley is clearly too short.
@user-uj8cx3dw3r
Жыл бұрын
You turn the bold right or clockwise to loosen it?
@torsionverole6530
4 жыл бұрын
Good job. I've done it ! See you later alligator. Oliver from France.
@ryans413
4 жыл бұрын
And I thought my car was difficult to do
@leedavies9309
4 жыл бұрын
top job got to do mine in the morning
@trajche_81
7 жыл бұрын
Great job! Thanks again for great video!
@Lacipapa.55
Жыл бұрын
Ha elszakad a szíj útközben ! Hogyan cseréli ki egy hölgy ? Agyon komplikált ,rossz tervezés ! OPEL ASTRA G 1.7 TID az igen!
@1cecold
5 жыл бұрын
this video is so useful. would be much better without the music though.
@MrDen77
3 жыл бұрын
Все ясно и понятно. Спасибо.
@onpointengravingandlaser24
Жыл бұрын
That's a great video well done on that really clear help 👍
@MrCacheiro
4 жыл бұрын
Very good. Thank you.
@barrycarleton1298
2 жыл бұрын
On my mk2 multipla I can get a lot more access than you by removing the right hand wheel and all the plastic covers, dont you have the same with your car?
@milosnikolic9858
2 жыл бұрын
Odlično objašnjeno. Bravo👍👌
@aydanaliev5723
2 жыл бұрын
Hi good job thanks fot the video, is it only possible to change the bearing head, because the whole unit cost 70 euro and i find is kinda expensive and the bearing self is 10 euro
@mrmacczgaming
Жыл бұрын
Full on racist. I live 15minutes up the road from him.
@Robert100CarsRepairs
Ай бұрын
thank you mate, without tools, only spaner, for me was 13
@vazza7504
6 ай бұрын
Thank you for a very clear instructive video. 👍👍👍😎😎😎
@bastiaananthonie
5 жыл бұрын
great video, just changed my belt of an Opel Zafira 1.8 2002 / But after installing and starting the motor is schocking and not running stationair as it did before. My previous new battery died out because when I arrived home I later found out why the batter y died out at my charger belt was gone. The charger belt seems to run oke but the motor is shocking! Does it matter what side you put the grooves on ( i mean the logo of continetal that it needs to go up/down or down/up (does this makes sence. As I am a total no experience with cars. But the car could not be moved due to all the things missing. Anyway I thought changing the belt could be done by a me but now I face a motor that is not running smoothly anymore. Can you give me any suiteble advise reading this. Or does it make no sence. Kind regards, Bastiaan Finland.
@jive091
3 жыл бұрын
Excellent video thanks , but how do you know if your tensioner is broken,? and my old belt snapped , and the pulley wheel underneath the a/c pulley, was tight against the engine and wouldn't move, so we have had to put a washer on it so it will spin, and now it isn't running true and is wearing the new belt out, any ideas, would be much appreciated, thanks
@nicoamstaff4073
3 жыл бұрын
Bonjour est ce que c pareil sur fiat stilo 1.9 jtd 115cv
@jeanpierrealluin5334
4 жыл бұрын
Merci beaucoup!
@АндрейДанилов-м6у
6 жыл бұрын
Very good job! Perfect! Thank you.
@karamurat8629
5 жыл бұрын
when you point the tensioner correct to hole and tighten the tensioner bolt after 2 turns of the crankshaft i noticed that thepointer of the tensioner does not point to the hole anymore has this to because of the tension of the belt after turning it changes
@AndrewPenfold-n8g
11 ай бұрын
Very useful for me thanks
@Jakobthomas1996
11 ай бұрын
Great Video and support 👍
@nebojsaivanovic4311
Жыл бұрын
Great job, tnx
@idrizidriz8951
6 жыл бұрын
thank you...
@joeldavidforteza8830
Жыл бұрын
Great tutorial thank you!
@user-po9sg3ks4p
2 жыл бұрын
Does an alternator tensioner make a type of a noise can you let me know thanks ? If it needs to be replaced
@marksutherland774
2 жыл бұрын
The alternator itself can make a lot of noise when it goes as it uses a clutch system, you'll know when it gone, sounds like the engine is going to give in but it's actually the alternator.
@stjudesjago
11 ай бұрын
Thanks!!!!!
@binduunni703
6 жыл бұрын
Which vehicle is this ?
@fixanddrive
6 жыл бұрын
Bindu Unni Zafira 1.9 z19dt
@LordSandwichII
5 жыл бұрын
Stupid question: You don't need to actually remove the tensioner to swap the belt do you?
@1cecold
5 жыл бұрын
No, you'd be able to swap it only by aligning the tensioner like in 5:53 in the video. Just don't forget to let the tensioner on the belt again :)
@adembajramov3539
5 жыл бұрын
No
@markdyer6570
4 жыл бұрын
Thank you very much from a DIY'er.
@yongzheng2354
4 жыл бұрын
this is great explaining in the video
@neolepel
Жыл бұрын
Спасибо
@andreiduta1065
5 жыл бұрын
Hello.Can i ask you ,is it necessarry to lock the tensioner or not ?
@fixanddrive
5 жыл бұрын
For inexperienced mechanics yes
@orustacres
6 жыл бұрын
good thorough video! Thanks guy
@andreiduta1065
5 жыл бұрын
Can i But the Roller separately from tensioner ?
@streetkaaccord344
5 жыл бұрын
Apparently not, you have to buy the whole thing, even though the pulley unbolts easily.
@sergioruizserelde
5 жыл бұрын
good job
@alexsteini7831
6 жыл бұрын
Grest Job perfect 👍👍👍
@richardgilbert9518
6 жыл бұрын
excellent video, thanks
@traconitide
4 жыл бұрын
Thank you very much!!! But one question, do you know the Nm of other two roller guide? I need this dates for next week. Thank you so much!!!
Пікірлер: 58