Ive been changing trailer brakes, bearings, axles for over 35 years .. this video is the real thing ..thanks for sharing ..well done
@craigerickson1910
2 күн бұрын
Good video, obviously you've done this before. TX for no music! Some dust caps are much harder to remove than how easily yours popped off. If yours is real stubborn, use a small sharp cold chisel between the rib on the dust cap and the edge of the drum hub and tap lightly all around the circle until you get movement. Then tap a flat blade screwdriver in to wedge it out further, finally lay a round shank screwdriver between the rib and the hub and tap with hammer all around until you walk the dust cap off. I agree with others good idea to solder the wires rather than just twist together. Or use a crimp type butt connector. I like your idea to use heat shrink wrap, you always have to remember to put it on before you start the splice. Ask me how I know ha ha. That makes for a good watertight connection. I think the best way to get correct axle nut tightness is to snug up with about 25 lb/ft of torque, then back off one flat on the hex and install the retainer clip or cotter key if so equipped. I have checked this method with a dial indiicator gauge. You should be able to slide the washer around by gently prying with a flat blade screwdriver after assembly. Do this before installing the dust cap. You don't want to tow a trailer with the axle nut too tight, bearing will overheat.
@mikerilee97
49 минут бұрын
Good video for beginners . Simple job & lots are afraid of it . Easier & cheaper than brake shoes & bearing change . Remind people snug that castle nut then back off 1/4 turn or so. And on the wires I think you meant Non - polarized . Ambidextrous means capable of using both hands with equal ease. And solder those wires if possible especially if it’s a marine use trailer 😉
@jayayers2511
26 күн бұрын
Looks straight forward,the only thing I would do differently would be to solder the 2 wires together before the shrink wrap. Thanks
@mikechamplain2425
2 ай бұрын
Super good video...no dumb music, straight forward and great explanation...thank you.
@BeeAmbassador
4 ай бұрын
Great instructional and confidence building video. You even remind me to change my clothes. On a scale of 1- 10, if you're well prepared with paper towels, have a whole box of your 6 mil gloves on hand, Happy to know the names of all the parts. I want to video your video and watch the video while I replace my brakes. :) Thank you, it was clear and well done. Thanks for all the links below, you've done all the research, lowest prices, where you got great customer service, bonus.
@BBCoachBob
4 ай бұрын
Good video, but one thing I would add is the scoring on the inside of the drum is not from worn bearings, it is a normal thing as the magnet is energized it rides on the inside armature of the drum and applies pressure of the brake shoe assembly towards the outside of the drum to apply brakes
@johnmills837
3 ай бұрын
He had gouges not uniform look closer. Drums are ok to use.
@justicetrufaux6722
Ай бұрын
One of the best instructors on YT
@petehoward8494
5 ай бұрын
Highly instructional vid. Great job.
@InterstateAdventures
5 ай бұрын
Thanks!
@roadking6414
4 ай бұрын
Perfect video. I noticed the trailor brake wires on a used 16 ft trailor I purchased have been cut. So, I'll be replacing mine soon. Thanks for the tutorial.
@DF-mb9kc
29 күн бұрын
FANTASTIC INFORMATIVE VIDEO !
@alexdongallo7954
Жыл бұрын
Super Thanks gave me the confidence to do it myself.
@InterstateAdventures
Жыл бұрын
Glad it was helpful for you! Its really not that bad of a project!
@topflightmarketing
2 ай бұрын
Great video. I definitely give this a try next time my travel trailer needs a brake job. Since you used shrink wrap when rewiring the brakes, why didn't you also solder the wires?
@tristanwwsd
Жыл бұрын
Not sure about bearing preload here. Also, pre greased bearings probably aren't Lucas Red so now 2 different greases going on.
@MoragTong_
7 ай бұрын
Agreed. Cranking down on the bearing and calling it good is NOT the way to do it. Probably why dude had bearing issues. Preload your bearing, then loosen the nut...retighten finger tight. Done. I haul granite (12k+ lbs) and run 3000mi a week, never had a single issue with my bearings.
@The57Fordman
10 ай бұрын
I’m surprised you don’t go through the process on how to properly torque the center nut. I can see someone inexperienced tightening the whack out of that nut and burning up there bearings.
@AREA51_ATVSXS_PERFOMANCE
9 ай бұрын
what should the torque for the center nut be ? im currently replacing brakes on mine and when i unstalled it was so lose i didnt know if thats how they are supposed to be ?
@LukeRT
5 ай бұрын
@@AREA51_ATVSXS_PERFOMANCEjust snug , should spin freely but have no wobble left to right or up and down, usually can ve achieved by hand
@mattleach2639
5 ай бұрын
They should also be readjusted after 3-500miles. @@LukeRT
@jeffwiseman0286
5 ай бұрын
I’ve always tightened the nut up as I’m spinning the drum in the opposite direction with a 1/2 drive ratchet. Snug it up tight then loosen about 1/4 turn, spin the drum again and retighten the nut. Back off about a 1/4 turn and install a new cotter key.
@codygriffiths5019
4 ай бұрын
I do that by feel ...
@Donny_Schmidt68
Ай бұрын
Thank you for this!
@sellignomod83
11 ай бұрын
Great stuff. Many Super Thanks!
@InterstateAdventures
11 ай бұрын
Many thanks!
@jesserevilla992
5 ай бұрын
You're a bad ass bro.. Appreciate you man..
@InterstateAdventures
5 ай бұрын
Thank you!
@JavierRivera
2 ай бұрын
Great video. Have you considered disc brakes? I am undecided if I continue with electric brakes or if I switch to disc.
@titush4628
5 ай бұрын
Thank you!
@timandersen7320
4 ай бұрын
Great video, thanks!
@Oldtech51
Жыл бұрын
The Lazy Lube system is the worst thing ever put on a travel trailer. Boat trailer okay. To much grease can cause churning in the bearings. Churning will generate heat. Trailer brake wiring must be connected with crimp on water tight connectors. Never use Scotch Locks. Bearings must have from .001 to .005 inches end play. Never preload a wheel bearing. All wear points on drum brakes must be lubricated at regular intervals.
@bobmartens1089
4 ай бұрын
I've had eazy lube on my Rv for 10 years, I always maintain it, PROPERLY, about 40,000km of trouble free use
@davidjester7228
4 ай бұрын
Timken (tapered) bearings require preload. Better do some homework
@Oldtech51
4 ай бұрын
@@davidjester7228 No preload on final adjustment. Wheel bearings must have end play. .001" to .005". Timken spec.
@vrpeppers
4 ай бұрын
Great video! Need your suggestion and opinion. I have a set of 4 new manually adjusting brakes and 4 new drums on my trailer. When I installed them I realized that both of my axels are covering brakes adjusting wholes.. There is no way to reach it with adjusting tool.. Any suggestions on how to work around it? Would I need to take off the wheels, adjust and put them back to try again?
@xthinker88
5 ай бұрын
Thanks!
@InterstateAdventures
5 ай бұрын
Thank You! I'm glad you found the video helpful
@xthinker88
5 ай бұрын
So. Maybe this is a dumb question. If you bought the drums/hubs pre-greased then why did they take so much grease?
@InterstateAdventures
5 ай бұрын
There is still air pockets after assembly. But it takes a lot less once assembled. I would say maybe a half tube per hub, if that
@nobiwobi100
5 ай бұрын
Thanks
@InterstateAdventures
5 ай бұрын
Thank you!
@garygarcia6020
10 ай бұрын
Thank you
@josevalencia2908
7 ай бұрын
Just heat shrink to hold the wires? 🥴
@InterstateAdventures
7 ай бұрын
Thats how it was from the factory
@thomasgriffin4714
6 ай бұрын
A crimp butt connector with waterproof heat shrink will make a much more reliable connection. I've seen a bunch of bad electrical work from RV manufacturers, so I wouldn't use them as an example of good workmanship.
@billfincher8519
6 ай бұрын
@thomasgriffin4714 Definitely a good butt connector followed by the shrink tubing
@LukeRT
5 ай бұрын
Usually how they come from factory if your lucky to get that much lol
Пікірлер: 59