Great vid. You've got a great voice for surf movie narration. I was all ready for you to say " ..and here's Mike enjoying some leg burning Bruce's Beauties...".
@colinig4411
10 жыл бұрын
best tutorial ever of how to sand a board!!!! Cheers guys
@clintjones9848
4 жыл бұрын
4:45 Absolutely. You can only really start with 220 on production poly boards. Because not only are the lam and hot coat perfectly level, but so is the shape. Don't expect to start with 220 on a home made or epoxy board. Gonna have to start with 80, 100, or 120. Also, don't just machine sand the rails... gotta hand sand. Otherwise you'll end up with a polygonal rail instead of round lol!
@bi0008
2 жыл бұрын
Depends how clean your hot coat is, but probably never 80 grit
@clintjones9848
2 жыл бұрын
I would use 80 grit on my pos home made poly boards, and pro epoxy boards. It's fine as long as you don't put wheel marks in the board. Just a light rough sand then you can finish rough sanding with 120 and it's pretty smooth and ready for lil spot repairs and fine sand. For pro poly boards, I would start with 180 and it would come out epicly smooth.
@anon8730
Жыл бұрын
@@clintjones9848 what are pro poly boards? I'm dutch. Professional polyurethane?
@clintjones9848
Жыл бұрын
Yes, that's what I mean. A professionally made polyurethane board with polyester resin.
@jimmiranda
9 жыл бұрын
I learned a ton of tribal knowledge with this video. Keep em coming!
@paulcombes3782
Ай бұрын
A good sander is as important as a good shaper because the he/she does the last bit of the 'shaping' . Unsung heroes of surfboard production .
@toddrinaldi8447
Жыл бұрын
Can you tell me where I can buy the surfboard polish and the glue that you use for the sanding pads. Also, what polishing pad do you use?
@texsurfer
7 жыл бұрын
would be good to see a vid of sanding a board with channels or a bonzer setup...
@CarScratchRemover
5 жыл бұрын
great video. my world for 25+ years I can't tell you how many videos guys have the pad tipped way too much...but mostly "pro" ding repair guys with zero board building experience. I loved sanding...soooo easy and same piece pay as polishing gloss ... but my real ninja expertise was polishing back in gloss coat days....polishing with a custom built 5000rpm Milwaukee for 5 -6 hours is brutal work.... but I was one of the best in san diego sooooo that's what every factory wanted from me. two of of my signature finishes both polished HC which came out looking just like a polished gloss. OR sanded/polished gloss coat...sand gloss coat starting with 120 then down to 600 an polish.... sealed finish longer lasting with slight reduction in weight over standard polished gloss...i made my own witches brew polish and my own process ...trade secrets.... and job security.
@aidenpaul3784
2 жыл бұрын
This is a sick video
@chrispalmer1255
9 жыл бұрын
Great video! I learned some tips to use on my next build. A light dusting of 3M Super 77 spray adhesive on the sand paper works great on sanding pads with less mess. I have stopped using the Stick-E or Tack-E and won't be going back.
@donotbelieve90percent
9 жыл бұрын
respect, you guys don't get enough..too bad surfboards don't last longer
@jessemartin8512
4 жыл бұрын
Curious about RPMs. What is considered high and low?
@tarekel-sherif1003
3 жыл бұрын
What would be the equivalent finish polish for epoxy sand only finish?
@elvispestana1051
5 жыл бұрын
What makita model are you using in this video? Is it a polisher or an angle sander? Thanks!
@vaughnsigal4560
4 жыл бұрын
Was this board finished with a Hot Coat --> Sanding --> Polish. That is such a nice finish with no gloss coat.
@clintjones9848
4 жыл бұрын
Yep it looks sweet. I also like just leaving the board at 220 or 180. Because it still feels soft but you can grip it without wax and be able to hold onto the board when you're duck diving or whatever.
@carlosruiz8081
8 жыл бұрын
amazing talent!! thanks for share it brother God bless you!!! thanks for your works!!¡
@dominicguay-gosselin3224
Жыл бұрын
Hey what polish do you use? thanks :)
@crowdcontrolinc
9 жыл бұрын
Nice work!
@xwhite2020
10 жыл бұрын
Masterful !
@wbay96
8 жыл бұрын
What's keeping the board on the racks, besides gravity?
@MrNick-
7 жыл бұрын
wbay96 a lot of guys will use tape and you wrap the surfboard rack once, then spin the tape and wrap it more so that the sticky side of the tape faces up for the board to grip to. Obviously use a tape that doesn't leave sticky crap on the board, like blue painters tape.
@chillimiles3710
6 жыл бұрын
no! the video didnt show but before you start sanding get whatever pad your starting with put a 80grit paper on. and quickly skuff up the underside(which is the top of the board) so it sticks to the rack. it doesnt need much just a skim over. if you want to put a gloss coat over the sand dont use tape just in case you leave sticky on it cause problems for yourself. happy sanding
@oschpr
4 жыл бұрын
That rack has piab fc 75 suction cups connected to a foot pedal connected to a gast rotary vane vacuum pump
@scottshapiro5268
4 жыл бұрын
@@oschpr aaaahhhh waht?
@koro287
2 жыл бұрын
@@oschpr As a bare minimum...
@krustysurfer
8 жыл бұрын
What RPMs is he using in the sanded finish run?
@gettinthingsdonemusic9876
5 жыл бұрын
20,000 RPM MINIMUM
@TerrySunnyVision
3 жыл бұрын
Hows the surfboard fixed to the jig like that to make sure it doesnt move when sanding
@tradefat
3 жыл бұрын
It isnt
@johnniehouston1816
2 жыл бұрын
Great music
@alexcorrea1854
8 жыл бұрын
Thanks for the video!! What RPM is the machine set for each grid?
@chillimiles3710
6 жыл бұрын
yes good question feather the trigger around the nose and tail. for pro sanding make sure to keep the speed at 2.5 on flats and 1 on rail
@charleseec35
9 жыл бұрын
What kind of product do you use for the polish? I mean, could you be more precise than "surfboard polish"? Thank you
@krusher74
8 жыл бұрын
+charleseec35 probably an automotive paint cutting compound.
@fiberglasshawaiiTV
8 жыл бұрын
@charleseec35 The product is actually "Fiberglass Hawaii Surfboard Polish" you can find it on our website under "Chemicals & Compunds" shop.fiberglasshawaii.com/shop/chemicals-compounds/polishes-compounds/wcsl-surfboard-polish
@dmac5678
Жыл бұрын
@@fiberglasshawaiiTV No need for rubbing compound before the polish?
@gnrtgamingnewsreviewsandti1286
4 жыл бұрын
any advice on what I am doing wrong- I have sanded to 600 (wet) and can still see some of the sanding marks. I have hand sanded the whole board.
@pearsonmarine5565
3 жыл бұрын
Sometimes the first sanding is key to cutting down scratches. If you didn’t knock down the peaks of the scratch marks with a heavy enough paper to start, you’ll never get those fine scratches to disappear. My advice, stop the 600, and drop back one or two levels of grit to something heavier. Sand thoroughly then work your way back up to 600. If you sit there working your 600 forever, you’ll just start making ash trays in the deck of the board.
@tonyjaii
10 жыл бұрын
what type of sander are those? Model name and number would be great thanks
@olafhenke5654
10 жыл бұрын
it looks like the DeWALT DWP849, it´s an old model. There is a new version that has some nices upgrades. I really like this sander.
@olafhenke5654
10 жыл бұрын
Olaf Henke ... then he grabs a makita and I see a hitachi too. I prefer the dewalt anyways.
@backyardshaper6435
6 жыл бұрын
Thanks, learnt a lot. Consistency is key. Dropping the RPM at the tail too.
@chillimiles3710
6 жыл бұрын
yes feather the trigger around the nose and tail. for pro sanding make sure to keep the speed at 2.5 on flats and 1 on rail
@rpb1961
7 жыл бұрын
why not use an orbital sander for finnish sanding?
@elvispestana1051
5 жыл бұрын
What is the model of the Makita sander?
@rodrigo9015
7 жыл бұрын
I'm wanna be an sander apprentice. So if someone in Australia need one I could be your buddy!
@310inc5
5 жыл бұрын
Thanks so much to video so sick
@bphillips06
2 жыл бұрын
Where would one find "surfboard polish" .
@hazwaz6385
5 жыл бұрын
is the sander rondom orbital or orbital
@harryzanini
3 жыл бұрын
they're called "rotary" polisher/sander. you want a "variable speed" version so you can slow down the speed. also the sanding pads are "flexpad" , a good all around choice is the 8 inch red clothface medium with 5/8 in threads.
@mattholland31
4 жыл бұрын
epoxy or polyester resin on the board??
@clintjones9848
4 жыл бұрын
Polyester. You can't start with a grit as fine as 220 to sand an epoxy hot coat.
@jargarcia9162
7 жыл бұрын
What kind of surfboard polish is that?
@chillimiles3710
6 жыл бұрын
its this hi tech stuff called your mums lube
@bodasafahaualii5264
9 жыл бұрын
3/8" Concave Concave Concave Fish!!
@asesurfschool
9 жыл бұрын
how much Its pay for a sand/polish job?!
@olabashanda
3 жыл бұрын
don’t you get itchy fiberglass all over your arms?!?!
@HighFlyer61488
8 жыл бұрын
Don't mind the edges
@elinasmith8258
5 жыл бұрын
If your doing the whole board process your self and its a one off. I suggest you hand sand the rails unless you are not worried about thru. Oh what a lot of crap I hear a with a sharp intakes of breath. Every one has an opinion . Trust me unless you trip off to ibiza every second month on a cafe del mar sunrise. I have all beit at least a thousand boards and work exclusively on exceptional high end racing craft. Just have fun.
Пікірлер: 65