Interesting, what has happened to the airend, was it stuck
@BDFactoryEngineer
Ай бұрын
Yes, it stuck 😔
@عليسليمان-ق2ج
10 ай бұрын
ممتاز جدا لاكن اخي قمنا باصلاح ضاغط حلزوني كما فعلتم انتم تماما. ولاكن عندما اعدناه لتشغيل اشتعل في بداية الامر بضع دقائق ثم توقف فجأه وعندما اعدنا فكه وجدنا انا السكرو قد تأكل مع الجسم
@BDFactoryEngineer
10 ай бұрын
يمكنك مراسلتي على صفحتي في الفيسبوك. facebook.com/bdfactoryengineer/
@mohamedalzway8644
6 ай бұрын
you need to set the clearance between the screws and the bearings house .because when the compressor works it get expanded
@mohamedalzway8644
6 ай бұрын
you need to set the clearance between the screws and the bearings house .because when the compressor works it get expanded
@shaikhshohrab
11 ай бұрын
Can plz share main compartment of screw compressor? Why we are using oil in compressor
@dimaivanov2275
11 ай бұрын
После такого ремонта блок может умереть навсегда. Нельзя так перебирать
@AjayKumar-mb1jd
Жыл бұрын
Sir Atlas copco screw compressor Mai element temperature jayda ho jata hai shut down.band high temperature please
@BDFactoryEngineer
Жыл бұрын
Please massage in my Facebook page
@AjayKumar-mb1jd
Жыл бұрын
Sir ok
@AjayKumar-mb1jd
Жыл бұрын
@@BDFactoryEngineer sir Facebook I'd please send me
@AjayKumar-mb1jd
Жыл бұрын
@@BDFactoryEngineer send me Facebook I'd
@BDFactoryEngineer
Жыл бұрын
facebook.com/bdfactoryengineer/
@AhmedMostafa-di2cg
5 ай бұрын
السلام عليكم .لماذا البيرنج الاخير ركب بالاتجاة المعاكس له ؟ارجو الشرح والتوضيح
@TritonChannelTV
11 ай бұрын
What is the paste or gel put in the bearing cover?
@BDFactoryEngineer
11 ай бұрын
yes brother It is RTV glue
@SUNILMABEN-e8d
11 ай бұрын
Good job but must be use more tools... But good job. Keep it up!
@BDFactoryEngineer
11 ай бұрын
Thank you so much for your comment ❤️❤️👍
@hammothw4814
Жыл бұрын
what is your trade, millwright...or mechanic?
@locosporlasmaquinas
11 ай бұрын
Lo rodamientos axiales están colocados alreves
@BDFactoryEngineer
11 ай бұрын
Please tell me English
@SS-fw1dd
Жыл бұрын
Thanks for sharing such a valuable insights in bearings replacement, any clearances or shims needed, precautions to be followed in other video.
@BDFactoryEngineer
Жыл бұрын
Thank you ❤️
@AjayKumar-mb1jd
Жыл бұрын
@@BDFactoryEngineer please give me mobile number send me mobile number 🙏🙏🙏
@elementclinic6915
8 ай бұрын
I think you fixing angular contact bearing wrong position
@BDFactoryEngineer
8 ай бұрын
Really? But it's Properly Running.... Almost 4500 Hours.
@MDFoysal-pu7cm
Жыл бұрын
nice
@BDFactoryEngineer
Жыл бұрын
Thanks
@wowiecaps
2 ай бұрын
please see in your vid that you place the thrust bearings in the wrong way. this air end will fail with in 10 seconds.
@BDFactoryEngineer
2 ай бұрын
Ok I'll see, thank you for commenting. But it didn't happen.
Пікірлер: 36