very easy to follow and precise guide, I was able to communicate with the VFD with a WinAC RTX soft plc in no time!
@bernardshawgeorge7910
10 ай бұрын
Hello, why don't you see the Profinet message type selection parameters in the inverter? Is it ok to configure PPO only in the SIEMENS TIA Portal?
@schneiderelectric
10 ай бұрын
Thank you for your message Bernard. We house most of our documentation in a virtual database here: spr.ly/6050uqKls. If this does not address your concerns, please reach out to a technical support person in your location. spr.ly/6051uqKlt
@MihajaAndrianarivony
7 күн бұрын
Hello, If iwant to use telegram 106 what is the parameter?
@schneiderelectric
7 күн бұрын
Thank you for your message. We house most of our documentation in a virtual database here: www.se.com/ww/en/download/. If this does not address your concerns, please reach out to a technical support person in your location.www.se.com/ww/en/work/support/country-selector/contact-us.jsp
@hetanhawke2354
2 жыл бұрын
Thanks
@nestorparades4525
2 жыл бұрын
Dear I want to communicate an S7-1500 PLC with several Altivar 320 and 630 drives. Could you help me with a guide?
@lucaswiniciusdasilva5293
2 жыл бұрын
with Profinet?
@RahulKumar-tt8ou
2 жыл бұрын
@@lucaswiniciusdasilva5293 ON ETHERNET IP
@chin1209
2 жыл бұрын
HI , I WANT TO do communication Siemens S7400-H via on board MODBUS TCP , can i use onboard Ethernet/Modbus TCP Port ?? please guide my drive is ATV930
@schneiderelectric
2 жыл бұрын
Thank you for your message, chintan bhavsar. We apologize for any inconvenience caused. For technical support or to find answers to your questions, please refer to our support center: www.se.com/ww/en/work/support/support-center.jsp
@jkhela
Жыл бұрын
Very Good Video! not that i can start and stop it. What about how to set the direction Rev/Fwd? Fault Reset? Current Warnings/Fault? We just purchased 8 more so any help would be appreciated, Thank you
@schneiderelectric
Жыл бұрын
Thank you for your message, Karm Khela. We apologize for any inconvenience caused. For technical support or to find answers to your questions, please refer to our support center: www.se.com/ww/en/work/support/support-center.jsp or reach out to a technical expert in your location here: www.se.com/ww/en/work/support/country-selector/contact-us.jsp
@jkhela
Жыл бұрын
@@schneiderelectric I have and no one seems to know!
@jkhela
Жыл бұрын
The manuals to not specify the inputs and outputs i am looking for.
@schneiderelectric
Жыл бұрын
Hi Karm! Thank you for contacting APC by Schneider Electric. Please be advised that your concern has been endorsed to our Drives Team. They will assist you further with your concern. Kind Regards, Jurvy
@jkhela
Жыл бұрын
@@schneiderelectric no one has contacted me yet
@mdmehedi8912
2 жыл бұрын
please send me, hexcode parameter siemens to schneider profinet communication
@schneiderelectric
2 жыл бұрын
Thank you for your message. For technical support or to find answers to your questions, please refer to our support center: spr.ly/6059K84ZT.
@mdmehedi8912
2 жыл бұрын
@@schneiderelectric, please communicates youn with them,
@schneiderelectric
2 жыл бұрын
Thank you again for reaching out. We are unsure of what you are inquiring about. For direct assistance, please reach out to a technical expert in your location here: spr.ly/6057KDeXv
Пікірлер: 23