how do i connect a rudder preset to switch (DX 6e). I had no probs when setting up different elevator angles for different flight phases on a switch (flap adjustment) - but cant manage to attach the rudder....
@tariqyounus3880
Жыл бұрын
Do u have any video with radio master t16, how to make settings all of these ?? I going set my radio master t16 for my first flight ??
@RCPlaneAddict
3 жыл бұрын
Thanks for this. I got a good 5 minutes of gliding on my maiden, but now that it is dialed in, I am going to try some of your set ups.
@mendobry
Жыл бұрын
Where to buy this disc launch glider?
@DorinJacota
2 жыл бұрын
I'm looking to get a glider, but I'm concerned about radio transmitter power / distance. I wish to avoid to loose the glider due to radio transmitter's capability. At what altitude do you estimate that the glider can climb? I'm thinking to get a DX 6e. What would you advice?
@TimmyRC
2 жыл бұрын
For gliders of this size you generally will be more concerned with losing sight of it before being concerned with losing signal. Pretty much any brand/protocol will be good enough. Spektrum doesn't have the best range in the industry, but it works just fine for DLGs.
@deqzo
3 жыл бұрын
What a Recipient do you have ?
@yz3601
Жыл бұрын
Does the snapflap adds on top of the differential? so when you turn and pull a bit the stick, doesn't it adds too much flap down movement?
@TimmyRC
Жыл бұрын
Yes, they add. No, it's not too much, especially since you should be doing most of the turning with the rudder.
@NickSmith-hv9zi
5 жыл бұрын
Nice walk through the settings but unsure about your differentials setup and like to ask. To compensate for adverse yaw, where the down elevator surface create more drag, as you said you typically configure less down and more up. In your situation, you will need to compensate some other way, perhaps up elevator . Otherwise the turns would be uncoordinated with nose pointing outward of the turn. I've had the exact setup and the result was quite high rate of up elevator to sustain the turn as well as ruder mixing. Also another problem is generally with very high flaps, you need delay. That is because as soon as you enable the flaps, nose comes up, before air catches the stabilizer to compensate the mixing. The fix is push the nose down a bit then enable flaps. I can never figure out how to mix delay into an already mixed channels.
@TimmyRC
5 жыл бұрын
For flaperon differential, you should not use so much so that the plane suffers from an excessive amount of adverse yaw. In addition, proper gliding technique is to turn mostly with the rudder in order to maintain the efficiency of the wing. Also, airplanes generally need up elevator in a turn regardless of their differential. You do not need an elevator delay on a flaperon elevator mix. There is no point at which you are waiting for the stabilizer to "catch" the air; The stabilizer constantly has air flowing around it during flaperon deployment, so any stabilizer inputs will take effect immediately. I think the effect you are describing is when the whole airplane rises suddenly when the flaperons are deployed quickly, which is due to the airfoil's shape changing dramatically when the airplane is still traveling at a relatively high airspeed. So the amount of stabilizer correction would ideally be proportional to airspeed.
@yuratretiakov6734
2 жыл бұрын
Good video! I have DLG with DX8 last ver3.01, i do not understand how to activate throttle stick for sailplane model, would you please advise me how to do that or may be you can share your model copy file for uploading, Thank you
@lucywucyyy
2 жыл бұрын
id mix in some rudder to counteract the adverse yaw of the ailerons
@TimmyRC
2 жыл бұрын
You could, but in my experience I haven't been able to notice any adverse yaw with DLGs except when using the flaperons. Maybe it's more noticable with other types of gliders.
@1988dirk
4 жыл бұрын
Hey, Is there no need to mix some elevator in your presets? E.g. If I change into thermal mode i have to mix some elevator down into it so that the plane doesn‘t lift the the nose and slows down until it stops.
@TimmyRC
4 жыл бұрын
Yes, often times you need mix elevator into the presets to keep the plane flying level to adjust for the camber changes.
@ikeimage
Жыл бұрын
Be sure to mix in some down elevator with ur full flaps or brakes to help with nose pitch up
@goldenfish77
2 жыл бұрын
I saw Your this video several times but now I just want to setup my homemade "Snipe" clone DLG by Your setup. So I thank You for these great explanations!
@TimmyRC
2 жыл бұрын
Thanks!
@w.j.bendellr.c.flying.1037
2 жыл бұрын
Thanks I needed that, i’m setting up my glider for the first time. ⭐️⭐️⭐️⭐️⭐️
@rapharigoti
Жыл бұрын
Thanks for sharing Timmy!!
@fibiger12
Жыл бұрын
i would love to see how you set the parameters on the controller
@cobratec31
2 жыл бұрын
Would be a lot better if you show how to set up all these modes
@andipower8163
3 жыл бұрын
I'm new to DLG and this helped me a lot to understand the different flight modes.
@ChristieNel
3 жыл бұрын
When you say 40% differential, do you mean down is 140% of up or that up is 40% of down?
@TimmyRC
3 жыл бұрын
Up is 40% less than down. This means up is 60% of down, or down is 167% of up.
@ChristieNel
3 жыл бұрын
@@TimmyRC Perfect, thanks.
@neilglick7027
3 жыл бұрын
Love your video. It's the clearest I've watched explaining flight modes for gliding. Thanks for posting.
@TimmyRC
3 жыл бұрын
Thanks!
@warrenfromga9945
Жыл бұрын
This video is very helpful to this glider newbie. Thank you.
@TimmyRC
Жыл бұрын
Thanks!
@kev4354
2 жыл бұрын
Good informative Tutorial - Thanks
@TimmyRC
2 жыл бұрын
Thanks!
@magneresjuan
4 жыл бұрын
great video and nice plane !!! which airfoil do you recommend to build a dlg bagged wing? Im about to start building one but don´t know wich should I pick
@TimmyRC
4 жыл бұрын
Thanks! I would say the Zone V2, but it is probably outdated at this point since it came out in 2011. I am not up to date with publicly available DLG airfoils.
@tonyrobinson3744
3 жыл бұрын
Great video! I've been trying to figure this out for quite awhile. Thanks Timmy! Great vid. I have the 1 meter mini dart from Soaring models I can't wait to try to apply this to.
@TimmyRC
3 жыл бұрын
Thanks!
@RCSoaringDiaries
3 жыл бұрын
I'm getting more and more into gliders and found this info excellent - thanks for posting it 👍
@TimmyRC
3 жыл бұрын
Thanks!
@Themandogable
3 жыл бұрын
Do you have a video on setting up all of that on the transmitter? like a walk through?
@TimmyRC
3 жыл бұрын
I do not. It changes depending on the transmitter.
@biophillie
3 жыл бұрын
Outstanding video.. You should consider being a teacher if you're not already.
@TimmyRC
3 жыл бұрын
Thanks!
@alpinat0rsflyingadventures413
3 жыл бұрын
I'll second that
@conradtaggart9959
4 жыл бұрын
Good but would have been better, actually excellent, with some measurements given for each mode as you can't really see what is happening with the surfaces and have little idea of the relative movements
@TimmyRC
4 жыл бұрын
Thanks! The amount of deflection needed changes from model to model and should be determined experimentally, so I didn't bother providing measurements.
@williamramey4739
4 жыл бұрын
I am a newbie. I have a sail plane with throttle, rudder and elevator. Should I keep throttle and rudder on the left stick and elevator on the right stick? At this time, I have elevator and rudder on the right stick and throttle on the left stick. Thank you to anyone that can help me.
@TimmyRC
4 жыл бұрын
Typically the rudder is on the right stick for your kind of airplane (assuming mode 2).
@williamramey4739
4 жыл бұрын
@@TimmyRC Thank you. Yes, I have the DX 6 on mode 2. I appreciate your very quick response. I am watching your videos about sail planes and I am learning a lot. Thank you for both your reply and your videos! I thought that I might have changed a default by accident. I am learning on the Night Radian. My next plane will be the Conscendo Advanced with ailerons.
@billwelling9221
4 жыл бұрын
enjoyed your video. would be interest also on a video on set up for Dx8.
@TimmyRC
4 жыл бұрын
Thanks!
@MissurayLaslo
5 жыл бұрын
Nice explain,,,,int. elv ail mix 🤘i will try if buy dlg
@TimmyRC
5 жыл бұрын
Thanks!
@ctingermann9365
4 жыл бұрын
I am new to sailplanes and gliders. These are very informative. Appreciate the time taken to create the videos.
@TimmyRC
4 жыл бұрын
Thanks!
@alpenjon
3 жыл бұрын
Very instructive, thank you!
@TimmyRC
3 жыл бұрын
Thanks!
@jdouglasj2000
3 жыл бұрын
I am trying to figure out if I would enjoy this or not. I like flying my Night Radian and my Conscendo, but it can get boring after a while because you just power up, get to altitude and cruise around. Watching gliders on video is boring, but I suspect the thermal hunting would be fun. I would be curious to hear how you rank DLG flying compared to your favorite prop planes and electric gliders.
@TimmyRC
3 жыл бұрын
DLGs are my favorite fixed wing aircraft I've flown. They don't require a fancy launch system, they can be flown at very small fields, and they fly for hours on a charge. Competition-grade DLGs are highly engineered, high performance machines (unlike a Radian), and those kinds of machines are always more fun to pilot. There is also something satisfying about flying under your own power, and hunting for thermals without a motor is a fun challenge.
@jdouglasj2000
3 жыл бұрын
@@TimmyRC Thank you. Okay so you enjoy DLG's even more than a $2k 3M powered glider? Could you say something about the recommended skill and experience levels (really two different things...most of my crashes have been a result of low experience and not low skill). I am new to RC (1 year). I can fly my Conscendo, Radian, Turbo Timber, UMX TT, etc. all just fine. But boy, I don't want to crash a Snipe. Oh, and can you recommended a particular DLG to me? All I really know about what I want is that I think bigger is better.
@TimmyRC
3 жыл бұрын
@@jdouglasj2000 I have never flown a high end 3m glider, so I can't speak to that. However, with a large powered glider you lose the small-field-flying capability, the fun hand launch, motorless gliding purity, some aerobatic capability, and some of the challenge of thermalling. My closest point of reference is a powered Bird of Time, which I just don't find as fun as DLGs for the aforementioned reasons. If you are already proficient at flying fixed wing you shouldn't have much trouble transitioning to a DLG. Due to F3K rules, all competition-grade DLGs are 1.5m. You will get the best performance with a 1.5m competition model such as a Snipe 2 or BAMF 2. However, I constantly recommend the 1m Armsoar Deviant for beginners since it has the same construction as competition models, but is smaller, making it easier to launch, slightly more durable, and less expensive. You can also try to pick up a used or unbuilt competition model from the RCGroups classifieds. I got my Snipe as an unbuilt kit through RCGroups and saved a few hundred dollars.
@jdouglasj2000
3 жыл бұрын
@@TimmyRC Very helpful. Thank you so much.
@luke_atthat
4 жыл бұрын
Nice explanation and demonstration
@TimmyRC
4 жыл бұрын
Thanks!
@ChristieNel
3 жыл бұрын
I note that you don't have any camber to elevator mix. How do you prevent your Snipe from pitching up when you increase camber? Just manual elevator?
@TimmyRC
3 жыл бұрын
I have slight changes in elevator programmed for the different flight modes to maintain level flight. However, for flaperon functionality I do not use an elevator mix. For my setup, I have found that the amount of down elevator needed to maintain pitch is highly dependent on airspeed when the flaps are applied. Therefore, an elevator mix will apply the wrong amount of elevator most of the time since it cannot react to changes in airspeed, so I personally find it easiest to omit the elevator mix altogether.
@ChristieNel
3 жыл бұрын
@@TimmyRC Yes, this is all true. What I found helps is to program a mode change delay on the camber, i.e. the camber changes slowly between modes - this reduces the nose up behaviour as it naturally slows down as the flaps increase. But I still find that the final angle of attack changes more than I'd like and I don't want to add mix. I'm wondering how much the CG is affecting this. I have a Strike 3.
@TimmyRC
3 жыл бұрын
@@ChristieNel I have my flaperons on the throttle stick, which I find useful since I can apply the flaps at whatever speed I want and however much I want. The amount of pitching that occurs with application of flaps changes depending on the airplane. I can't find anything definitive about the CG's effect, but I suspect there might be some relationship since changing the CG location changes the sensitivity of the elevator.
@ChristieNel
3 жыл бұрын
@@TimmyRC I have some amount of flaps on my throttle stick in cruise mode only. I'm finding it annoying having to switch to landing mode to get full flaps down, so considering a lot more flaps on my throttle stick, with perhaps a very strong exponential. How do you brake?
@TimmyRC
3 жыл бұрын
@@ChristieNel I have full flaps available via the throttle stick in all flight modes except launch mode so that I do not have to change flight modes to brake. I do not use expo.
@hunterfpv4272
5 жыл бұрын
Good👍👍👍
@TimmyRC
5 жыл бұрын
Thanks!
@magneresjuan
4 жыл бұрын
great video, which receiver you use? and wich battery do you recomend? Thanks
@TimmyRC
4 жыл бұрын
Thanks! I use a LemonRX 6ch diversity receiver and a 600mAh 1S LiPo.
@MontyMontemayor
4 жыл бұрын
@@TimmyRC do you use any BEC to regulate the voltage or your electronics are directly powered by 1S Lipo?
@TimmyRC
4 жыл бұрын
@@MontyMontemayor It is direct 1S power. You have to make sure the receiver and servos are rated for the low voltage to avoid losing control. Also, there is no over discharging protection, so it is a good idea to run a receiver with voltage telemetry.
@yeahitworks
4 жыл бұрын
@@TimmyRC can you please share the servos that you use? Thanks
@TimmyRC
4 жыл бұрын
@@yeahitworks Dymond D60s for flaperons and Dymond D45s for tail surfaces. They used to be the gold standard, but there are better glider servos nowadays.
@yodaiam1000
5 жыл бұрын
It would be good to have another video with your programming steps. Especially on the DX8. Thanks for the video.
@TimmyRC
5 жыл бұрын
Thanks! I purposely left that part out for this video since each transmitter is different. However, I can definitely go over the process on my DX8 if there's enough interest.
@yodaiam1000
5 жыл бұрын
@@TimmyRC To be honest, I am kind of self interested since I have the same transmitter. Having given full disclosure on that account, I still think it is a good idea to do a video. If you can program a DX8 G1, the newer transmitters (I suspect) are easier to program so it may translate.
@MrPauoa
4 жыл бұрын
@@TimmyRC Thank you Timmy, I would be interested, I am picking up a DX9 and just getting into DLG's
@paulgross4789
4 жыл бұрын
Yes, please. You're explanations are really clear and easy to understand. Plus, I have a DX 8 as well...so...
@MontyMontemayor
4 жыл бұрын
Interested in this as well and would like to know you pick a specific switch over the other and if you are using a dial to dynamically tune.
@bohan9957
4 жыл бұрын
What happens when you deploy full flaps, then operate the aileron?
@TimmyRC
4 жыл бұрын
The ailerons become pretty ineffective at controlling roll with full flaps deployed. Adverse yaw is common in this situation. Therefore, it is best to steer with the rudder when full flaps are deployed.
@bohan9957
4 жыл бұрын
@@TimmyRC Got it, thanks for the explanation. Also for thermal mode, do you mix in any rudder with the aileron to aid the turn?
@TimmyRC
4 жыл бұрын
@@bohan9957 Yes, generally you want to steer with the rudder as much as possible so that the wing's airfoil maintains maximum efficiency. However, I do not use a rudder and aileron mix in the transmitter.
@bohan9957
4 жыл бұрын
@@TimmyRC Again, very helpful information. Thank you! Subscribed!
@TimmyRC
4 жыл бұрын
@@bohan9957 Thanks!
@joevangorder1006
5 жыл бұрын
Thank you for posting this!! Your videos are the most helpful I've found and I'm sick of those cop out statements like "start with 1 flight mode and go from there" or "each planes settings will be different" .... got it..😡. An example like this goes a LONG way for a starting point to get people flying but they are guarded like military intelligence. Thanks for taking the time
@TimmyRC
5 жыл бұрын
Thanks!
@claywedgemore7665
5 жыл бұрын
Timmy Rc, thank You for posting your video. Very nicely done and informative! Jb
@TimmyRC
5 жыл бұрын
@@claywedgemore7665 Thanks!
@mikalnuelle
3 жыл бұрын
Great video. Very informative. What would be a really good follow up video is how to actually set these flight modes up indifferent radios. I'm having trouble figuring it out in a DX8 and a DX9
@chris-adams-tas
5 жыл бұрын
Mis-information alert. For thermalling more up flapperon deflection is best; down-going surfaces are draggier and induce adverse yaw. en.wikipedia.org/wiki/Adverse_yaw Scroll down to Differential aileron deflection.
@miksterr
4 жыл бұрын
No. Read it again. These are 2 different thing. Adverse yaw/ differential is a behaviour of yaw induced by ailerons during a roll. Both ailerons down (flapperons) as no seperate flaps on these dlg’s is the method to increase lift whilst in a thermal.
Пікірлер: 101