Thanks, gave me exactly the information I was looking for 👍
@GBWM_CNC
2 жыл бұрын
Great to hear!
@umargul5644
Жыл бұрын
Great job sir thanks a lot, your video solved ❤my pwm based😢 frequency spindle operating issues...god bless you ❤❤❤❤❤❤❤
@GBWM_CNC
Жыл бұрын
I'm glad my video helped you 😊
@tolgaamedov1922
10 ай бұрын
Thank you so much for this video!
@GBWM_CNC
10 ай бұрын
you're welcome!
@sociedadeausente6209
8 ай бұрын
Obrigado ajudou muito , FELICIDADES
@Jur4S
7 ай бұрын
i would love to see same proces on linux cnc. Its much harder and a lot of peoples using same cnc bob as you with linux.
@GBWM_CNC
7 ай бұрын
I made some time ago a video about linuxcnc configuration on my cnc lathe basis. It's a bit less quality than my recent videos but there's all you need to configure what you need. The VFD setup is exactly the same as for mach3. Link below. kzitem.info/news/bejne/s3-a1KabnXpljKg
@TrPrecisionMachining
3 жыл бұрын
good job
@GBWM_CNC
3 жыл бұрын
Thank you! 😁
@holikarbon
Жыл бұрын
Thank you.
@GBWM_CNC
Жыл бұрын
You're welcome
@johnprandoni
5 ай бұрын
Grazie
@GBWM_CNC
5 ай бұрын
💪
@ahmedgerza1753
3 жыл бұрын
Very good
@umargul5644
2 жыл бұрын
Great 👍
@niksechtniks
3 жыл бұрын
Tnx ur a champ!
@GBWM_CNC
3 жыл бұрын
I'm glad I could help. I hope you enjoy! 😁
@DvuongDo
Жыл бұрын
Pro!
@valneimontoro575
6 ай бұрын
Good afternoon friend, I have a SAKO SKI780 single-phase 220V inverter for a 2 CV Spindle on the RNR on an Ecomotion Masch 3 board and I am not able to configure the parameterization on the inverter, can you help me solve this problem?
@GBWM_CNC
6 ай бұрын
Hello! The configuration should be similar to what you see here. If you need more information about rnr ecomotion check out my video where I showed H100-2.2T4 vfd setup. There was somebody in the comment section who gave info about how to setup the vfd with RNR board.
@jbb1633
2 жыл бұрын
Good day sir can you teach me how to connect it to my szgh control. Thanks
@GBWM_CNC
2 жыл бұрын
Sorry, i have no experience with szgh controllers
@themartensway8082
2 жыл бұрын
Can you leave a link to all items used in video please
@GBWM_CNC
2 жыл бұрын
VFD - Sako SKI780 (can be found on aliexpress) Motor - 2.2kW 400V 50Hz (bought used from local ebay) Breakout board (the one connected to pc) is the cheapest parallel CNC breakout board available on aliexpress The power module and transformer are just to make 12VDC out of 230V AC (I had those lying around) - you can use any 12VDC power supply instead (the breakout board needs 12V input in order to work properly)
@themartensway8082
2 жыл бұрын
Thanks a bunch
@cr2fabrication
3 жыл бұрын
I have the same mach3 board, can you get reverse out of it?
@GBWM_CNC
3 жыл бұрын
Do you mean reverse spindle rotation signal (M4 command)?
@cr2fabrication
3 жыл бұрын
@@GBWM_CNC Yes, I believe you would need another relay...
@GBWM_CNC
3 жыл бұрын
@@cr2fabrication Exactly.
@msanguyu
Жыл бұрын
Hello. Can you connect this vfd via rs485 to usb adapter?
@GBWM_CNC
Жыл бұрын
No idea tbh
@ar-roihanchannel7255
2 жыл бұрын
I have huanyang vfd which one that i must connect to my paralel breakout board?
@GBWM_CNC
2 жыл бұрын
Could you explain? I don't understand
@ar-roihanchannel7255
2 жыл бұрын
@@GBWM_CNC i want to control speed of spindle using mach3. Can you explain what port of vfd (acm,dcm,for etc) which is i must connect to breakout board?
@GBWM_CNC
2 жыл бұрын
@@ar-roihanchannel7255 I have never had a hyanyang VFD so I can't tell you but you will need to find in the manual where to connect forward run command signal and use the relay outputs as on the video and find the analog inputs on the vfd and feed in those the analog signal from the parallel board. I think if you find a wiring diagram you should do well
@ภัทรเชนทร์รามคง-ฉ7ฏ
Жыл бұрын
Can it be used with cnc red board?
@GBWM_CNC
Жыл бұрын
Why would you use both?
@zamanraza9635
Жыл бұрын
Hello bro how's you ? I am using same breakout board as you are using .but when I click on spindle start the relay on board does not click (no sound of tik) .can you tell me what's wrong with it ?
@GBWM_CNC
Жыл бұрын
check with a multimeter if there is the right voltage on the output of the relay coil input
@zamanraza9635
Жыл бұрын
Bro it does not show any voltage on multimeter. I have checked so many times
@GBWM_CNC
Жыл бұрын
@@zamanraza9635 Well. Then there is something with the configuration or the board wiring or the board is damaged. Hard to tell remotely bro
@zamanraza9635
Жыл бұрын
I have made all correct setting according to your video . But when remove parallel port cable and reattach it to board then the relay click the tik sound. Don't know what's the problem
@GBWM_CNC
Жыл бұрын
@@zamanraza9635 Have you connected both the USB and parallel cable (and all power supplies?) ? I had similar problems when I forget to connect the USB cable I think. If this is not the case - I dont know. It worked always fine for me
@cr2fabrication
3 жыл бұрын
Uruguayan?
@GBWM_CNC
3 жыл бұрын
No sir
@cr2fabrication
3 жыл бұрын
@@GBWM_CNC I saw the Mate in the beginning, my wife is from Uruguay...
@GBWM_CNC
3 жыл бұрын
@@cr2fabrication I am from Poland, but I love mate 😁
@cr2fabrication
3 жыл бұрын
@@GBWM_CNC You fooled us both!!! God Bless!!! Great video.. Trying to decide either a servo with VFD or straight 3 phase motor like yours..
@GBWM_CNC
3 жыл бұрын
@@cr2fabrication haha! 😅😅 There are many factors to take under consideration. But I think the main reasons to take a servo for spindle drive is the ability to "clamp" the shaft by using a control signal, they're usually lighter than usual 3 phase motors in the same power range and there are many ways to control the motor. But if the price matters then the standard 3 phase motors might be the way to go.
@jantatarski5716
Жыл бұрын
Gówno widać
@GBWM_CNC
Жыл бұрын
Ja nie widzę, proszę przetrzeć wyświetlacz :)
@jbb1633
2 жыл бұрын
Hi sir donyou have an email address? Maybe you can help me with my problem. Tnx.
Пікірлер: 58