This is the only video i've found talking about this. Thanks for the help!
@babatundefajemisin8221
Жыл бұрын
I mixed with those your line arrays of yours last month and the experience was awesome.
@DTheoplis
3 жыл бұрын
Thanks for sharing this, this makes things a ton easier!
@markwinsock3919
2 жыл бұрын
Thanks for making it easy. Best video I seen on this. 👍👍👍
@jaroslavbahurinsky111
4 жыл бұрын
Thank you, you were the first to show it.
@jshi600
4 жыл бұрын
Thanks,we are trying to get out videos that can really help not just overviews! Please Subscribe if you haven’t already.
@OrlandoReyessonido
4 жыл бұрын
Jason Robinson , thanks for that video, for 5 days i was wondering how to do that since i use P16 a lot 😎
@jshi600
4 жыл бұрын
No problem Orlando Sounds happy that the video could help you! That’s what we make them for!
@CarlsOpinion
3 жыл бұрын
@@jshi600 Thanks I just Sub'd. I was worried, since Sweetwater seemed to indicate that you could only route it through the SD stagebox or an x32 mixer and NOT an S-16 or an S-32 stagebox. Looks like it works through the S-16. Thanks again. Carl
@lucasbatalhaguimaraes7464
3 жыл бұрын
Good night, I would need to use two AES 50, 1 port to send signals to another wing on the PA, and the other port to send signals to another wing in a broadcast studio, the table that would receive the physical channels would be the monitor, even using the two aes 50, do you still have more ports? because I would need one more to send to my p16 switch.
@davidduncan1938
3 жыл бұрын
Great video, thanks. What if we want to add iQ15 and iq15b PA via ultranet? Can this be done somehow with the pm16 and pm16 distributor? We have a wing and a Midas 32 stage box. Thanks again
@Jb33311
2 жыл бұрын
Hey bro thank you for your videos. Quick question how do I send post processing from a single channel to the p-16. Without taking up another bus channel just for ears?
@markwinsock3919
2 жыл бұрын
When using the P16 is there a way to run the output of the P16 to wireless IEM’s without running chords back from the output jacks? Thx….wasnt sure if you could route back from the P16.
@moisesquirinojr.8856
3 жыл бұрын
Thank you just got it and this was short simple
@jshi600
3 жыл бұрын
Moises Quirino Jr. Thank you please subscribe
@davidhanson9280
2 жыл бұрын
Where did you get those labels you have on the p16?
@thomasfoster4091
Жыл бұрын
Alright but is that signal post fader or from the tap point? Can’t figure out how to send my busses to the mixer from the tap point. I’ve been trying to rout all my p-16 channels through the “user signal” channels so that I can choose to send the channel or buss from the tap point. This works for single channels, but when I do it for a bus (like my vocal fx, or instrument reverb I get no signal out to the p-16. I’m scratching my head rn.
@jesseojo
3 жыл бұрын
Can I plug my powerplay p16-I to aviom a320s?
@TS404ify
3 жыл бұрын
Thanx so much, friend! Please - show how to setup ultranet routing from wing to PA (NuQ, IQ, Berlin array, and other), with S32 stagebox.
@markweru9612
3 жыл бұрын
Thanks for the video. I wanted to ask though, how does the AES50 port have 48 outputs yet the stagebox has 16 outs only? How does that work?
@jshi600
3 жыл бұрын
Because you can add boxes to get more outputs. Or do a laugher box with more outputs. Also when using the DP48 you are sending 48 channels to this devices. Hopefully this helps👍🏾
@brother6027-h3g
4 жыл бұрын
I have 1-p16i and 6-p16m with 300 ft of cat5. The first p16m has great sound and powers up via cat 5 the next 5 don’t power up . I have to power them individually. The first 5 have signal but the last one no signal. One 300 ft long cat5 cable, 5 -10ft long jumper cat5 cables. What’s my problem? What do I need? POi cat 5 extender, or p16D?
@jshi600
4 жыл бұрын
Hello you would need to come out of a P16D from each port on the P16D to power your p16M
@victortavarez11
3 жыл бұрын
Hey so how can I set this up where I hear the eq and compressor settings, for example my drum mix in my p16 sounds raw no eq no nothing lol how can I send it? Thanks
@jshi600
3 жыл бұрын
You can send through buses or matrix’s.
@zhangxiang7383
3 жыл бұрын
Hi,can I use the “powerplay" to connect wing and P16?
@jshi600
3 жыл бұрын
No sir
@buzzfry1960
3 жыл бұрын
Are you sending from a kat 5 out of the wing . Or from the stage box. ?
@jshi600
2 жыл бұрын
I’m going through stage box 1st
@mehanunionchurch8474
Жыл бұрын
Thank you for the good info! The noise at the end of the video could have been quieter, relative to the speaking throughout.
@bback9119
4 жыл бұрын
Thank you, Jason. Can I ask you a question? Do you use the s16, Wing beetween P16m ?
@jshi600
4 жыл бұрын
kyu hun lee hello yes you have to that’s the only way to send the P16 signal. With a snake in between.
@bback9119
4 жыл бұрын
@@jshi600 Thanks. I see !
@emanuelmorales4529
4 жыл бұрын
Great video!👏🏻 how can I set it up I have the X32 as stage box which is connected to the distributor it would be the same way?
@jshi600
4 жыл бұрын
No it’s a little different for the X32. Let me know if you need a video on how to set it up thanks.
@emanuelmorales4529
4 жыл бұрын
Jason Robinson please do! It would be very helpful thank you very much God Bless.
@stephenevans2518
3 жыл бұрын
@@emanuelmorales4529 Late reply, but yeah you could set it up like that, you just have to route it in the X32
@emanuelmorales4529
3 жыл бұрын
Quick question how can I get in contact with you? I do have a few question for you.
@jshi600
2 жыл бұрын
Sorry just seeing your message you probably don’t need anything now but our number is 469-671-6886 email us at jason@sounddesignstudio.net
@alvaromunozdominguez5438
4 жыл бұрын
Hi from Spain!!! Thanks so much for this video! But, I have a question. Can you explain how is the setup connection if i have a stagebox Midas DL16? Do I connect to the Ultranet port? Thanks and I’m sorry for my English if I have mistakes...
@jshi600
4 жыл бұрын
Álvaro Muñoz Domínguez No you set them up to the AES 50 port, and you use the last 16 channels of the port like 33 through 48 will be your P 16 channels that you assign to p16
@alvaromunozdominguez5438
4 жыл бұрын
Sound Design Studio Thanks for your reply! But, you talk to me about the routing, no? So, can I connect the ultranet out of the stagebox to the p16?
@jshi600
4 жыл бұрын
Yes you come out of the Ultranet for the P 16s
@alvaromunozdominguez5438
4 жыл бұрын
Sound Design Studio thanks!!!! 👍🏻
@vokals
3 жыл бұрын
Hey great video! We did this last night at our church but they seem to be post fader. Is there a way we can send the signal to the p16 prefader? When we turn down our channel fader the signal stops sending to p16? Please help! Thanks again!!!
@jshi600
3 жыл бұрын
Daniel Ortega They should already be setup as prefader let me check again.
@vokals
3 жыл бұрын
Sound Design Studio thank you so much! We have rehearsal tonight! 😬😳😬
@vokals
3 жыл бұрын
@@jshi600 Any luck?
@cityofpraisetv
2 жыл бұрын
@@jshi600 how do I change my p16 channels to postfader
@dvirdahari4060
3 жыл бұрын
HELP! Hi I connected the P16 LED power on and the ultarnet LED is off, I did all the routing from the mixer according to the video
@jshi600
3 жыл бұрын
Could you please clarify your question or send a video to my email at Jason@SoundDesignStudio.Net
@BlessedBoyy_
3 жыл бұрын
Same here!
@im3thanrumfield
4 жыл бұрын
Man thanks for the video! But get some real line array behind you, none of that SBAL stuff lolz.
@@Seattlestratboy THANKS Marc for the reply but its no need to give this kind of comment any extra attention. I do the videos because I enjoy it. And I'm not the best at it yet , but most of these guys that make these comments will never have my resume so I don't worry at all. But thanks again Marc
Пікірлер: 56