This video saved my life. Trying to get my church setup and was having troubles finding the camera IP and connecting through the internet portal.
@terrenceshaw6927
4 ай бұрын
Thank you, my brother, I haven't even received my cameras yet but your set up tutorial has put me ahead of the game. Thank you.
@AJaytheCEO
4 ай бұрын
Glad to hear it
@GEORGEHOLMES-k9f
Ай бұрын
Thank you for your timely response. I will be asking more questions as they arise. You're a life saver.
@AJaytheCEO
Ай бұрын
Glad it was helpful!
@Ty1on3twelve
2 жыл бұрын
I'll update my three Fomakos. For those that don't know DHCP is Dynamic Host Configuration Protocol. I use two different programs to scan my network, Ping Manager and MyLanViewer. Good video.
@a3iuuu
9 ай бұрын
Anything for MacOS?
@kelvinsanaescott5500
2 жыл бұрын
Thank you my friend. I’ll try this out tonight
@thabonekomoshoeshoe
2 жыл бұрын
as a Tech leader on a new Church plant (in Lesotho, Sourthen Africa), i can testify that i learn a whole lot from watching your videos. i have implemented even some of the things you teach us. i have a question though, Which PTZ Cameras and a Joystick would you reccomend for a Church Plant on a low budget (mainly for Streaming)?
@AJaytheCEO
2 жыл бұрын
Thanks. I'd check out the Fomako or the AVKANS as Amazon runs good deals on these at low cost
@FrancoAversa
Жыл бұрын
Thank you, this video helped me for the first use of remote control.
@AJaytheCEO
Жыл бұрын
Glad it helped
@Dave4020
7 ай бұрын
Thanks AJ for the very informative video, and you are also pleasant to listen to
@AJaytheCEO
7 ай бұрын
My pleasure!
@johnhopkins7382
Ай бұрын
I would greatly appreciate it if you would cover using a ptz outdoors. I have a Fmk30Uh AI and have not been able to figure out how to set it up to prevent wash out. I use vMix HD. Thanks!
@WolfsHaven
Жыл бұрын
Because of my PTZ setup I use a gl-inet travel router and a switch that has PoE. That let's me hook up my 2ptz cams and controller my computer and ATEM all through one network with reserved IP's for the devices. I can then connect the router to the clients network or my cell.
@AJaytheCEO
Жыл бұрын
That's exactly how I do mobile events
@spiritandtruthministries7384
Жыл бұрын
I'm so thankful for you, Sir.
@AJaytheCEO
Жыл бұрын
Much appreciated
@MrIsraelParent
7 ай бұрын
Dude this is so helpful! We are about to finish our expansion and upgrading our camera system in on my lap and I’m learning as I go. Do you help people remotely? If so I’d much like your expertise. Let me know please
@AJaytheCEO
7 ай бұрын
Yes I do. Just go to my website to book a zoom meeting
@Ms84AW
4 ай бұрын
Grace to you! I just purchased the Fomako NDI PTZ. Do I have to buy an atem mini? We currently livestream with a 4K Canon
@AJaytheCEO
4 ай бұрын
You do not have to but how are you getting the video into the computer to stream?
@G.MILTONHOLMES-jz7qi
Ай бұрын
This video was very helpful. My question is what brand of HDMI cables do you recommend for long distances?
@AJaytheCEO
Ай бұрын
Dtech fiber optic HDMI cables amzn.to/3LAs9L9
@leeraysantiago
3 ай бұрын
Good evening, please I need to know which cameras would be good for my church, I would like to put 3 and be able to connect them to propresenter and be able to handle them from there. It would be possible. Please, I would like you to help me. Please, what equipment do I need to have to be able to connect everything.
@AJaytheCEO
3 ай бұрын
Email me and we can go over what options can work
@srowley85
2 жыл бұрын
I learned the hard way about setting a static IP address for the camera on the router. I originally set the static address on the camera only and started to have issues with losing control of it in the middle of services after the IP address suddenly changed. The weird thing was that the camera would disappear completely from the network and I couldn’t even find it using its MAC address. Once I set static IP for the camera via the router, these problems went away.
@hiram9337
2 жыл бұрын
what was the issue
@srowley85
2 жыл бұрын
@@hiram9337 I set the static IP address originally on the camera, which caused problems when the router assigned that same address to another device. I lost control of the camera several times during services as a result. Setting the static IP address on the router fixed the issue.
@KODIDesigns
Жыл бұрын
🎥🎞 Thanks you soo much. With what i know and what you shared, it's show time!!!!
@AJaytheCEO
Жыл бұрын
Glad it was helpful!
@IndianaSRN
Жыл бұрын
Very helpful -- VERY informative! Thanks for taking it solowly step-by-step! I'm sure my application will require a different setup since i stream live sports from a different school each week. I'm guessing I will have to bring a separate router.
@AJaytheCEO
Жыл бұрын
I bring a portable router when I stream games and everything is locked in so no need to change for different locations
@prisual
2 жыл бұрын
good video🤝
@AJaytheCEO
2 жыл бұрын
Thanks 💯
@SCWildlifeAdventures
7 ай бұрын
If you use these to live stream weddings for family members that can’t make it. When you set the IP address and then you take all the equipment to a location do you have to set it all back up again or just patch into their internet connection?
@AJaytheCEO
7 ай бұрын
If you set the ip addresses and connect everything to a switch they will all see each other without internet. you would only need to change something if the internet you are connecting to is using that same address for something else on the network
@williamjenkins9840
Жыл бұрын
Hey how can I set up appointment for visiting Church in Lansing IL.
@AJaytheCEO
Жыл бұрын
you can book something at ajayholmes.com/consultations
@Editor1206
6 ай бұрын
Hey Ajay. This video was created 2022. The church I go to just purchased the Fomako 2-23-24. In setting it up today, should I just choose DHCP for the 2 PTZ optics and controller for the IP address?
@AJaytheCEO
6 ай бұрын
Initially yes, then set it to static so they never change
@mrrljohnson
Жыл бұрын
Great video! Would it be safer to keep my system on a private network? To keep it from being hacked.
@AJaytheCEO
Жыл бұрын
That is fine but I wouldn't be concerned about these being hacked
@angelitoaisporna558
4 ай бұрын
Hi brother. Is there a specification for the switch? Like voltage and wattage?
@AJaytheCEO
4 ай бұрын
Make sure you have more wattage than is needed for everything connecting to your switch
@GordonGidluck
2 жыл бұрын
Great video!
@AJaytheCEO
2 жыл бұрын
Thanks!
@kashabbas110
Жыл бұрын
Hi Ajay - Does the Fomako Controller Support ONVIF? Could i connect a SMTAV PTZ Camera to the Fomako controller over ONVIF?
@AJaytheCEO
Жыл бұрын
Yes and yes
@kashabbas110
Жыл бұрын
@AJaytheCEO thank you, as always your a very helpful guy, top man. 👍
@tw2698
Жыл бұрын
@@AJaytheCEOhello AJay, how do you enable the onvif settings for FoMaKo ptz cameras? I cannot find it anywhere. I cannot find this answer anywhere
@soulsforchristdeliverancec5419
2 ай бұрын
Hey Boss so I have installed 5 new FoMako cameras I in a church. The church has 10 security cameras also. I am being told my 5 cameras have shut down 5 of there security cameras. Because they are on the same network. Can you help me solve that.
@AJaytheCEO
2 ай бұрын
That is not exactly true but I would make sure they do not have the same IP addresses as the security cameras
@soulsforchristdeliverancec5419
2 ай бұрын
@@AJaytheCEO So how do I solve this, because I am the one that installed these cameras and his setup was there before i came with know problem, i told it's my fault and it on me to fix it
@soulsforchristdeliverancec5419
2 ай бұрын
So his cameras have completely shut down and off line
@rinico75
Жыл бұрын
Would Love the static ip instructions for PC computer. Also you only plugged only network cables to camera but you had a picture, dont you also need HDMI cables ?
@AJaytheCEO
Жыл бұрын
Yes you need a video cable or you could get video over the network. I personally do not like doing this and always use an HDMI cable or SDI cable
@mccainsconcealcarry
Жыл бұрын
I am trying to set up my church's cameras for them to live stream. The only knowledge I have is from watching your videos. in the setup of the controller you put in the IP address, then you put in a subnet mask and gateway. Where do I find my church's subnet mask and gateway? Thanks for all your help, and the awesome videos you put out.
@AJaytheCEO
Жыл бұрын
Go to your computer go to command prompt then run ipconfig
@mccainsconcealcarry
Жыл бұрын
@@AJaytheCEO Thanks
@davidRodriguez-yt8cc
5 ай бұрын
I’m using the IP search tool and nothing is coming up when I search
@roberthehn1
3 ай бұрын
Can you mute all the beeps the joystick makes when pressing buttons??
@AJaytheCEO
3 ай бұрын
Yes that is under settings to turn off
@tw2698
Жыл бұрын
My brutha! Thx for all you do! I purchased 3 fomako (FM20SDI) PTZ cameras & a (zowieTek) ptz controller. I set all the cameras to a static IP address. The fomako ptz cameras doesn’t seem to have anything to enable the “ONVIF” Function. I believe that’s the missing link to completing this setup. Do you have any ideas?
@williamjenkins9840
Жыл бұрын
Hey did you connect computer to your Poe? On video I saw two cameras and your joy stick and router line and one more line you did not mention! And if I’m using a single camera do I need to change the ip address that was given when I connected the PTZ ? Thanks!
@alphonsoharkless1449
Жыл бұрын
I need advice for a Microphone and wire for my PTZ fomako camera and joystick and how to connect it
@AJaytheCEO
Жыл бұрын
Any of the IP joysticks I've used will work great and are you needing a mic to capture the rings sound connected directly to the ptz?
@alphonsoharkless1449
Жыл бұрын
@@AJaytheCEO yes do you have any suggestions it’s for our church we just have cameras and joystick nothing for sound
@Editor1206
5 ай бұрын
Good Afternoon Ajay. I am having a issue with getting my ip address to my Fomako KC608 Pr0 controller. Would be able to assist me with this?
@AJaytheCEO
5 ай бұрын
Email me questions@ajayholmes.com
@jorgevegarivera
Жыл бұрын
I purchase the Fomako SDI 20x because of your review but for what ever reason every time it zoom in/out the focus goes out for a while and kind of lag. Any suggestion?
@AJaytheCEO
Жыл бұрын
Please email a sample of the video showing it in action doing that
@jorgevegarivera
Жыл бұрын
@@AJaytheCEO thanks for your prompt respond. Where should I send the video?
@bartlomiejkaczynski8859
9 ай бұрын
Hi. i have bought two cameras and controller fromfomako few months ago on amazon. I will have one streaming on the weekend and on the location owner will use starlink, starlink have only WIFI connection, is there any option to connect your cameras to the controller without use the ethernet port/network? Can I connect your cameras to the controller if pov switch not will be connected directly to the network? Regards
@AJaytheCEO
9 ай бұрын
You would need to daisy chain them via rs232
@kaczuchasly5174
Жыл бұрын
I must do that on every single location when I will streming with my mac?
@AJaytheCEO
Жыл бұрын
You won't need to if you provide your own network
@kaczuchasly5174
Жыл бұрын
@AJaytheCEO I will use ptz cameras on the different location where will be evrytime different IP... what is the best ptz fullhd camera for the events like boxing nights inside rhe buildings etc? With easy setup? Regards.
@Husseinkanore
Жыл бұрын
Hi what software you use to setup ip address?
@AJaytheCEO
Жыл бұрын
To search in using advanced IP scanner. I'm setting them based on my local or the client's network
@PChislum
2 жыл бұрын
Should I be updating our cameras, I guess I gotta face my fears...dealing with iP addresses and network configurations
@AJaytheCEO
2 жыл бұрын
You don't need to as the firmware did what I manually did during your setup
@calvary-episcopal-church-b9774
Жыл бұрын
How do I set up the Fomako PTZ cameras and controller on POE?
@AJaytheCEO
Жыл бұрын
There isn't anything to setup. Once the controller and cameras detect power over Ethernet they will turn on of the on switch is on
@calvary-episcopal-church-b9774
Жыл бұрын
@@AJaytheCEO Great-I don’t have to worry about converting POE power to 12V DC? Your videos have been a real help, by the way. Joel
@rinico75
Жыл бұрын
Can you also set preset positions for the cameras?
@AJaytheCEO
Жыл бұрын
Yes you can
@LonzosStudios
Жыл бұрын
are they supposed to draw power from any switch? none of my devices power up
@AJaytheCEO
Жыл бұрын
Yes but only if it is a POE switch. Which switch are you using?
@ryannrjohnson
11 ай бұрын
Tried it using the Power Over Ethernet switcher but it still says no device found on the controller when I hit search.
@AJaytheCEO
11 ай бұрын
Have you tried adding it manually?
@ryannrjohnson
11 ай бұрын
@AJaytheCEO yes, for some reason it won't recognize it even when I add the ip address to the controller. I'll work on it again Monday. Camera responds to direct connection from controller, just not Power Over Ethernet from the POE switcher and controller, can't get them to recognize each other.
@ryannrjohnson
11 ай бұрын
@AJaytheCEO I connected the POE Switcher to the network today for the Fomako camera and it recognized the controller and is working now. Thanks. I'm on your PTZ Optics video right now cause the other church I play keyboard for has that and I've been stuck for 2 weeks trying to get it to connect to the controller. Yes, you're the man, none of these other videos on KZitem helped me connect the controller. Finally. Thanks again.
@williamoverstreet2210
2 жыл бұрын
Hello AJaytheCEO, What Camera do you like better Fomako PTZ or Avkans PTZ? Apples to Apples.
@AJaytheCEO
2 жыл бұрын
Fomako mainly due to the auto flip function
@williamoverstreet2210
2 жыл бұрын
If i have a warranty issue do they have a usa contact??
@livestreamequipment581
2 жыл бұрын
I personaly love AVKANS, their after services is very great, much better than some brand from USA. And I have to say, their camera are exactly same as some brand.
@williamoverstreet2210
2 жыл бұрын
@@livestreamequipment581 should i spend the extra for marshell? I just want to make sure i can get assistance if i need it. Also for warranty issues is it possible to talk to someone? Thank you for the info.
@livestreamequipment581
2 жыл бұрын
@@williamoverstreet2210 You can contact them via email. I got replied from Jenny, she is very nice, and very helpful. About the wrranty, I don't know much about it, you should contact Jenny.
@EarlSCarlton
Жыл бұрын
Is there a way to get the IP video in OBS? I looked in the instructions but it didn't work.
@AJaytheCEO
Жыл бұрын
Yes you would need to add video over IP. I don't recommend it unless you have tuned your network at the video will be slow and require syncing with audio
@michaelschneider4362
Жыл бұрын
Thank you very much for video. It helped a lot. I’m just curious. At 7:45 in your video, why did you set your computer to a static IP address in the 192.168.5.33 and the router to 192.168.5.1? Was it just to be in the same IP range as your camera temporarily? I’m a little confused why you did it. Because later, you changed everything to 192.168.0.whatever for your three devices. I’m guessing you changed your computer back to DHCP.
@AJaytheCEO
Жыл бұрын
Yes it was a temporary change to access the camera's factory ip address range
@divinesoundandlighit
Жыл бұрын
Will the controller work on other PTZ cameras. I have a 30x SDI/HDMI with POE that doesn't have a name. Will this controller work with this?
@AJaytheCEO
Жыл бұрын
I’m not sure but if it supports visca over up then yes it will
@techiebud
Жыл бұрын
Thank you for this informative video. It has been very helpful I am configuring 2 Fomako Cameras for my church, KN20A and KN30A. We also have the FoMako controller. I have set up the ip addresses for the cameras like your instructions show and can see them in my browser. I also set the controller to a static IP address which I can ping and see. When I press the search button,, I get the message "There's no VISCA device" on the controller. I am confused about how I can add these manually instead?
@techiebud
Жыл бұрын
I got it to work using the web interface for the controller..
@AJaytheCEO
Жыл бұрын
The fomakos defaults use onvif but I’m glad you got them working
@tw2698
Жыл бұрын
@@AJaytheCEOello ajay, this is actually the problem I’m having now. My 3 fomako’s need onvif to be enabled but there’s no way to enable it when you log into the browser. The only thing I see with settings in the browser is “Port Onvif”, with a setting of 2000. There’s not a way to enable it to turn on. Help🙏
@WestbankAdventist
2 жыл бұрын
can I set up a different brand PTZ camera on my Famako controller? If so how?
@AJaytheCEO
2 жыл бұрын
Yes you can. Any ptz will work as long as it supports a protocol that the controller supports. You would add them just like any other PTZ
@christianamuliproductions
8 ай бұрын
Can i get the link for the cable an the switcher
@AJaytheCEO
8 ай бұрын
Which cable and switcher are you referring to? There cables and joystick for the camera or my cables and switcher used to record and see the camera inputs?
@AJaytheCEO
8 ай бұрын
The poe switch is this one amzn.to/3RqAZir
@AJaytheCEO
8 ай бұрын
Also my Ethernet cables are custom made
@christianamuliproductions
8 ай бұрын
@@AJaytheCEOthank you that’s what i was asking for the ethernet switch
@Jkila25
Жыл бұрын
How do I find the ip address for the cameras??
@AJaytheCEO
Жыл бұрын
It is displayed in the upper left of the screen when the cameras turns on. Use any of the upgrade tools provided by the maker and it will show the address, on windows user advanced IP scanner, on Mac use lanscan
@dylanpersinger197
Жыл бұрын
Can the Fomako Camera be set up with another brand controller?
@AJaytheCEO
Жыл бұрын
Yes it can
@tcp3059
2 жыл бұрын
If you don't mind, I could use some advice for troubleshooting my fomako camera setup What I have is the fmk20UH (plug-and-play one) with a direct USB 2.0 cable to my laptop, and controlled by the model 601 joystick controller. When I first got it, I could control the camera with the ptz controller, but something got changed (not sure what) and now it won't control it. I want to try and factory reset the camera, but the only way to do so (that I know of) is to use the remote control to do so. Since there is no display on the camera, it is very difficult to navigate the menu, as you're basically flying blind. What should I do?
@AJaytheCEO
2 жыл бұрын
I'm not exactly sure as I have not used that one and I'd be guiding you blind as well. Email support at fomako and see if they can help you. Sorry
@tcp3059
2 жыл бұрын
@@AJaytheCEO No worries
@tcp3059
2 жыл бұрын
@@AJaytheCEO Update: Talked to Ivan at FoMaKo, and apparently you have to have your camera hooked up to a monitor to see the menu. This may also work if you plug it into your computer and pull up OBS or something similar, but I have yet to confirm it. Also, on your computer, it shows up as 'UVC Camera' on your devices page; as there's no drivers or anything, it doesn't give you a direct UI. Just a camera feed. But regardless, using the provided remote control and an actual monitor to factory reset the camera appears to have done the trick.
@josephsmith6653
Жыл бұрын
Can you do this without a internet connection?
@AJaytheCEO
Жыл бұрын
Yes. Set static IP addresses and it will work without internet access
@A2daj954
Жыл бұрын
Hey bro quick question can I run 3 Camaras and a joystick on a Poe switch that’s not connected to the internet?
@AJaytheCEO
Жыл бұрын
Yes you can. Just set the cameras and joystick to static IP addresses
@A2daj954
Жыл бұрын
Nice I know this is a rookie question but how do you change the Camara to static?
@kirvinbonner6893
2 жыл бұрын
Do you no how to set up the KC-601
@AJaytheCEO
2 жыл бұрын
By fomako?
@williamjenkins9840
Жыл бұрын
Are u located in the Chicago area? Our church is in Lansing Illinois. Would love for you to set up our 1 camera like those in this video!
@williamjenkins9840
Жыл бұрын
Are you in Chicago area?
@AJaytheCEO
Жыл бұрын
No I am not but I travel anywhere
@williamjenkins9840
Жыл бұрын
How can I contact you?
@williamjenkins9840
Жыл бұрын
Need contact info or call me 7086632200
@deyyahman
Жыл бұрын
what if you have a 10.0.0.1 network?
@AJaytheCEO
Жыл бұрын
They same steps work. Pick an available ip address, the subnet mask is normally still 255.255.255.0 and then the gateway and dns is typically 10.0.0.1
@NicholasHanges
Жыл бұрын
How do I add these cameras to Wirecast?
@AJaytheCEO
Жыл бұрын
Either you are them via network rtmp or you need a capture device
@NicholasHanges
Жыл бұрын
@@AJaytheCEO Would it be the same kind of setup for a PTZoptics camera? I used rtsp (not sure of difference between rtmp or rtsp ) Sunday but there was a lag (when using the joystick) and the KZitem quality was really low even though we have 300mbps up/down speeds. We were thinking we should return for PTZ instead. Thank you!
Пікірлер: 145