Dear Tony, i have watched and re watched this series. Im a DIY once in a while and in Qatar so its hot here. I hv the Iwata same model. About to attempt failing clearcoat repair with a pearlesant basecoat. Really appreciate the guides, russell
@satan15151515
4 жыл бұрын
IWATA Air Gunsa AZ3 is probably the best beginner to intermediate gun out there.
@TonysRefinishingTV
4 жыл бұрын
Sure is mate
@watchthisspacecarchannel6523
4 жыл бұрын
Great tutorial, apart from learning how to spray a panel, another highlight I think most beginners should take away from this , is that you don’t need to start with all the high priced top of the range guns. This is a good brand , affordable spray gun that is versatile for a beginner to start with and know that it will last if you look after it , great video Tony !
@TonysRefinishingTV
4 жыл бұрын
That was my whole point in using a gun like this for these videos mate ain’t fair on beginners if I use a £500-600 gun to show this with so I thought sod it asked our sponsors they sent me out the one I asked for so I could show a good low priced gun suitable for beginners and as always they came through and then even put a deal up on it for you guys can’t say better than that
@stephenlebillon3066
3 жыл бұрын
Thanks for passing on all your knowledge,as a beginner I’m at the primer stage of my gpz 600r repaint, would never have started without your help,many thanks again from NZ.
@greasemonkey6919
4 жыл бұрын
So glad that I found your channel. I am attempting to repaint my car during this quarantine period and your videos are very detailed and informative. Keep up the good work and keep those videos coming. All the way from the Caribbean Islands, Trinidad...
@johangranberg1058
3 жыл бұрын
The best mowie for beginners i have found on youtube
@TonysRefinishingTV
3 жыл бұрын
Thanks Johan 👌
@husky1232
4 жыл бұрын
Hello Tony i just purchase this gun of PMP will be trying it out soon as my small spray booth will be ready great video can't wait till the episode
@TonysRefinishingTV
4 жыл бұрын
Thanks man and it’s a great little buy that gun mate as you can see it works well for a lower priced gun and it’ll last if it’s looked after too
@digchilli
8 ай бұрын
This video really helped me setup my gun and paint 2K clear on my first attempt at painting a van. Your vid was perfect, I definitely would have made some big mistakes without it. I did see a drip and tried to wipe it off, oops, that didn't turn out well 😆 But overall I am really happy with the result. The best time to remove masking tape from a hard edge would be great info too - the van I am painting has an unpainted rubber seal between panels. I removed the tape about 30 minutes after painting, I am a little concerned that the paint may flake over time...time will tell.
@evans007bmw
4 жыл бұрын
What a great tutorial, clearly spoken with all the details you need. Baffles me why someone would put a thumbs down for this, jealousy i guess. Keep up the great work tony, i have completed a few repairs on my car based on yours and the gunman's tutorials.
@TonysRefinishingTV
4 жыл бұрын
Hey buddy appreciate the comment mate I always try my best to get as much detail and content for you guys into videos as possible and nice to have you with us too fella
@jerrychircop7121
3 жыл бұрын
Have you ever considered teaching at a local high school or college? I think you would be one of those cool teachers that the students will be drawn to and I see you as a good influence for the kids. Go out and make a difference in this world mate!!
@TonysRefinishingTV
3 жыл бұрын
One of my main jobs in a previous employment was training apprentices mate and funnily enough I was asked to become a teacher in this trade last year but I love to do the job too much as much as I love to inspire and help others learn
@ferozshaikh762
4 жыл бұрын
Very good 👍 spray gun setting and paint finishing i am spray painter and job 20 years
@nickpaxinos141
4 жыл бұрын
Probably the best explained video I've seen on the subject , thank you
@TonysRefinishingTV
4 жыл бұрын
thanks nick awesome to have you with us
@deandempsey264
3 жыл бұрын
Your measurements are bang on perfect exactly how I go at it 👌👌
@TonysRefinishingTV
3 жыл бұрын
Thanks buddy
@steveguest8028
4 жыл бұрын
Superb as always Tony,I’ve just purchased one of these guns from PMP supplies including the free regulator and sealey spray gun on your recommendation...looking forward to more of the same bud 👍
@TonysRefinishingTV
4 жыл бұрын
plenty more to come on this series mate dont worry, and plenty more using one of these guns too great purchase this gun for beginners
@jasabasenara8124
4 жыл бұрын
What a brilliant video. The best I'd say, for explanation simplicity. Many thanks.
@davutyalcin-
4 жыл бұрын
Hey buddy good to see you again with a fresh new upload. I keep following you. Best regards,Davut from the Netherlands
@TonysRefinishingTV
4 жыл бұрын
hi davut always nice to see you here and have you with us
@davutyalcin-
4 жыл бұрын
Tony's Refinishing thank you tony 😊
@hoodgrimreaper
Жыл бұрын
❤ amazing work ! Amazing video brother!
@mansellsautos
2 жыл бұрын
Hi Tony these videos a really great and have helped me gain more experience they really have.. I have purchased the spray gun 🔫 and it's really is a great purchase..and will carry on watching the highly recommend videos. I think one of the areas I could improve is the clear coat. Could you possibly recommend a good product basically for small jobs ie the odd wing and door and bumper repairs and where to get it from. Thanks in advance Chris.
@carbonbodyworker
3 жыл бұрын
Great tips tony! Really enjoyed this.Gave me some confidence cheers mate 👍
@TonysRefinishingTV
3 жыл бұрын
Your welcome buddy and glad they help too
@Mikefngarage
4 жыл бұрын
nicely done tony well explained. I need to make another video my first ones where I explained this were pretty lame. So I am going to make one with using Tamco USA made material. I haven't used roberlo clear but I have used their filler which is pretty nice. It poured pretty high solids to me. finish looks acceptable. I usually spray a bit closer and smash the dots just a smidge gets a wetter finish but that would be fine for the panel you are putting on.
@TonysRefinishingTV
4 жыл бұрын
well bear in mind this was aimed at the beginner mate i wouldnt try to teach people to go as wet close ect as i would to start
@dalegibb95
4 жыл бұрын
Loving these videos, really good for someone like me trying to get into painting
@TonysRefinishingTV
4 жыл бұрын
Thanks dale really glad they do help people mate like yourself that’s what the channels all about
@VeekAtanees8830
4 жыл бұрын
Excellent job. Good info. Clear to follow. Keep up the good work.
@TonysRefinishingTV
4 жыл бұрын
Thanks Johnathan
@v8man350
4 жыл бұрын
Excellent tutorial mate, well explained , keep up the good work 👍🏻
@TonysRefinishingTV
4 жыл бұрын
Thanks fella and we will mate
@srodgie
4 жыл бұрын
One brilliant video Tony.... very well explained! Keep up the great work! 👍👍👍
@TonysRefinishingTV
4 жыл бұрын
Thanks Steve great to see you here again too mate
@srodgie
4 жыл бұрын
@@TonysRefinishingTV 😉👍👍👍
@jayakumarp.m.2596
2 жыл бұрын
Very smooth coat, how much is the CFM of your spray gun and how much is the CFM of your SPRAY GUN?
@HAMEED...
4 жыл бұрын
Awesome video . Really helpful . Waiting for your upcoming videos .
@TonysRefinishingTV
4 жыл бұрын
Glad it’s helped mate thankyou
@Eckascliovalver
4 жыл бұрын
Another brilliant tutorial mate. Well done 👍🏻
@TonysRefinishingTV
4 жыл бұрын
Thanks man appreciate that buddy
@hillbillycustom1730
4 жыл бұрын
Toney man you are doing a great job brother
@TonysRefinishingTV
4 жыл бұрын
Thanks buddy trying my best to get these as clear and simple as possible tbh for everyone and break it right down
@adidasandy1
4 жыл бұрын
Another great educational video. Well done
@TonysRefinishingTV
4 жыл бұрын
thanks andy
@tonyhaz6664
4 жыл бұрын
Cracking vid m8, would I do the same method, when using direct gloss ?
@TonysRefinishingTV
4 жыл бұрын
Pretty much mate yes I’m do one on direct gloss for you guys too on direct gloss I’d probably go one light coat two wet coats though as the polishing stage actually takes colour off the panel so to be safe I would put one extra coat on to reduce the risk of rub throughs
@jaysmith1203
Жыл бұрын
Great video Tony, is there a particular temperature the clear coat and panel should be when spraying? I'm assuming if it's too cold, the clear coat will run?
@TonysRefinishingTV
Жыл бұрын
so average is 20c but obv thats not always achievable for some but you can spray alot lower just be more careful and extend the flash of times ect
@lummy321
4 жыл бұрын
Awesomeness Tony ... Great tutorials as always . Peace man
@TonysRefinishingTV
4 жыл бұрын
Thanks fella
@gall49611
4 жыл бұрын
Another well explained and simple video.....I can’t wait to get spraying now! Being a DIY guy I’m not sure how I’ll fair with my garage barley getting above 10c 😬
@TonysRefinishingTV
4 жыл бұрын
Lol we all started somewhere mate and it can be done beleive me lol just slow everything down abit more and take your time , we will also be running some introduction to paint days at my shop this year covering stuff we’ve done in the vids like this one but hands on
@bosivain
4 жыл бұрын
Warming your paint in hot water helps to
@TonysRefinishingTV
4 жыл бұрын
it does but its something ive never done myself
@andybussa1323
4 жыл бұрын
You should invest in a heat lamp,also you can add rocket into you clearcoat to speed up the drying process but be careful not to add to much
@gall49611
4 жыл бұрын
Andy, I’m getting there now mate....still a complete noob but I’m getting there. Pretty pleased with my results so far and absolutely loving the process 😁
@medievilassassin
3 жыл бұрын
Great videos mate , have you and recommendations on a respirator when using 2K paints please
@AquzdHD
4 жыл бұрын
Very good tutorial well explained
@TonysRefinishingTV
4 жыл бұрын
Thanks Hayden
@babame2629
4 жыл бұрын
Nice job thanks please let me know after how many hours is that to polish, thanks
@kamildarek3425
4 жыл бұрын
Simple but brilliant
@TonysRefinishingTV
4 жыл бұрын
thanks kamil
@michaelbekendam5449
2 жыл бұрын
love your work
@TonysRefinishingTV
2 жыл бұрын
Thank you! Cheers!
@EssexSilvering
4 жыл бұрын
Brilliant ... Thanks for sharing.
@darrenbirchall7826
4 жыл бұрын
Another great tutorial, cheers
@TonysRefinishingTV
4 жыл бұрын
No problem Darren thanks for watching fella
@ukaszzielinski8166
3 жыл бұрын
Regardless of the gun it can be considered that the gun should be open in a dose of material at least 70% to spill clear coat? I have Lvlp gun and I would like to be sure how my gun should be set up
@MrBombeiro11
4 жыл бұрын
Great job my friend 👍👍👍🇵🇹🇵🇹🇵🇹🇵🇹
@TonysRefinishingTV
4 жыл бұрын
Thanks buddy
@giorgosnak9927
4 жыл бұрын
Very nice videos man!!I am a DIY guy and i want to buy a compressor to work with the guns....what specs (cfm, hp, tank) are ideal for small jobs like panels, doors, bonnets etc?Also is the Air Gunsa AZ3 HTE2 proper for a job like this on the video bucause is supossed to be primer gun, but has a 1.3 tip?If you have a gun to propose me around 100-150 euros you are most welcome!Keep up the good work!
@RGD-Audio-Repairs
4 жыл бұрын
i NEED that panel :D I have a mk2 focus in moondust silver :D and my mrs dented this wing :D
@TonysRefinishingTV
4 жыл бұрын
This is off a fiesta mate not a focus and women hey lol
@RGD-Audio-Repairs
4 жыл бұрын
@@TonysRefinishingTV Ahh identical wing to a mk2 focus :D
@virgilarce
4 жыл бұрын
Good job Tony Thank you !
@TonysRefinishingTV
4 жыл бұрын
thanks buddy
@ZUKE12345671
3 жыл бұрын
Hiya mate, going to be painting my Riley in the next day or two. 2k solid and I want it to have that "old car" with "plenty paint on" look...not like a modern car. how many coats do you reckon mate ? Think I sent you a picture of it a bit back...its a Riley RMA. as a rough guess, with say, three full coats roughly how many ltrs of paint ....Cheer mate !!
@TonysRefinishingTV
3 жыл бұрын
Replied on Facebook mate
@PnwOnTour
4 жыл бұрын
And had clear left over to boot 🥾 wow might have to wind in my fluid!
@TonysRefinishingTV
4 жыл бұрын
Yeah mixed a little to much for that one lol
@PnwOnTour
4 жыл бұрын
Seemed efficient but you’d know better than me haha 👏🏻
@TonysRefinishingTV
4 жыл бұрын
It’s a very efficient gun tbh mate for something on the cheaper end of the scale
@johnniepassmore5341
3 жыл бұрын
Hi luv watching your channel. How long would that take to fully cure reasy to cut n polish under a heat light.. thank u
@TonysRefinishingTV
3 жыл бұрын
Just replied to you on insta fella
@4dtruth192
2 жыл бұрын
Sir is it OK to leave the remaining clear coat paint in the spray gun until the following day?
@TonysRefinishingTV
2 жыл бұрын
No most only have a pot life of an hour
@lummy321
4 жыл бұрын
Awesomeness tony ... Would an IR lamp bake paint efficiently?
@TonysRefinishingTV
4 жыл бұрын
Yes mate you can dry base or clear with an ir lamp mate
@lummy321
4 жыл бұрын
@@TonysRefinishingTV brilliant tony 😎 ... Waterbase additive is used to thin the waterbase paint ? Think i remember you saying a while ago buddy
@TonysRefinishingTV
4 жыл бұрын
Bruce Lumsden yes mate il also be doing a video on our scheme and system too mate which will show it all in one detail
@ivanivanov-rc2kv
2 жыл бұрын
What this gun with nozzle 1.8mm for primer painting? Thanks
@johnniepassmore5341
4 жыл бұрын
How would u dry the 2k clear in shed at home... Luving the channel lots of knolage
@TonysRefinishingTV
4 жыл бұрын
Johnnie Passmore hiya mate I’d leave it to cure through on its own for 12-24 hours depending on the temp
@johnniepassmore5341
4 жыл бұрын
@@TonysRefinishingTV will it be ready to flat n polish after 24 hrs.... and is that time for most clears or every clear?
@TonysRefinishingTV
4 жыл бұрын
If it was say middle of the summer or the warmer months ( if your in the uk ) then you could paint one day polish the next if you were leaving it to air dry with most clears mate weather like we have atm I’d be leaving it 24 hours to air dry in a cold garage
@tyronemcfarlane2101
3 жыл бұрын
Hi mate. Great videos, very helpful. I'm looking at spraying alloys and would be getting two devilbliss GPI's one for base and one for clear coat. What mm nozzles would you recommend for each?
@TonysRefinishingTV
3 жыл бұрын
Why the gpi mate ? And I’d go for 1.3
@TonysRefinishingTV
3 жыл бұрын
There great guns mate 1.4 is abit heavy tbh take a look at spsupplies.co.uk our sponsors
@tyronemcfarlane2101
3 жыл бұрын
@@TonysRefinishingTV yeah I noticed soon after that message that they don't come with nozzles smaller than 1.4. I'll check out that website. Nice one
@jarfar95
3 жыл бұрын
For home DIY-er's what options do we have for 2K with no isocyanates?
@TonysRefinishingTV
3 жыл бұрын
Honestly mate that’s something I’ve never looked at tbh most products these days are low voc but I’m not sure
@mechanoid5739
3 жыл бұрын
Would you recommend a Divilbiss FLG5 gun for a beginner?
@TonysRefinishingTV
3 жыл бұрын
Personally on top sizes and ease of use I’d recommend this over the flg
@dumindajayasekara3785
3 жыл бұрын
I want to spry clear coat like a mirror... Pls advise how to do that
@TonysRefinishingTV
3 жыл бұрын
Spray the clear down as flat as you can and polish it to a mirror clear can’t be sprayed to a mirror finish
@full_metal2452
4 жыл бұрын
Also--Wear nitrile gloves not only to protect yourself from deadly isocyanates/VOC's but also so you don't contaminate the oils/salts from your hands onto the tack rag and then onto the panel.
@TonysRefinishingTV
4 жыл бұрын
yeah was my bad that id ran out of gloves the morning i did this video lol
@alzzla2730
4 жыл бұрын
Top job👍
@TonysRefinishingTV
4 жыл бұрын
thanks
@Jaimerga
4 жыл бұрын
Hi Tony, Excuse me, what is the difference between AZ3 and AZ4? Which do you recommend more? Regards!
@TonysRefinishingTV
4 жыл бұрын
Az3 is the full size gun az4 is a mini / midi gun mate
@Jaimerga
4 жыл бұрын
@@TonysRefinishingTV Thanks you!!
@TonysRefinishingTV
4 жыл бұрын
Jaimerga no problem fella
@gotzz84
3 жыл бұрын
I have AZ3 HTE-2 so what's the difference with HTE-S ?
@TonysRefinishingTV
3 жыл бұрын
Just a newer version I think mate
@akira5982
4 жыл бұрын
I'd be happy just too have a 1 colored car 😅
@TonysRefinishingTV
4 жыл бұрын
lol
@baileyeverard7271
4 жыл бұрын
Hey so you went over the panels 2 times which each coat, why is that? Thanks
@baileyeverard7271
4 жыл бұрын
Or did you just replay the clip? Didn’t catch that lol
@JohnWD40TC02
4 жыл бұрын
Hi Tony, hope you are ok and your wife in improving, haven't called for a couple of days as you have better things to do than chat to me but if you have the time I have a question for you mate, I lay down my first coat of clear and it looks great with a flat glassy finish but after the second coat it has quite a lot of peel in it, I use the same gun same settings (full fan, 3 turns out on fluid and 34psi) and distance but I just move a little slower, any idea as to why this is happening? I know this is user error but not sure how to fix it, flash off is 10mins, any help would be appreciated mate, John
@TonysRefinishingTV
4 жыл бұрын
JohnWD40TC02 which gun are you using mate ?
@JohnWD40TC02
4 жыл бұрын
@@TonysRefinishingTV I'm using my devilbiss sri pro lite 1.2 mini gun, I have two of these one for base and one for clear which of course is the roberlo 610, I know the gun pressure sounds a bit high but been using that after watching the gunman clearing a bumper at the same pressure.
@TonysRefinishingTV
4 жыл бұрын
Not sure tbh mate not really used one , best thing with 610 is a fine wet coat then a real wet coat
@JohnWD40TC02
4 жыл бұрын
Ok no problem Tony, I'll try that and see how it goes, I do have some more unrelated questions but I think it's best if I ask you on FB, don't like bothering you atm as you have enough on your plate so I'll give you a few days then give you a call.
@Irfan-or9sd
4 жыл бұрын
Which clear coat would you recommend?
@TonysRefinishingTV
4 жыл бұрын
roberlo premium hs 250 or roberlo kronox 610 uhs
@victormoreno1124
4 жыл бұрын
Hola buenas algún concejillo para evitar piel de naranja
@TonysRefinishingTV
4 жыл бұрын
gracias
@bobanppvc
4 жыл бұрын
Hi Tony.What are dimensions of that booth.It has just exhaust fan right?
@TonysRefinishingTV
4 жыл бұрын
no mate its a proper booth so its 7.5 meters long 4m wide 3m tall the whole roof in this is the input filters and it has a fan unit and heating unit pushing air in through the roof filters and then extracts through the rear
@bobanppvc
4 жыл бұрын
@@TonysRefinishingTV so it has intake blower?
@TonysRefinishingTV
4 жыл бұрын
Montenegro ZETA yes this is a full proper booth not a home built one it’s a full dalby booth bake the lot mate
@bobanppvc
4 жыл бұрын
@@TonysRefinishingTV people use negative pressure booths a lot.I saw gunmans video his booth use just exhaust fan so its not big thing if it has just one fan that extract air from booth instead of two
@TonysRefinishingTV
4 жыл бұрын
yes but this setup has plant to put air in and plant to take air out
@ddcarshinedeepakdubey5879
2 жыл бұрын
What Nozzle size does this have sir
@TonysRefinishingTV
2 жыл бұрын
1.3 mate
@cristianb.4135
3 жыл бұрын
Hy Tony, can i ask you why my clearcoat (on a solvent base)lose its gloss after 1 or 2 ours but, if i spray It on an old wel cured panel this problem doesn't happens? I used the ICR SPRINT H62 with fast hardner. The ambient temperature around 10-13 degrees here in Sardinia..
@TonysRefinishingTV
3 жыл бұрын
The faster the hardener the more it will pull back , also if your base isn’t fully dry ( may be dry to the touch but could still be slightly not quite off ) then it’ll pull back or it could be your clear or thinners there’s a Humber of things that could make it do it
@cristianb.4135
3 жыл бұрын
@@TonysRefinishingTV thanks for the reply, so can i spray the clear over the base letting it dry for a night?
@TonysRefinishingTV
3 жыл бұрын
It depends on your manufacturer tbh I’d leave it an hour if your air drying and it’s cold / damp then try and hit it with clear
@masoodamg6633
2 жыл бұрын
👍👏
@JohnWD40TC02
4 жыл бұрын
Hi Tony new subscriber here, still learning to paint and having problems with my clearcoat, using upol 20:80 and fast hardener but I'm getting bad peel. I have the devilbiss SRI Pro lite 1.2 with the TE5 cap and 2bar, I'm only spraying small parts that I fabricate myself but do need a good finish. I don't have a heated booth so it's around 10C in my booth, I've been heating my mixed clear in boiling water plus heating the parts with my IR before spraying to around 35C, do you think I'm over doing the heating stage causing my peel issue, should I just heat the part and not the clear. I also find that the clear takes 4 or 5 days to harden, is this normal or is upol not a good make of clear, sorry for all the questions but I'm pulling my hair out trying to get a good finish, Oh an using Jet Black solvent basecoat. Thanks, John
@TonysRefinishingTV
4 жыл бұрын
do you add a drop of thinners into your clear mate , ive never used that clea or gun tbh but warming everything up like that is something ive never done and in this video we were spraying at 10c no issues and it shouldnt really take that long to dry either, im thinking warming it all up so much may be making it dry to fast so its go no time to flow out on the surface before it flashes off
@JohnWD40TC02
4 жыл бұрын
Thanks for the reply Tony, I didn't add any thinners as the data sheet states its optional and its quite thin as is, I'll try again without the heat, as I'm using an extra fast hardener (5 to 15C) you are probably correct that its flashing off before its flowed out.
@TonysRefinishingTV
4 жыл бұрын
JohnWD40TC02 always try to rely to everyone fella if I can the help always expands further than the videos , and if you get stuck after adding a tad of thinner 10% I’d try personally I use that in most clear , then drop me a message on our Facebook page as it would be easier to chat in the future if you need some more focused advice
@JohnWD40TC02
4 жыл бұрын
Hi Tony, just to let you know that I added 10% thinners, didn't heat the clear and only heated the panel to 17C (ambient was 7C), sprayed 2 coats one medium and one wet and the finish was like glass, quick flash off very little peel. Really appreciate the help here Tony, your advice was spot on. 👍👍
@TonysRefinishingTV
4 жыл бұрын
honestly mate brilliant fella so glad to see you've got it nailed now mate and was my pleasure buddy always help out where and if i can mate, keep smashing it now fella
@jamiebeddingham5838
3 жыл бұрын
Hi wonder if you can help I am getting quite a lot of dust in my clear coat but not in base coat. I am using an extractor fan and getting spray tent quite hot 23oc humidity below 50%. I need my clear coat to dry faster I am using mipa cx4 2k hs clear coat any advice thanks in advance again
@TonysRefinishingTV
3 жыл бұрын
Hi Jamie what sort of environment are you spraying in
@jamiebeddingham5838
3 жыл бұрын
@@TonysRefinishingTV thanks not ideal but got a tent 3x3 and 3m high, sealed edges ground sheet on the floor covering up any gaps two fan heaters and an extractor fan to suck out dust. I am not putting any thinners in the Clearcoat as I was not at the shop I didn’t need to.
@TonysRefinishingTV
3 жыл бұрын
@@jamiebeddingham5838 cx4 doesnt really need it tbh its thin enough , as for dust just make sure your guns spotless ect tack before clear unfortunately unless your in a decent half sealed room with extraction its hard to cut down on nibs mate
@jamiebeddingham5838
3 жыл бұрын
@@TonysRefinishingTV thanks for advice I am trying again over next couple of days I never thought after watching your video the other day of blowing off with airline whilst tac rag I’ll try that your videos are great. Thanks again
@TonysRefinishingTV
3 жыл бұрын
No problem at all Jamie hope you manage to get it to improve abit , also filter everything mate dusts our enemy lol 😂
@miller68
4 жыл бұрын
👍
@TonysRefinishingTV
4 жыл бұрын
👍
@dbdb4274
4 жыл бұрын
What can is that
@TonysRefinishingTV
4 жыл бұрын
Can?
@WilterLagan
3 ай бұрын
Me: I'm using 100 Malaysia ringgit spraying gun 😂
@valentinomakstry
4 жыл бұрын
Wrong! First coat do not need to spray the edges always the second coat, otherwise overbuilding the edges....
@TonysRefinishingTV
4 жыл бұрын
Personal opinion I’d say on that I’d rather have two coats of clear over a whole panel than one coat on edges and two all over so the whole panel has the same protection
Пікірлер: 168