Talked to you and fixed my 2017 XP 1000 with 32s at the end of last summer. Right after I added the washer and your belt, I snapped my reverse chain. After getting the transmission back in I've done 200 miles with tons of 60+ all the way up to top speed for extended time with no issues. Totally stopped my RZR from ripping off bottom teeth and no other belt issues either.
@bigred6220
4 жыл бұрын
Dude! My RZR ripped off bottom belt teeth too! What causes that?
@oby-1607
4 жыл бұрын
I have that same impact gun and it has served for years with no problems. Milwaukee power.
@MinnesotaEric
4 жыл бұрын
Over 2000 miles with a Gates belt and then one afternoon of near wide-open going ten miles down a road chasing rally cars to the next check point and my belt blew teeth. Now I know why. Two blue washers on order. Thank you.
@Hunterworks
4 жыл бұрын
MinnesotaEric could have just got our white. But it may not be enough for the gates to run wide open.
@MinnesotaEric
4 жыл бұрын
@@Hunterworks Wait. Stop. You didn't say anything about a thinker washer than the stock blue. LOL Are you suggesting an 1/8" shim is best? If I need to, I'll cut another washer out of plastic sheet stock.
@Hunterworks
4 жыл бұрын
MinnesotaEric this video is older than our washer is. We have videos on it too. Also have a updated version of this video
@MinnesotaEric
4 жыл бұрын
@@Hunterworks Add a card right at the beginning of your video that points to your new white washer video, or delete this old video since you seemingly have not monetized these videos. Anyway, I ordered your new white washer, and for twice as much money, I ordered two old blue washers. Sigh. LOL
@Hunterworks
4 жыл бұрын
They are monetized and if you had two blue you didn't need to buy our white. But with the gates you might need three blue or our white and one blue to stop it from blowing at high speeds or just buy our belt
@pjgsxr66
5 жыл бұрын
Great set of new videos Todd! I could never figure out why i kept ripping teeth of those Gates belts. I've learned so much about my Xp from your site and channel..
@Hunterworks
5 жыл бұрын
Appreciate that!!
@mechanicforlife9468
5 жыл бұрын
You missed your calling in life and should have been a teacher. LOL. Great video and I appreciate you taking the time to show what you have learned. I didn't know what the blue washer was for and had removed mine. Going to put it back in. Cheers
@provousa2253
Жыл бұрын
I own an 2020 Arctic Cat XX and because of these videos I somehow managed to get 5,000+ miles and never blown a single belt I replace them(@1,500) out of fear but still have them all?? Today 10/10/22 I finally got/needed a brand new clutch and hope to get another 5,000+ miles wishing he had belts for my machine but anyways his "Knowledge" is the Secret to extended belt life no doubt!!!!
@Hunterworks
Жыл бұрын
Thanks for your comments
@moehoward69
4 жыл бұрын
"Just know when to quit. " works in so many aspects of life ! 😁
@Hunterworks
4 жыл бұрын
What does this mean?
@moehoward69
4 жыл бұрын
@@Hunterworks know when to quit the cordless impact wrench, know when to quit the drinking, know when to quit smoking, etc. Yaknowhatimsayin?
@clintbuccola3897
5 жыл бұрын
fantastic info, I'm learning a lot about rzr, I'm going to try your belts, thanks
@workhard3994
5 жыл бұрын
Clint Buccola I feel like like people repairing there Polaris so much there learning about them I don't know of that's a good thing or a bad thing
@brianfry7441
5 жыл бұрын
Great information Todd, thanks
@oldpro7401
5 жыл бұрын
Can't believe you are using that impact ;) :) LOL....sorry...I had to. Really good video!
@rcclassiccrawlers4368
Жыл бұрын
Great tips! Thanks for sharing.
@whopper809
5 жыл бұрын
Sorry to say but Gates Belts have been garbage for years.. Thanks for the clutch adjustment tips.. Blue washer going in!!
@jeremyroy6621
5 жыл бұрын
I’m gonna order the blue washer and a belt for a spare. I got a 2018 xp, you stated that Polaris doesn’t even have the 1 washer. So should I order 2 washers to be on the safe side? Thanks so much for the helpful videos.
@wildmanturner
Жыл бұрын
I use a silver washer and it works even better. Going to try a magenta washer soon
@UTVGuide101
5 жыл бұрын
Well done Todd
@carlignash4590
4 жыл бұрын
I appreciate the videos. Good information.
@lance8167
3 жыл бұрын
Wow great content I got a 500cc scooter with the CVT transmission and we put a washer on our variator is called the fuzzy washer basically that's the same thing you but mine's not blue I like the blue washer
@jevonthomas2373
5 жыл бұрын
Thanks for getting back is there anything I need to do to it it's for my daughter and she easy on the machine and this is our first time owning a side by side.
@XMARGH
5 жыл бұрын
Liked & Shared On My Facebook Page. Always Appreciate You Sharing Your Knowledge Todd! Thanks!
@Hunterworks
5 жыл бұрын
Thanks
@richardvilla3161
3 жыл бұрын
I use a torque stick of 100 ft lbs on my impact and it just makes me feel better maybe wrong way to do it but like you said it’s hard to hold the primary clutch
@Hunterworks
3 жыл бұрын
That’s a good idea
@Mitch_Bierma
5 жыл бұрын
2016 xp 4 1000 getting misfired codes and they said i burnt a belt. 2016 highlifter i was with did same thing but blew belt into pieces. confirming a second blue washer on the primary with help not burn up new belts on? also great video (ironically i cant wait to get to try one of your belts, hopefully its not a blow out though)
@charlescasey9799
3 жыл бұрын
Great job
@grasscutter88
3 жыл бұрын
Interesting design for a cogged belt. You would think that would be more of a v belt design.
@djWOOF
Ай бұрын
Hi todd, im not seeing a washer available on your website for the 2024 XP1000 - is it not available? or look under another model
@Hunterworks
Ай бұрын
not needed, totally different clutches
@djWOOF
Ай бұрын
@@Hunterworks thank you!
@alliedominguez2805
4 жыл бұрын
So will the blue washers fit a 2016 xp 41000 or the white ones? one more thing i bought a set of 32" Tensor Regulator tires and wanting to put them on,on my factory wheels which r 29x9x14" fronts < Rear r 29x11x14" and i havent installed aftermarket clutches it still running on stock clutches my question is will i run into problems if i use them big tires on stock clutches? And i dont do crazy stuff on my rzr or race;sometimes i jump but not rarely just regularly driving on sand and mud no rock climbing yet,and im gonna replace my square pucks to round ones what do u recommend ? thanks, love your videos Mr.Todd
@Hunterworks
4 жыл бұрын
black panther3045 hernandez Thank you for your comments and shoot me this in the mail Todd@Hunterworks.com
@kenstegmann1057
5 жыл бұрын
Purchased 2016 900s new only 226 miles very few hrs and is stock no riding till spring I will then change all fluids,oils etc.should I add the extra washer?I do need a spare belt will purchase yours what one would you recommend will keep Oem for spare also should I change to round rollers or the pucks I’ve heard about. I can wrench just haven’t tore a clutch apart new to the RZR nuby thank for any info
@Hunterworks
5 жыл бұрын
You should do the rollers but you probably ok without the washer, have not heard of 900 doing this.
@randy-yo8zi
9 ай бұрын
Learning a lot from your videos i have a 2015 rzr4 eps. How often you replace the blue washer, and do I install 2? Finally experienced first blowing belt. Close to 3000 miles, had a spare always, blue washer makes a lot of sense. Any info would be appreciated 🇺🇸🇺🇸
@Hunterworks
9 ай бұрын
Assuming a XP 1000 you have have, we do not use the blue, we make our own washer and it is just one. However with 3000 miles, you might have more going on, you are in the average lifespan of the primary . The washers really do not wear out, they get mashed from spider nut and spider backing off though
@randy-yo8zi
9 ай бұрын
@@Hunterworks I'm not sure if there's even a washer in it i've never Took it a part, Would you know if players makes that part for the razor 4 900 Eps
@Hunterworks
9 ай бұрын
@@randy-yo8zi yes they’re supposed to be one in there too
@randy-yo8zi
9 ай бұрын
@Hunterworks Ok, thank you for your time. I will look into it. I'll look in to it tomorrow evening. Hate to keep bothering you guys. Im new at this rzr stuff🇺🇸🇺🇸
@sherri082772
5 жыл бұрын
I have a 2019 highlifter razor, i know it has a thicker or bigger belt, do i need to check for 2 blue washers?
@Hunterworks
5 жыл бұрын
For sure check
@michaelpayne9693
Жыл бұрын
What couses a 2007 danger at belt to have to be at higher RPM to engage an it also jurcks when it does engage please help.
@Hunterworks
Жыл бұрын
Worn out primary probably
@jaybenjamin9910
5 жыл бұрын
Will this blue washer trick work for 2018 Polaris sportsman 1000. It just destroyed the stock belt with 150 miles on it run 30 inch tires
@Hunterworks
5 жыл бұрын
To be honest I do not know, we only do UTV clutching so without a vehicle here to test. I can't say
@redskinman0
4 жыл бұрын
Love your videos! Very informative,I'm going to subscribe! I have 2016 Ace 900 SP ,would it need the blue washer? Thanks
@Hunterworks
4 жыл бұрын
I don't know without looking that one up, if just one blue then yes if you are a high speed rider
@AllThingsOffroad69
5 жыл бұрын
So just to be clear, my 2017 XP 1000 should have one blue washer installed already from the factory. You are suggesting adding a second to limit the range of the primary slightly?
@Hunterworks
5 жыл бұрын
That is correct
@AllThingsOffroad69
5 жыл бұрын
Cool where can I get one?
@Hunterworks
5 жыл бұрын
@@AllThingsOffroad69 polaris dealer of if you call an order in, we can put one in your order for $5
@AllThingsOffroad69
5 жыл бұрын
Awesome! I’m going to order one of your belts. I didn’t see the washer on your website. Great videos! Thanks
@tommydmot7725
3 жыл бұрын
Is there a way to monitor the temp of that belt? Edit: In real time
@Hunterworks
3 жыл бұрын
Yes, with a belt temp gauge we sell uses infrared beam
@gilbro1978
5 жыл бұрын
I was just looking at your belts and I have. 2014 1000 and do you recommend the standard or thick?
@Hunterworks
5 жыл бұрын
Depends on riding style, fast std, slow thick
@keithontrent5320
2 жыл бұрын
My transmission on my Polaris Ranger UTV is getting to hot causing my secondary clutch to blow belts and melt the buttons in the clutch
@Hunterworks
2 жыл бұрын
Never heard of that but get that tranny fixed
@EdwardJackson-qz9pk
Жыл бұрын
What is the best belt can-am camander
@Hunterworks
Жыл бұрын
Ours
@bmerrittful
5 жыл бұрын
I have a 18 general 4 I recently bought but am upgrading the clutch because of 32” tires. Are the generals common for needing the blue washer as well? Also looking to invest in the blower and temp sensor
@Hunterworks
5 жыл бұрын
You could check the travel and see but have not heard of them being an issue
@eduardoaraiza4069
2 жыл бұрын
this apply to a xp turbo 2017?
@Hunterworks
2 жыл бұрын
Kinda. We have a turbo specific video for that
@michaeldague3578
Жыл бұрын
WILL THE WASHER WORK ON A 2014 POLARIS RZR 570?
@Hunterworks
Жыл бұрын
Not needed and no sir
@AAllen-ze1zw
3 жыл бұрын
Todd I have a 2020 Xp 1000. Do you still recommend the BlowHole fan? If so is there one that would fit mine and plug in
@Hunterworks
3 жыл бұрын
yes still a good idea, same one fit them all, plugs into the tail light
@EdwardJackson-qz9pk
Жыл бұрын
Whats the best belt I can I am commander one thousand nineteen model
@Hunterworks
Жыл бұрын
Our belt. We have just one.
@alexciatti6386
5 жыл бұрын
Is this the same on a 2017 xp4 turbo. Mine did have any blue washers on it.
@Hunterworks
5 жыл бұрын
Turbo is different
@alexciatti6386
5 жыл бұрын
So do I not need to do the blue washers or should I still do it as a precaution?
@Hunterworks
5 жыл бұрын
I can't say at all, no idea if it needs it or this would work in a turbo
@adriansoria8661
5 жыл бұрын
Will it work on a 2012 Rzr 900 xp4. I keep blowing belts. So I just added the Blow Hole Fan but haven't tried it out. Is there anything else I can do to stop busting belts ?
@Hunterworks
5 жыл бұрын
I would need more info, email at todd@hunterworks.com
@wpslawnmaintenancellc9617
2 жыл бұрын
Where can I order that blue washer ? I have the stock 2017 xp 1000 , the belt blew about three times now
@Hunterworks
2 жыл бұрын
Probably not just a washer but we sell our own STD white washer, same as two blue. Shoot me an email todd@hunterworks.com and I can help you find your issue
@DemBallBoys
4 жыл бұрын
Will this be a good idea to add on my 2019 sportmans xp 1000 both washer and belt?
@Hunterworks
4 жыл бұрын
DemBallBoys we don’t offer a belt for it and never checked over travel on one. Sorry
@joselebron6049
5 жыл бұрын
I have a 2018 rzr 4 900 would I need to check for washer
@Hunterworks
5 жыл бұрын
Probably not, mostly just the XP 1000 and other 1000 vehicles
@travismaruagha7450
5 жыл бұрын
You should do some stuff for can am
@Hunterworks
5 жыл бұрын
True but I don't know much about them and no access to one.
@dannyboyrides4507
4 жыл бұрын
hello what washer did you use? and where can i buy them?
@Hunterworks
4 жыл бұрын
One and us
@dannyboyrides4507
4 жыл бұрын
Hunterworks Inc. i remove stock washer and use a blue one from you guys right? overall just 1 washer
@Hunterworks
4 жыл бұрын
@@dannyboyrides4507 This video is old, there is a newer one, we have our own washer, twice as thick as one blue. In this video we said use two blue, now one std washer from us
@dannyboyrides4507
4 жыл бұрын
Hunterworks Inc. got it, i have a 2016 rzr XPT, what washer and belt would you recommend? i see you guys have 2 washers on your website
@MrJake81283
4 жыл бұрын
If I never blown a belt. Should I add the second washer?? Have stock clutching.
@Hunterworks
4 жыл бұрын
You are probably not a high seed for distance guy. This is a old video, we make our own washer that is as thick as two blue
@MrJake81283
4 жыл бұрын
Hunterworks Inc. okay thanks. Going to be ordering the secondary rollers soon.
@georgeflensburg3087
5 жыл бұрын
Will that washer in the Primary clutch work with a 2007 Polaris Ranger 700 6x6 EFI?
@Hunterworks
5 жыл бұрын
Maybe but it does not need it
@forcedtosignup2
4 жыл бұрын
Does limiting that throw with the blue washer limit top end speed?
@Hunterworks
4 жыл бұрын
professional motion not sure what you’re asking but adding a second blue washer or now our std white washer in their place does not affect top speed. Seems like in video I mention I ran 85 with them in there
@j.ewilkinson9294
4 жыл бұрын
I have an 09 700 ranger. It just bucks when you put it in gear. Quits if you keep pressing gas. Any ideas?
@Hunterworks
4 жыл бұрын
What do you mean it bucks. Explain, you put in gear do not touch the gas and it does what?
@j.ewilkinson9294
4 жыл бұрын
It's like you put it in gear and give it a touch of gas, then it acts like it is stopped by a brake, then back in the gas, then on the brake again without ever touching the brakes. Takes about 10 minutes to go 25 ft
@Hunterworks
4 жыл бұрын
@@j.ewilkinson9294 That is a weird one but that is in the primary clutch, watch our how to troublshoot a primary clutch video
@Dooguy
3 жыл бұрын
Does this pertain to 900 rangers too. ? Blue washer wize
@Hunterworks
3 жыл бұрын
No sir
@howardmiller4241
4 жыл бұрын
I just bought a 2020 rzr 900 s will this work on my new rzr ?
@Hunterworks
4 жыл бұрын
Typically not needed on 900 but swapping out the square pucks in the secondary for our round ones is still a no brainer
@victorazukas4344
2 жыл бұрын
Do you need one or two blue washer on this replacement
@Hunterworks
2 жыл бұрын
Neither, our std white washer is the only one you need
@jevonthomas2373
5 жыл бұрын
Will this make a difference on 570rzr or just the bigger ones
@Hunterworks
5 жыл бұрын
Jevon Thomas does not affect the 570.
@scottyknemeyer381
2 жыл бұрын
Will this work for the can-am maverick x3?
@Hunterworks
2 жыл бұрын
I’m sure some applies
@jakebarnier5188
4 жыл бұрын
Any after market companies making a fan for belt housing?
@Hunterworks
4 жыл бұрын
We do, look on our site
@jakebarnier5188
4 жыл бұрын
What is your opinion on not using the belt cover?
@Hunterworks
4 жыл бұрын
jake barnier too much dirt
@perez9444
4 жыл бұрын
2019 turbo s rzr xp4. Can I use the Blue washer?
@Hunterworks
4 жыл бұрын
No we have a black one and whole another video on it.
@jimrachels9372
3 жыл бұрын
Is the blue washer an issue for the pro xp??
@Hunterworks
3 жыл бұрын
No just non xp
@chadshumaker2789
5 жыл бұрын
Does having the blue washer in there effect the top speed at all as it limits the primary and secondary movement?
@Hunterworks
5 жыл бұрын
No, too small of change, puts belt where it should be
@chadshumaker2789
5 жыл бұрын
@@Hunterworks awesome. Thanks for the reply. Just wanted to check
@lainekennedy941
4 жыл бұрын
Will your white washer help a 2020 Turbo?
@Hunterworks
4 жыл бұрын
Laine Kennedy no it’s not for turbos. Our black washer is. Go to our site then turbo rzr page you will see it. There is also a video here on our channel about it
@gregorypollet2194
4 жыл бұрын
Would this apply to RS1 as well
@Hunterworks
4 жыл бұрын
Not to my knowledge and it has the turbo clutch on it or turbo style
@matancherhe5642
Жыл бұрын
will it fit rzr 800s 2010
@Hunterworks
Жыл бұрын
no and no need for it
@matancherhe5642
Жыл бұрын
@@Hunterworks 👍👍👍👍👍
@ve3xtr
5 жыл бұрын
I stopped blowing belts by selling the RZR and buying a Honda Pioneer. Yes, I know....low HP, but HP is nothing when you're broken down in the bush. NO belts on a Honda to blow. Shaft driven. Why doesn't Polaris put a shaft drive in their machines? It's because Honda holds the Patent on their shaft driven system. Good video though.
@Hunterworks
5 жыл бұрын
I have only blown one belt and it was my fault and have had a ton of Polaris and you could not give me a Honda, the transmission go bad in those all the time too. But please take no offense the videos are to help owners of the vehicles, selling it and getting nothing fixes the issue too but that is not what these videos are about.
@ve3xtr
5 жыл бұрын
@@Hunterworks No problem
@BillyTpower
3 жыл бұрын
this fix is for rzr 1000 . do I need this on my ranger 900?
@Hunterworks
3 жыл бұрын
no sir, it should not have a temp issue
@BillyTpower
3 жыл бұрын
@@Hunterworks thanks man, hey did u just make your own use or do u sell the heat gauge?
@Hunterworks
3 жыл бұрын
@@BillyTpower Heat gauge? If you mean belt temp gauge we sell them, rare for a ranger owner to buy one
@alejandroquiroz3251
3 жыл бұрын
So do you recommend one or two blue washers on at the same time
@Hunterworks
3 жыл бұрын
Neither, I recommend our STD washer, same as two blue
@march966
2 жыл бұрын
@@Hunterworks does white washer in dalton kit do same thing??
@Hunterworks
2 жыл бұрын
@@march966 no most of their kits that’s a secondary spring.
@march966
2 жыл бұрын
@@Hunterworks ok tks cause i put dalton mine remember was white teflon washer but i had it installed so i wouldnt know
@ralanis77
5 жыл бұрын
would that work on a 2016 RZR Turbo
@Hunterworks
5 жыл бұрын
No, meaning the blue washer
@ReDNeckRoY
5 жыл бұрын
Does this apply to the Turbo or XP1000. Couldn't find anything on you're site. Thx
@Hunterworks
5 жыл бұрын
Ben Gordon this video does not but we have a video on the same thing for a turbo and black walker for them. They are on our turbo page
@ReDNeckRoY
5 жыл бұрын
@@Hunterworks can't find any video on the washer that has to do with 2018 Turbo. I bought 2 blue washers because I thought you were working on a Turbo.
There is the link to the black washer on our site for a turbo and there is a video link on that page too. Not sure how you got that this video was about a Turbo. Without watching it again myself I don't think a turbo is ever mentioned
@ReDNeckRoY
5 жыл бұрын
@@Hunterworks I must be computer dumb because I can't find the video.
@quadkor11
4 жыл бұрын
Where do you buy these blue washers?
@Hunterworks
4 жыл бұрын
Old video, we have the replacement, a STD White washer on our site, same thickness as two blue
@quadkor11
4 жыл бұрын
@@Hunterworks ok thank you!
@dieseldev7
4 жыл бұрын
Does the blue washer apply to the 2019 turbo S?
@dieseldev7
4 жыл бұрын
And what belt do you recommend for that unit?
@Hunterworks
4 жыл бұрын
Devro777 no we have a black washer for turbo and we recommend our belt
@dieseldev7
4 жыл бұрын
Do you have a part number for both? I’d love to order them from you
I have a 2012 xp4 900, I just installed the Hunterworks fabricated white washer. It has made a world of difference.
@calebriley8920
5 жыл бұрын
I have a 2018 xp1000. 40hrs. I put your secondary rollers on right when I bought it. I haven't been having an issue with belts. Should I still install an additional washer?(assuming I already have one currently in my primary)
@Hunterworks
5 жыл бұрын
Up to you, if you drive fast a lot I would
@Hunterworks
5 жыл бұрын
If not no but it can't hurt
@jasonmorris355
5 жыл бұрын
Will this work on a 2013 ranger 900 xp?
@Hunterworks
5 жыл бұрын
no sir, it dos not even have a spider nut that is under the washer
@summitdave8782
5 жыл бұрын
Yo have any belts for a 2018 RS1...Thanks..or Washer...
@Hunterworks
5 жыл бұрын
Summit dave www.hunterworks.com/inc/sdetail/96685/96896
@Hunterworks
5 жыл бұрын
Summit dave no washer needed on a rs1
@summitdave8782
5 жыл бұрын
Is that cuz there is one or just dont need it..And thanks...
@summitdave8782
5 жыл бұрын
Wow you did have one..I even looked at your page before asking you...lol
@Runnfreeyeah
4 жыл бұрын
?, I assume this fix works for the Polaris Ranger class as well??
@Hunterworks
4 жыл бұрын
Not really applicable to them
@TwistedOff
Жыл бұрын
👍
@dansloan4242
5 жыл бұрын
Uh huh huh, Beavis.... He said finger control!!!! Hey pull my finger!
@grasscutter88
3 жыл бұрын
Spray foam in that building.... Glad I never went that route.
@Hunterworks
3 жыл бұрын
Glad I did, it is amazing stuff
@grasscutter88
3 жыл бұрын
@@Hunterworks I did mineral wool and don't have any echo.
@Hunterworks
3 жыл бұрын
@@grasscutter88 oh, thought you meant for insulating, yeah there is some echo
@jorgelopez3922
5 жыл бұрын
How do u keep belt from slipping when going through water?
@Hunterworks
5 жыл бұрын
Jorge Lopez keep water out is only way
@jorgelopez3922
5 жыл бұрын
@@Hunterworks lol. I'll keep that in mind. Thanks brother
@gwood701
5 жыл бұрын
If you need this guy to fix a machine that came from the factory as a piece of crap then you bought the wrong machine. Polaris are poorly designed. Plastic cvt cover that warps and lets water in? Wtf! Then its $2000 for a new primary lol
@lastcoyote2355
2 жыл бұрын
Having been a millwright for 35+ years … there is a reason for following torque spec’s . It drives me crazy when someone makes a comment that the know the feel of their impact tool . Sure it hasn’t happened yet … 1 year … 15 years … but it will happen, either a broken screw / bolt or worse cracked housing . Ending my subscription….. Bye 👋👋
@Hunterworks
2 жыл бұрын
Bye. I’ve been a clutch guy for 19 years the broken bolts were from torquing. It has its place on some but on this one no good way.
@Hunterworks
2 жыл бұрын
Simple question, how would you hold this primary while torqueing it?
@Hunterworks
2 жыл бұрын
This is why we do this, got this email today "I saw on one of your videos that it’s common to break one or more of the 6 bolts off in in the primary by using a torque wrench"
@frank23103
2 жыл бұрын
Using an impact on something that requires 7lbs of torque is just bad advise- might have worked for you- but to tell people “finger control” is simply lazy nonsense. Pull out your torque wrench and do it correctly if your going to make KZitem videos… just sayin…
@Hunterworks
2 жыл бұрын
Way more broke these with torque wrenches than an impact. 19 years no one has reported broken with impact. Tons with torque wrench. I’ll keep doing it this way.
@MikesDIY
5 жыл бұрын
5438963 (Part number to copy and paste)
@Hunterworks
5 жыл бұрын
OliveAbortions we have our own washer now if that’s the part number for blue washer
@Hunterworks
5 жыл бұрын
hunterworks.com/inc/sdetail/56301/109223
@christophergreen6861
Жыл бұрын
washer and hunter belt needed for 23' Rxr XP4 1000???
@Super-no1fx
10 ай бұрын
Do you need the blue washer if u start running the hunterworks belt?
@Hunterworks
10 ай бұрын
The washers have nothing to do with what belt is on there. Our std washer fixes the overtravel issue with the clutch
@Super-no1fx
10 ай бұрын
@@Hunterworks thank you.. I thought I heard somewhere in the vid that the hunterworks belt was part of solving the belt problems
@Hunterworks
10 ай бұрын
@@Super-no1fx I’d have watch myself. This video is four years old. Things have changed since to some extent
@Super-no1fx
10 ай бұрын
@@Hunterworks ur time is appreciated.. thanks for your very informative vids.. I’m getting some heavy jerking and perhaps belt slippage in a gen xp4 1000 I picked up with 500 miles.. no where near as smooth as my razor ..off hip I gather belt check followed by checking spider nut ?
@Hunterworks
10 ай бұрын
@@Super-no1fx send me an email on this one todd@hunterworks.com
Пікірлер: 210