Blog post with more info - www.howtomotorcyclerepair.com/synchcarbs Buy the Prop-Tech Dsynch2 - www.howtomotorcyclerepair.com/proptechdsynch2
@fenrir1701
2 жыл бұрын
Fantastic video. I’ve spent ages trying to find an in depth video explaining carb syncing
@timtravasos2742
4 жыл бұрын
That takes special tools and talent. I can't imagine trying to use an old vaccum gauge set up.
@HTMR
4 жыл бұрын
A simple manometer tool works just fine as well.
@assessor1276
4 жыл бұрын
Lighting on your white board: try putting a light on the ceiling pointing directly at the whiteboard. As long as that light is brighter than the light behind the whiteboard (say from the window as in this video), the whiteboard should show up nice and clear.
@HTMR
4 жыл бұрын
Thanks for the suggestion. I have 2 softboxes, maybe I'll try lifting them as high as possible and aiming them directly at whiteboard.
@wobblysauce
4 жыл бұрын
or to the side, not in the reflection area of the camera.
@dntlss
4 жыл бұрын
Matt, the bike is looking beautiful,i bought one of your videos a while back to get started restoring the motor on my 550 but i have been too busy with life and other things, hope everything is going well with you and your family.
@ianmacgillivray2740
4 жыл бұрын
Great job on those carbs!! They look like new.
@timtravasos2742
4 жыл бұрын
Great job.
@timtravasos2742
4 жыл бұрын
Shine a light from above on the white board.
@HTMR
4 жыл бұрын
Cool thanks I'll try that.
@folerx
5 ай бұрын
nice video. same for fuel injected bike? what about gunson colortune tool?
@luis0luis058
Жыл бұрын
Exelent
@MrCoffeypaul
4 жыл бұрын
If using a drill bit it might be good advice to measure using the shank end? Absolutely beautiful looking engine totally jealous!
@HTMR
4 жыл бұрын
Yes, use the shank end.
@daveco1270
4 жыл бұрын
Great video. This might be a dumb question but when you do the bench sync with a drill bit, you have the carb spring attached to the linkage, right, so there's pressure being put on the drill bit?
@st-qd8wg
Жыл бұрын
MATT, I have last year carburetor and my throttle spring will not let my hand Lever go back like it should when I give gas I got do it manually instead plate go back once release hand Lever what do suggest that will help throttle plate snap back without replacing Lazy spring.
@Mototistampls
4 жыл бұрын
Matthew I want to purchase the video but I don’t want to buy the sync tool you’re showing on this video. Do you show other ways to sync the carbs on the pay video?
@Rededits1226
Жыл бұрын
Hi. What cause a carb overflow coming out of overflow pipe
@HTMR
Жыл бұрын
Either a worn/dirty float needle. Maybe even a cracked overflow tube: kzitem.info/news/bejne/24SA3quJe2emnKg
@NIGBEATS
4 жыл бұрын
Oi, I just got this sync tool and I've got a 1st gen Yamaha Vmax which is a V4. My vacuum ports are on both sides of the bike and the hoses do not reach without having to route them through the motor, in particular, close to the heads. Can I extend the hoses without causing a distortion in the readings?
@PropTechMotorcycleTuning
4 жыл бұрын
You can extend hoses. Dynamic of curves reduce, will not effect to adjustment. Use same length.
@sugarskulllyfe5890
Жыл бұрын
how the hell did honda techs do this in the 70s and 80s holy jesus!!!!!
Пікірлер: 25