Thank you very much for this so good Video, I have exaclty the same without any documentation and your video was very clear for me. Thanks again.
@zana3587
7 жыл бұрын
well come
@jusb1066
7 жыл бұрын
it is fused on both 10a and ma, so very good, plus tough case, i have seen this in (aldi/lidl) and think it is good value (i dont need though) plus battery test range, (this applies a small load to 1.5v and 9v batteries, if still above 1v or 6v then they are good). it will also measure over 250v (at least 600) but they do not want to you be unsafe so mark it as 250v (diode pipe=bridge rectifier, and will make voltage of ac transformer higher on DC). thank you for video once again Dahen, good wishes. (oh it is megaohms not micro ohms :)
@zana3587
7 жыл бұрын
thank you for information - you good
@azergezalov5032
3 жыл бұрын
Спасибо. Жаль что не на русском языке
@zana3587
3 жыл бұрын
Спасибо, сэр
@traviskeegel9404
6 жыл бұрын
Thank you for you informative video, I did learn a lot it was Brilliant
@zana3587
6 жыл бұрын
+Travis Kee welcome man any time
@nunomascarenhasribeiro
6 жыл бұрын
Helo...My BATT position doesnt read.....is it the fuse??
@zana3587
6 жыл бұрын
+Nuno Ribeiro Check the Fuse by another multimeter. In a few multimeters there is wire instead of fuse. Check the wire
@nunomascarenhasribeiro
6 жыл бұрын
dahen zana my multimeter is exactly the same in the video
@zana3587
6 жыл бұрын
+Nuno Ribeiro It's a good multimeter
@zana3587
6 жыл бұрын
+Nuno Ribeiro Is it not working permanently or some of the Function does not work?
@nunomascarenhasribeiro
6 жыл бұрын
dahen zana both fuses dead...all ok now. But COMM and Vcont. Worked fine with both fuses dead..?..
@korbendallas9689
2 жыл бұрын
Good review. I have the same multimeter but when I try to do the continuity test, the multimeter doesn't beep sound, the buzzer sound. What could be the problem?
@russflynn2084
2 жыл бұрын
Do you have the pos+ lead in the mA/Ω/BATT socket ?
@korbendallas9689
2 жыл бұрын
@@russflynn2084 thanks for the reply. After speeding few minutes around the device, I found out that there is a beep sound after all, but it's really low, I had to put the multimeter close to my ear to listen... I think it's common issue on these multimeters. But that issue aside, everything else is working perfectly.
@boudig
7 жыл бұрын
très bonne vidéo comme d'habitude merci du partage
@zana3587
7 жыл бұрын
Merci - vous l'homme vraiment scientifique
@rahimrahim-om5jj
2 жыл бұрын
شكرا شكرا
@zana3587
2 жыл бұрын
شكرا اخى
@rangerdd
7 жыл бұрын
thank you so much, very helpful video, Merci,,
@zana3587
7 жыл бұрын
thank you
@rangerdd
7 жыл бұрын
just one question, the buzzer sound has gone on my powerfix multimeter, has a fuse inside blown.. thank you,
@zana3587
7 жыл бұрын
I will make sure tomorrow I will send yo
@rangerdd
7 жыл бұрын
thank you..
@zana3587
7 жыл бұрын
There are two fuses inside the multimeter but there is no connection between the fuses and buzzer - Check the connection (red wire and black wire) between the buzzer and the bord
@tecnisdaimondm.g9321
Жыл бұрын
Excelente 👌
@gkshighfalutintubeexperien8205
7 жыл бұрын
I have this 😀😀😀
@zana3587
7 жыл бұрын
+Grigoris Katsimihas good
@zana3587
7 жыл бұрын
+Grigoris Katsimihas good
@gkshighfalutintubeexperien8205
7 жыл бұрын
dahen zana look my last video ☺☺☺
@zana3587
7 жыл бұрын
I see you have a problem with your multimeters screen
@zana3587
7 жыл бұрын
When you sent the message to me I was checking the car's control by powerfix multimeter
Пікірлер: 40