same here! that is probably the most helpful guide ever! I ordered 2 wheels and changed them.. all good now! thanks a ton!
@btsh.t7873
Ай бұрын
Screws... Screws...... More Screws...... omG! Like Dismantling the turtle from ItS SheLL. But the. Again $Super.Informative! Thank You for this Educational Video! 🙂↕️
@bradyr7227
Ай бұрын
Excellent video. Every step was very well explained. The only issue I had was that my top panel has one of those ZIFF connectors and I think I pulled it out the wrong way and now it will not lock back down over the data cable. Hopefully some hot glue will keep it in properly.
@DeanJohnson-v1l
Ай бұрын
You my man are a legend. Thanks for the guide finally have my robot back up and running.
@yaasser88
Ай бұрын
That’s very helpful thank you finally I replaced my old wheel 😅😅😅😂 ,, what takes 20 minutes video it took from me around 2 hours 🎉🎉
@ughrew
4 ай бұрын
Good news, now i know to dismantle the wheel. Bad news. I have to open everything 😮😢
@atinchaudhary942
2 ай бұрын
Great demo, buddy. You have given a detailed run down...well done
@DJ-wi9yk
8 ай бұрын
I totally just replaced the left wheel on my deebot. Thank you for your excellent tutorial. Did I have a screw leftover that I don't know where it goes? Yes, yes I do. But my deebot is fixed and no longer travelling in circles like a dog chasing its tail. Thank you 🙏
@crakkstuh
Ай бұрын
thank you buddy, I was able to repair my t9 pro
@lynnlotus2942
3 ай бұрын
Very thankful for your video. I followed your video and replaced one wheel on my Ecovacs Ozmo T8. However, during the process of putting it back together, 2 identical springs (4 mmOD x 5mm) accidentally dropped out. I couldn't figure out where they came from so I couldn't put them back. Now when I try to put the vacuum back in service, I get the message that the anti-drop covered with dust. what did i do wrong? Please help!
@Acab666
Ай бұрын
Did you get the problem solved ? Because I faced same issue with you. Where should I install this spring? 🙃🙃🙃
@rajdude1
Ай бұрын
Thank you very much for this video. Using your instructions, I just replaced my left wheel motor. But now it keeps saying "please clean my anti drop sensors". It was working fine before I opened it. While putting it back, I noticed I had pinched some wires, and it's case was not fully closing. I fixed the issue and was able to properly close the Deebot's case. Do you think there is a chance I cut the sensor's wire?
@EnricoChinaglia
6 күн бұрын
Hi, thanks for sharing this video. I have Deebot OZMO T8 Pure and I need to replace both wheels, can you suggest me the right spare part sending the eBay link page? Thank you.
@greenyblueeyes1
11 ай бұрын
Had the same problem! Because it was predominantly moving in a right circular motion, I replaced the R wheel drive (this was suggested in Ecovacs service videos on KZitem). This did not solve the problem however. I then checked the L wheel drive and found one of the two wires leading to the wheel revolution sensor on the L wheel drive had broken. This was resoldered and solved the erratic motion and 'check wheel drive' error. Hope this helps someone.
@chaoticstylez
Ай бұрын
For the cost of the wheels on Amazon I was able to purchase a new lesser model from eBay that already has lasted longer than the original.
@thomashonlam
6 ай бұрын
Thanks a lot for the great video! My X1 Omni won’t return to the station as it backs up more to one side. I turned it upside down like you said and I found the resistance between two sides are very minimal. Should I replace the wheels or there’s anywhere I should check? I’ve only used it sparingly for 15 months. Thanks!
@sabrinacompan
7 ай бұрын
Thanks à lot for this video I've fixed my wheel problem with it
@AlexandrSKYTRASH
3 ай бұрын
Good tutorial! I replaced both wheels. But in the first clean robot stopped during the process and is not showing as online. Is it possible to give it to you for service or how to get in touch with you?
@stefanoazzi8425
11 ай бұрын
Very thankful for your videos!! Congrats!
@ecovacstechnicalsupport5278
11 ай бұрын
Welcome
@thegreatescape07
4 ай бұрын
Great video!! Thank you
@EVOLVED-q1q
25 күн бұрын
Hi..we have N8 pro +. I opened it since it moves to left circle quickly and stops and says please check the driving wheel. There's absolutely no issues with motors on either side...what am i missing? Please help me... thank you Shubham...we spoke last year...😊 thank you 👍🙂 do you think its planned obsolescence? Software?
@mattsayers8565
24 күн бұрын
I have replaced BOTH motors and still have the same issue with the right wheel simply not turning and the “please check the driving wheels” error. Is there anything I can do to fix it or is it a failure built into the software since it’s out of warranty?
@kellygentle2210
Жыл бұрын
Hi, We're very thankful for your videos. We've just replaced the wheels on our ozmo 950 and still getting 'driving wheel malfunction' error. Our front bumper appears to be sticking on the right hand side. Could this be contributing to the error as the device is pushing up against furniture when it errors. Appreciate any advice.
@ecovacstechnicalsupport5278
Жыл бұрын
Plz WhatsApp me a video clip at 00601137973018...let me see the video then I'll reply...now I'm in hospital for dressing..next is my turn 😅
@MightyPorcupine
6 ай бұрын
@ecovacstechnicalsupport5278 thanks for this detailed tutorial. I've successfully changed the wheel, and the vacuum is working fine for a little, and then the wheel is stuck again (hard to rotate). I turn it off and on, and then it is working fine again, for few minutes, and then it repeats itself. It seem like I have a bigger issue. What could it be? Is there other component that controls the wheel that might be defective? I would appreciate your help
@shamsso2210
Жыл бұрын
Where can I find a motor assembly for a deebot ozmo t8+? I followed your steps and was able to clean the motor assembly which was very dirty, I also cleaned all the gears and reapplied silicon grease. After putting back i can hear the sound of the motor turning but the gear is not totally in contact with the next gear making a high frequency clicking sound.
@ลุงลมคนทํามาหากิน
3 ай бұрын
ใช้งานดีไหมประเทศไทยไม้มี
@dardashnaa9541
Жыл бұрын
Amezing video as usual 👍👍
@ecovacstechnicalsupport5278
Жыл бұрын
Welcome
@senemdemirel7798
4 ай бұрын
Thank you very good video
@mlpokjn1
3 ай бұрын
Hello, I had issues with my deebot 950 - spinning around all the time. So I checked wheel and it was burnt as you mentioned in video. I replaced wrong wheel and robot is doing well in begining of cleaning, cause Issue still persist after one cycle of cleaning. Replaced wheel is once again stucked. I noticed that off / on always help. Wheel is released and moving normally. But I do not want to do it after each cleaning. Can you help me?
@poulstindavis9939
2 ай бұрын
Hi I have a question, the right wheel wasn't working i mean it was rotating clockwise, which i fix with your instruction using WD spray, now its start moving however after 2-3 minutes the deebot goes crazy moving fast hitting everywhere rotating fast, after rotating manually the wheel it starts moving with no issues for 2-3 minutes and then shows the same issue again, what might be the problem, do i need to replace the wheel. Thanks
@nampri
9 ай бұрын
thanks a lot of the video! I managed to open my deebot ozmo 950, but can't put the new wheel back to make it " jumping", could you please suggest how to do it on ozmo 950 model specifically? it is quite different from the one you show? and my be also how to open another wheel? it also looks quite different, at lest on 950. Thanks in advance!
@ecovacstechnicalsupport5278
9 ай бұрын
In this week I'll upload video about Ozmo 950 sir at ur request
@nampri
9 ай бұрын
that would be awesome, thanks a lot!
@nampri
9 ай бұрын
@@ecovacstechnicalsupport5278 hello! do you think you will have time to make this video during upcoming days? Thanks and happy new year! :)
@Akshay-r8s
7 ай бұрын
Where can we buy the spare parts ?@@ecovacstechnicalsupport5278
@michaelfsantos22
Жыл бұрын
Great video, but is there any way to change only the motor? I have soldering skills, but I can't find the same motor anywhere. Do you know any compatible motor for the wheel (do you know voltage and rpm)? Here in my country a complete wheel cost almost half the price of the robot! 😢
@ecovacstechnicalsupport5278
Жыл бұрын
Just remove the motor..all details printed outside the motor assembly... motor same is quite difficult..but Carbon brush u can try to replace... hopefully will fix the issue...
@ecovacstechnicalsupport5278
Жыл бұрын
Because In motor always carbon brush burn that's all
@DebHeadworth
2 ай бұрын
Thank you!!!!!
@yog1373
3 ай бұрын
Hello do you have the goat g1 lawn ? I got a problem with it
@ecovacstechnicalsupport5278
3 ай бұрын
Sorry don't have
@sidi4622
Ай бұрын
The moment you realize that Ecovacs intentionally made it very hard to exchange anything. Never going to buy a Ecovacs product again!
@MaryamGorg
26 күн бұрын
Same. Im not buying ecovacs ever again & will keep telling people around me to not buy this
@Stvnalln1
Жыл бұрын
I keep getting the off the floor error message after cleaning my Deebot Neo. Any advise on how to fix?
@kutgoogle9979
6 ай бұрын
Super helpfull
@MauroCanossi
Жыл бұрын
Hi I ned help on my X1 omni the pad not spinning , looks like some thing are loose, have a video haw to open for ceck inside at X1 omni thanks for help
@ecovacstechnicalsupport5278
Жыл бұрын
For omni X1 not yet done videos...but now soon I'll start about Omni issues
@subodhbhoraskar8431
Жыл бұрын
where you are ? I am in INDORE want to repair my Ecovacs
@ecovacstechnicalsupport5278
Жыл бұрын
Hi..I'm living in batu caves Malaysia..if you are in Malaysia you can contact through WhatsApp 00601137973018
@joscelinalvina1228
Жыл бұрын
hi, i have checked the driving wheel and none are stucked inside.. may i know if i can send my deevot to tou for fix? thanks
@ecovacstechnicalsupport5278
Жыл бұрын
Yes sure...plz bring at given address...Amara residence block A, floor 19, unit 06. Once reach rhere you have my contact no. Can call me I'll be there to receive
@cf3572
3 ай бұрын
can someone help me? i while turning it upside down, a small part just fell out of the robot. (t8), it is around a centimeter big and has two square holes in it. it says A4 on the part. i just cant figure out where this part belongs... help :D
@rajdude1
Ай бұрын
yeah, I had the exact same problem and I spent around an hour trying to figure it out. So that part goes onto the 2 USB ports on the control board. It is on the right side. You can see that it will fit the ports. It has two round prongs which go into the system board and also has a latch on left side, which engages with a slot on the board.
@GeraldScholz
Жыл бұрын
Perfect timing since my wheel broke yesterday
@ecovacstechnicalsupport5278
Жыл бұрын
Welcome
@MrRes1cue
10 ай бұрын
So is the only reason the larger battery can't be used in the N8+ is because of the metal weight cover being different?
@ecovacstechnicalsupport5278
10 ай бұрын
Not Only the Mattel plate..place of battery also designed accordingly..other models can not fit
@juliomassaneiro5793
Жыл бұрын
Boa tarde! Como eu desmonto o n78
@clavelolivier8329
9 ай бұрын
where can i find this wheel?
@ecovacstechnicalsupport5278
9 ай бұрын
Please check online sellers like Ali Xpress Amazon etc
@muralimohan9524
9 ай бұрын
Travi Error 6: Device Stuck or Trapped Device may be suspended in air. Move it to a new position close to the original position and try again. If the device is still unable to start, clean the edge sensor and try again. please help sir
@ecovacstechnicalsupport5278
9 ай бұрын
Plz WhatsApp me a video clip so I can confirm what's the issue...00601137973018
@abelsijo8839
Жыл бұрын
hi i replaced both wheels but now it is saying after i put everything back “please clean my anti dust sensors”
@ecovacstechnicalsupport5278
Жыл бұрын
Plz check have you fix the all the wires....or plz check weather sensors got any rust sign...
@ecovacstechnicalsupport5278
Жыл бұрын
How to replace anti drop Sensors ... video available.can get help from that
@abelsijo8839
Жыл бұрын
@@ecovacstechnicalsupport5278 ok thank you will try
@abelsijo8839
Жыл бұрын
@@ecovacstechnicalsupport5278 hi again i fixed the “please clean my anti drop sensors” after making sure all the wires were connected, but now sometimes the bumper gets stuck
@abelsijo8839
Жыл бұрын
never mind i fixed it. Thank you so much for these videos. My deebot ozmo 920 is nearly 3 years old now.
Пікірлер: 76