Score it first with a sharp utility knife. Keeps the paint from chipping and won't need to touch up with paint.
@Dumbass_mechanic
5 жыл бұрын
Fyi I picked up the same tool at harbor freight for $20. Yeah it isn't Bosch, but it did the job. The pull saw was $15 at menards.
@judichristopher4604
3 жыл бұрын
Are you serious... $20. because I didn't see it there!!! How did you get it for only $20.
@chipblanc6037
2 жыл бұрын
Same! Been using it for baseboard, door frames and plunge cutting into walls for several yrs with no issue
@garrettbirkel7750
7 жыл бұрын
I enjoyed how the music is in the same key as the cutting noise :D
@Nitrogenb
6 жыл бұрын
Same!
@brygonie
6 жыл бұрын
Garrett Birkel b
@charlesbonkley
3 жыл бұрын
Could have been intentional, or by accident. Either way, it was cool...even building up volume before it stopped!
@lauriewhite9083
6 жыл бұрын
Thank you! We were stuck on this dilemma with a do-it-yourself home improvement project. We are going to buy one of these tools in the morning! Hope ours turns out just as nice!
@MAli99923
6 жыл бұрын
Better to do it with a handsaw, empirically speaking a much cleaner cut.
@rickherrick1732
6 жыл бұрын
I was pointed to this video by another vendor to show me how to use the undercut blade on a project I have. This was a very, very well done video with regards to this technique. And it will help me down the road when I actually do have to replace some flooring. Thank you.
@BillB
6 жыл бұрын
Roberts makes a jamb saw just for this (with a circular blade and adjustable height foot). A reciprocating saw is ok to do a few with but it's loud and quite slow. Bits are also expensive and as you see in the video as they begin to dull they'll burn the wood and cutting gets even slower. For a one time diy-er this is a great instructional video though. Good job!
@brianandkaylamiller4705
6 жыл бұрын
Man that tool would have been great to have when I laid my laminate floors. I used a drywall saw to cut all those door frames.
@sagarmatha29
4 жыл бұрын
you saved me a massive headache in small cuts, thanks!
@michaelrobinson4677
2 жыл бұрын
Thank you, going to do my first floor. I'm hoping my Robyi oscillating will work.
@barbaradixon6106
8 жыл бұрын
Thank you. I did not realize that I already have the proper tool that I need to cut out the casing.
@_BAD_MERC_
4 жыл бұрын
Thanks for the amazing demonstration and clear example.
@BigCheese85
4 жыл бұрын
Did you cut all the way under the rest of your skirting like that to prevent having to remove before fitting the floor? Thanks
@trebelclef
7 жыл бұрын
I have been looking for that tool a long time, Home Depot and Lowes never know what I am asking for, not found it yet...Great video, thanks!
@williamscott872
7 жыл бұрын
trebelclef oscillating saw
@woolywonders5546
6 жыл бұрын
Got mine from Walmart. They also sell additional blades.
@karengp162
5 жыл бұрын
Thanks for the video. Wow, I'm going to have to redo the door jambs I've done. Mine are a mess, and I need to get that tool before I destroy the rest of the house. I was using the japanese pull saw (what a pain that is) and I don't know if the blade got dull right away but I couldn't get deep enough under the jamb.
@premyo4u
3 жыл бұрын
Watching until end to know how you fix something. New friend from Canada
@Mushir000
4 жыл бұрын
Excellently presented and provided me solution. Stay healthy and blessed. Thanks again.
@AndrzejJeczen
4 жыл бұрын
Thanks for that. Do I use the same technique if I want to install boards along a narrow landing and there are two sets of doors opposite each other on both sides (left and right) of said landing? I want to install the boards along the landing so then I can continue to the living room. Thanks.
@heatherjohnson955
2 жыл бұрын
Awesome. I have an 1885 Victorian with beautiful baseboards and casing and I did NOT want quarter rounds. Now I have to find someone skilled to do this. 😬
@rcjunkin2222
5 жыл бұрын
Thank you you saved my Christmas dinner
@stargate0619
Жыл бұрын
what do you do with the opposite problem? I have old floors to replace which will create a large gap between the door casing and flooring. Same problem with the baseboards, a large gap between the flooring and baseboard.
@judichristopher4604
3 жыл бұрын
What is the name of your flooring? And where can we buy it? Thank yoyo much for sharing this great video. Great Filming and Editing too!!!
@dmitrikguajardo6006
6 жыл бұрын
i do all my undercutting before i lay under layment so i dont leave saw dust and wood chips under the under layment
@ombligoapestoso5600
4 жыл бұрын
Smart
@alyshatetens6672
6 жыл бұрын
This video was very helpful. It was easy and clear to see what you were demonstrating. Thanks very much. I thumbed up the vid.
@resourcefulgirl
4 жыл бұрын
Project help needed! I hope you or a subscriber can assist me. I have a formica countertop which is a one piece, countertop and backsplash, similar to the ready made countertops at the big box stores. It looks dated to me and I want to keep the countertop, cut off the backsplash, seal and epoxy the countertop and finally, tile the wall. Would this tool be good for a flush cut and removal of the backsplash? Thanks so much!
@xl000
6 жыл бұрын
but how deep can you cut ? I assume this part of the casing transfers the weight of the casing and door to the floor ?
@Oscaro9928
6 жыл бұрын
What was the brand and color of the flooring, my wife loves it and we are thinking of putting down new flooring in our house. Thanks and great video
@judichristopher4604
3 жыл бұрын
I wished I knew that too...
@BeccAcCardenas
4 жыл бұрын
A reason to buy another tool, awesome.🤘🏻
@ItaloRican7
5 жыл бұрын
Thanks for sharing. Fantastic video!
@panchitomontero9051
5 жыл бұрын
Nice, what would you recommend to do the same cut on a metal frame?
@faradpack
8 жыл бұрын
thank you, my question is if I do not remove molding from wall base, is there a trick to cut it without moving the molding using a hand saw, Japanese
@larrystehura3862
5 жыл бұрын
Thank you! Well presented! Keep sharing your experiences!
@13salinaspride
3 жыл бұрын
Do I gotta use a 1/4 gab around the whole perimeter even by the door jams like the one u just cut?
@SupremeGrace18
8 жыл бұрын
Good idea to sand! Flawless look, thanks
@Macdeeeee
6 жыл бұрын
Great video, always wanted to know how to do this!
@DragonBiscuit
2 жыл бұрын
Perfect - exactly what I needed
@user-yp2ds8uu1u
6 жыл бұрын
You have to cut door gem or pillar before laying the under lay cover. because dust can get in to the under lay inside then you are in trouble after laying the floor.
@Kelly-lo6cz
4 жыл бұрын
Please help! I am doing the same thing as you and the it is not cutting the wood at all. It's a brand new tool. It's vibrating but not cutting... I'm putting slight pressure on it and it doesnt cut. What am I doing wrong?
@jamisonsdad1963
4 жыл бұрын
Your Blade may be dull or the wrong blade.....
@gregl2249
8 жыл бұрын
great job---what happens when the casing is deeper than the saw depth -----a different blade i assume
@KBem93
4 жыл бұрын
If its deeper, dont cut that deep. Cut it shallow and knock it out.
@jtyreetex
7 жыл бұрын
I have the bosch saw, but I was wondering about the trim? Doing a hallway and will be going in and out of hall closets. Do you take the trim off or just cut the door jam and then use 1/4 round to cover the gap between the laminate and the trim? Great video thanks for the advice. No plug here but I bought a used Bosch MX25E on Ebay for $38
@DonaldConrad
5 жыл бұрын
In the video, the baseboard is removed.
@father6371
4 жыл бұрын
Do you maintain the 1/4 inch expansion?
@chipjumper
6 жыл бұрын
Could you do this with door bottoms too?
@themermikkishow6710
6 жыл бұрын
This is brilliant! thanks so much!
@jessepuentes7021
2 жыл бұрын
Awesome video! Thanks!
@mistera4889
4 жыл бұрын
So it's okay to cut bottom door casin? Im obviously not a framer but im curious if this would pose any major structural issue, thanks for the vid👍
@jeffcampsall5435
Жыл бұрын
I have yet to find a multi tool blade that does anything. I’m better of keeping the tool off and sawing with it 😡 I end up using a backsaw.
@aboyd44
2 жыл бұрын
A+ video, thank you
@gargar8196
3 жыл бұрын
Good job 👍
@jjohnson8353
8 жыл бұрын
Great job. Thanks. I'm doing this tomorrow☺
@nigelhunter4230
3 жыл бұрын
Great Video. Thanks
@tedyBear59
4 жыл бұрын
Great work
@shelleyhuskey1870
4 жыл бұрын
Nice video, very helpful!
@YNLEXPOSURE
6 жыл бұрын
I did notice a small gap between flooring and door casing. For perfection you need to consider the cutting blade thickness and come up with a tool support thinner than your flooring by this amount. If it's an inexpensive rental it wouldn't matter.
@Archifx
6 жыл бұрын
Needs a small gap for expansion and contraction.
@majusavel
6 жыл бұрын
Can I do the same from the baseboard? I don't want to remove the original baseboard from my room.
@frbird51
6 жыл бұрын
I guess you could use the same technique for the baseboard but it would take quite a bit of time. We normally either pull the baseboard off and then reattach it once the flooring is down (which requires touch up work like caulking and painting) or just run the flooring close to the baseboard and then tack some shoe moulding or quarter round onto the lower part of the baseboard to hide the gap which requires less touch up work than pulling the baseboard and reattaching it.
@majusavel
6 жыл бұрын
frbird51 thank u. I did the quarter round & put it doesn't look neat but it's ok only small room.
@nelsonpeddle8972
7 жыл бұрын
Fantastic job and video! Subbed
@mchaelhron279
5 жыл бұрын
Ty Sir. I think I can do that!
@christen1075
3 жыл бұрын
Will use the utility knife trick if I can get it flush. Bosch for pros, and I too have a $20 Harbor Freight which is all you need for DIY'er. I think the blade is the most important choice, as I found out when I replaced a 10" 80 tooth Diablo blade with a new one. Cuts are like night and day. Can't overemphasize tossing you $50 blade and putting up a smoke screen of burned wood in the house or backyard. Never again will I make that mistake.
@alexbojsza734
Жыл бұрын
First saw so quite
@346barry
6 жыл бұрын
Great video
@adelsoaadi6657
5 жыл бұрын
What about on a metal door frame?
@michaelhucks2313
Жыл бұрын
People will say scribe and silicone, but really, with most floating floors, it voids manufacturers' warranties. This method restricts a floating floors ability to expand and retract. You're probably better off with a direct stick LVT if a house has steel door frames.
@pb03brar47
5 жыл бұрын
Good job..
@MyAccountBitch
8 жыл бұрын
thanks man
@sandysimpson194
7 жыл бұрын
Thanks for sharing.... Good Job...
@Archifx
7 жыл бұрын
+Sandy Simpson hands a bunch!
@yd6974
7 жыл бұрын
very helpful!!
@bibekadh8302
7 жыл бұрын
nice
@kieranmoore8894
4 жыл бұрын
Don't use a battery multi tool as it takes for ever.
@mikebetts2046
5 жыл бұрын
Seems to me it would be better to reduce the thickness of the scrap piece used as a guide first. Run it through a planer to reduce thickness equivalent to the kerf of the blade.
@GFSwinger1693
2 жыл бұрын
Music is distracting.
@Archifx
2 жыл бұрын
So is your comment
@AhrueIlustre
6 жыл бұрын
That was auto tuned
@leestewart155
4 жыл бұрын
llllliiikkkeee a glove
@charlesberlanga4452
5 жыл бұрын
The music is distracting and annoying
@Archifx
5 жыл бұрын
So is your comment. Very constructive. Thanks for the view.
Пікірлер: 95