Thanks so much. I was watching nothing happen until I watched your video and caught you bringing to my attention that I had cancelled the update by not hitting NO to cancelling the update. Worked like a charm.
@bknev
5 ай бұрын
Finally! Excellent tutorial video for a dummy! However, after loading the SD into my helix 7... Message said "invald" I waited for about 10-15 seconds, THEN, it loaded exactly as you showed in this video. Thank You soooo much
@aarchas
Жыл бұрын
Was sitting here staring at my unit wondering if it was loading the update in the background... found out I had aborted the update from your video.
@greghubble5122
2 жыл бұрын
Thank you for the simplicity and conciseness of your video.
@ericwilliamsfishing
4 жыл бұрын
Tried it 5 times before I found your video. Worked first try after I watched this!
@meeyou3128
3 жыл бұрын
Thank You, your video is much more helpful then Humminbird's video!
@TheWeekendAngler
3 жыл бұрын
Thank you! I really appreciate your taking the time to leave me a comment. I am glad it helped you out.
@royallison6427
4 жыл бұрын
I followed your directions and now have an updated fish finder. Thanks.
@TheWeekendAngler
3 жыл бұрын
It needs to be smaller than 32gb so that you can set the file format to fat32. A 1gb card would be more than plenty, but they're hard to find so use an 8gb or 16.
@grizzy7469
4 жыл бұрын
Thanks for all your help man. I have no clue what I’m doing and don’t understand the electrical side at all.
@brandon-tz6bu
Жыл бұрын
Thank you for telling us to not abort the install lol 😂 i came here because i did exactly that. Appreciate it man
@TheWeekendAngler
Жыл бұрын
It's easy to misread that menu. Humminbird really dropped the ball on that one. I'm glad it helped!
@brandon-tz6bu
Жыл бұрын
Definitely easy to do it wrong. I bet a ton of other people run into that too.
@dreamlookautodetailingauto3353
Жыл бұрын
Thanks for showing how to do this.
@nikolutkauskas5126
3 жыл бұрын
I have the card formatted fat32 and the update is the only thing on it. When I click update and confirm the update it will say “updating don’t interrupt” it then goes to the hummingbird screen that says software updating for about 2 seconds then the system turns off and reboots. Once it reboots it asks me if I want to update the unit over and over again in the same cycle. Any ideas?
@richardjohnson1471
3 жыл бұрын
Ever figure it out? Same problem
@nikolutkauskas5126
3 жыл бұрын
@@richardjohnson1471 no I’m really pissed off though. I can’t get ahold of humminbird they put me on hold for hours. If you figure out what it is please tell me and I will do the same for you.
@kennethmacdougall1084
3 жыл бұрын
Same problem
@richardjohnson1471
2 жыл бұрын
Had to send mine in. Waiting to get it back
@nikolutkauskas5126
2 жыл бұрын
@@richardjohnson1471 yup same here.
@stephenparker1428
4 жыл бұрын
Thanks. Now I understand how to do the update. Great help!
@kanaletumlinson
2 жыл бұрын
Thanks for the informative video! Need to update mine!
@Trag1cMag1c
Жыл бұрын
I was struggling. Realized that I had aborted the update twice. Some of the fish I catch are smarter than me. Thanks for pointing out the "abort" selection for me. Feeling dumb right now.
@TheWeekendAngler
Жыл бұрын
Don't feel dumb. I learned it the hard way.
@darrinbriggs318
8 ай бұрын
How do I know if my unit needs an update? Is there something to look up to tell me that it would be beneficial to do one? Thanks for a simple-to-understand video.
@fjin1
3 жыл бұрын
You need to format the 32GB SD card into FAT32 , NTFS will not work . You're welcome
@MrPALEHORSERIDER
3 жыл бұрын
Thanks you made it simple
@mschmidt3108
6 ай бұрын
Thanks!!!!!!
@mschmidt3108
6 ай бұрын
I learned a lesson last year. I bought the Ontario card and didn’t test it before going to Canada. My MN and WI cards worked fine. Canada card didn’t work. In preparation for my trip in May I bought a new Ontario card. Doesn’t work. I have never updated my software. There’s a note in the instructions clearly telling me my general software needs update and then I have to do an update to the base map. Working on that now. Hopefully I get everything accomplished and then I get to sell one gently used Ontario card!!
@ernie9819
4 жыл бұрын
Great informaation, Thanks
@HooknHaulfishing
2 жыл бұрын
Awesome ! Thanks so much
@shiroshowa7846
10 ай бұрын
my unit did not recognize the new software version no matter what I try. So I reload my software to 2.28, and still did not work. any help will be greatly appreciated
@TheWeekendAngler
9 ай бұрын
Occasionally, if a fishfinder unit loses its mind and refuses to update, it can be the result of corrupted firmware. In that instance, it's best to contact Humminbird support.
@PHATBASSASSASSIN
5 ай бұрын
I can’t get my unit to zoom with the plus or minus buttons. It’s a helix7 g2n
@fuzzyfultz
2 жыл бұрын
Awesome ! 01/01/1022
@monicamaz5038
Жыл бұрын
Hello I hope you can help me. I followed your instructions, I clicked No to abort, but it kicks me out, it shuts down like it wants to do the update but it rejects itand doesn't do the update, it takes me to the same prompt and I click NO to abort again. What could cause this and how do I fix it? I used the 32G SD card, downloaded the software, basically I followed the instructions to the T but it all goes well up to that screen where I have to select No to abort. Any help is appreciated.
@mikebartlett7728
Жыл бұрын
I have the helix 5 di and mine didn’t show no box on the screen like this one did
@PHATBASSASSASSIN
5 ай бұрын
I just started using old helix 7 g2n can we still update them ?
@TheWeekendAngler
5 ай бұрын
Yes, but I don't think they've released an update in quite some time.
@mattress2331
3 жыл бұрын
Great video Ty
@Zavala211
3 жыл бұрын
Thank you
@KarlSchoen
Жыл бұрын
I have a helix g4n 15 chirp with mega si + mega di+ chirp I can find the download for si or di Do I do both updates. I am two updates behind in what order
@crazylewiemike
4 жыл бұрын
Thanks For The Great Information
@user-rv3wh9rh8z
4 жыл бұрын
Updated mine successfully. What is the most noticeable corrections this newest update fixed?
@BrianRockFishing
Жыл бұрын
Hmm..I did the same thing with mine on my kayak but it did nothing when I plugged the card in. What give?
@grizzy7469
4 жыл бұрын
Where did you put your 15 amp fuse at? The helix 9 manual says to use a 4 amp fuse so if you use a 15 amp fuse how does that work? I’m sorry I don’t understand how it works. If I bought 10awg wire with the pvc white coating on it where would I put my fuse at?
@caskets100
Жыл бұрын
Good video
@TheWeekendAngler
Жыл бұрын
Thanks!
@jamessamoska7223
4 жыл бұрын
Perfect. Thanks!
@joepittiglio6954
Жыл бұрын
The software I’m trying to load is 2.3 on my Helix 7 gen3 . I’ve done what you are showing but the unit just sits there and is not recognizing the card when I insert it. The only difference is that im not in demo mode. Could that be the problem? It’s a 16gb card and the software is definitely on it .
@TheWeekendAngler
Жыл бұрын
It doesn't need to be in demo mode to work. Check to make sure the file is not in a folder on the card. That will mess it up when it happens
@royroth5310
4 жыл бұрын
GOOD INFO & VIDEO
@erics_TX_
3 жыл бұрын
Does the card spring out if you push it in? I can not get mine out of the unit at all. It only goes one way right? Thanks for the video, good stuff.
@TheWeekendAngler
3 жыл бұрын
When you push in on the card, it will pop out slightly, but not enough to get your fingers on it. I use the tip of a pocket knife to CAREFULLY pull it out far enough that I can grab it.
@walleyeheadztackle5415
3 жыл бұрын
I'm having problems the hummingbird will not recognize the sd card
@TheWeekendAngler
3 жыл бұрын
What size SD card are you using?
@walleyeheadztackle5415
3 жыл бұрын
@@TheWeekendAngler 32gb
@walleyeheadztackle5415
3 жыл бұрын
@@TheWeekendAngler I have the ice helix 7 g3n model
@TheWeekendAngler
3 жыл бұрын
32gb should recognize as long as it is still in fat32 file format. If it's partitioned as exfat, the Humminbird won't detect it.
@walleyeheadztackle5415
3 жыл бұрын
@@TheWeekendAngler I fiquered it out thanks
@JCASTELLUCCIOJR
Жыл бұрын
Is it necessary to save/download content on unit (way-points, routes, tracks) BEFORE DOING THE UPDATE??? THANK YOU IN ADVANCE...
@TheWeekendAngler
Жыл бұрын
It's not necessary, but it's not a bad idea. If things mess up you could have to do a factory reset
@grizzy7469
4 жыл бұрын
Nice video, thanks. How do you power your unit for at home/ in the garage? Basically not on your boat or out on the water.
@TheWeekendAngler
4 жыл бұрын
I do electronics repair on the side, so I have a couple of adjustable power supplies on my repair bench. I just hooked up an extra Humminbird power cord to the power supply.
@grizzy7469
4 жыл бұрын
Ok thanks. I am electronically illiterate. Do you have any advice on running a 4 amp fuse for the helix 9 on a Jon boat and then to the battery. There are no platform on the Jon boat so the wires will just be laying there. I honestly have no clue what I’m doing lol. I try to learn and watch videos on you tube and just get more confused.
@TheWeekendAngler
4 жыл бұрын
@@grizzy7469 4 amp fuse is probably a little small for the helix 9. I went with a 15amp on my helix 7 and ran 10ga marine wire straight to the battery. I connected my Humminbird power cord to the 10ga wire.
@juststatinfactssv4989
3 жыл бұрын
Thanks
@jeffpharr1653
3 ай бұрын
My hummingbird helix 7 is stuck on 0.6 feet
@Keepit10081
2 жыл бұрын
We're you soppse to reset to default first?
@TheWeekendAngler
2 жыл бұрын
There's no need to. Part of the update process resets it to default now. It does it for you.
@rjguess
3 жыл бұрын
What are those flat lines running at the top of your screen on the fish finder? Mine have that too. But my other unit just like it does not have those lines.
@TheWeekendAngler
3 жыл бұрын
It's in simulator mode in this video, but those lines at the top are surface clutter. Trash in the water or turbulence can make them appear. There is a setting for how much of it you want to see.
@rjguess
3 жыл бұрын
@@TheWeekendAngler ok. Good to know. Thanks for the info.
@mikemarinakis305
4 жыл бұрын
I followed directions to the t from hummingbird website and my unit got bricked
@mattress2331
3 жыл бұрын
How come the Navionics is C4 and does mapping but you need to have C10 to download Firmware? Thanks
@TheWeekendAngler
3 жыл бұрын
Navionics probably uses class 4 cards to save a couple of pennies per card. Their cards would perform better as class 10. As far as I know you can still use a class 4 card to download firmware if you wanted to, but since class 10 cards read and write faster, they're still the better choice.
@nicholas2932
3 жыл бұрын
that 16gig Navionics chart card... did you freely download the charts? the seller is taking his chart card with him and im trying to figure out how to put maps on it. (helix 5 gps)
@TheWeekendAngler
3 жыл бұрын
The charts will stay on the card. If he's taking his chart card with him, you'll have to purchase your own if you want to keep using navionics. For what it's worth, navionics usually puts their cards on deep discount around February of each year. That's usually when I buy or renew mine.
@trevorsweet6118
3 жыл бұрын
How would you update a G1 Helix 7DI there's no SD cards or slots
@TheWeekendAngler
3 жыл бұрын
It's probably going to require the Humminbird AS-PC3 cable to do it. Read the instructions at the link below: www.humminbird.com/support/faqs/NonCardReaderSoftwareUpdate
@bradjohnson6315
Жыл бұрын
Tried everything and when I load sad card unit says sd card successfully encrypted and nothing else.
@TheWeekendAngler
Жыл бұрын
Wow. That's a very strange error message to be seeing. I wish I had an answer for you, but in this particular case, you may need to contact Humminbird customer support
@bradjohnson6315
Жыл бұрын
Yea sir funny thing is helix 9 on front and 12 on rear reading same thing. They are both g4 with less than two years. Thanks for your help
@northeastkentuckyoutdoors6455
Жыл бұрын
Mine says same thing
@GmanfromTexas
3 жыл бұрын
I don't know how to see what version my Helix 7 g3 is running. I have gone through all the menus screens I can see
@TheWeekendAngler
3 жыл бұрын
When you first turn on your unit, press the MENU button for start up options. Using your cursor button, scroll down to where it says SYSTEM STATUS and press the right cursor. This will bring up a screen showing your unit's information. Look for Software Version about halfway down the screen.
@GmanfromTexas
3 жыл бұрын
@@TheWeekendAngler got it. Worked. Thanks brother
@TheWeekendAngler
3 жыл бұрын
@@GmanfromTexas glad you got it, brother.
@Lray4x4
3 жыл бұрын
does the unit have to be put in demo mode for this to work? My helix 7 and 5 both won't do anything when I put the card with the updates in.
@TheWeekendAngler
3 жыл бұрын
No. Just turn on the unit as you normally would. Make sure the update file isn't in a folder on the card and that the card is in fat32 file format. If you download the update file from Humminbird in zip format, you'll need to extract it before putting it onto the SD card
@Lray4x4
3 жыл бұрын
@@TheWeekendAngler How do I tell what I downloaded it as?
@TheWeekendAngler
3 жыл бұрын
@@Lray4x4 if you right click on the file and hit properties it should tell you. You're wanting a BIN file type.
@Lray4x4
3 жыл бұрын
@@TheWeekendAngler They are bin files
@TheWeekendAngler
3 жыл бұрын
@@Lray4x4 ok. That's what you want. Make sure the file is in the root folder of the SD card. That means when you open the card in file explorer you see the file and not a file folder.
@johnnyhelems5296
2 жыл бұрын
Is not working on mine
@keithwelnicke4042
3 жыл бұрын
Anyone know why when I download the updates it comes in as a pdf file?
@TheWeekendAngler
3 жыл бұрын
That's very strange. It should be a bin file. What model are you trying to update?
@keithwelnicke4042
3 жыл бұрын
@@TheWeekendAngler helix 7 si gps
@gailkohler9583
4 жыл бұрын
Didn’t lose my sad card I lost the card slot cover ☹️
@TheWeekendAngler
3 жыл бұрын
Yeah I really wish they'd attach it with a tether.
@erics_TX_
3 жыл бұрын
@@TheWeekendAngler that would be a great idea actually.
@patrickrede
Жыл бұрын
This needs to be played in all evangelical fake Christian churches.
@TheWeekendAngler
Жыл бұрын
OK. I'll bite... Why?
@mikewolfzorn7128
Жыл бұрын
Far from easy
@TheWeekendAngler
Жыл бұрын
Can't make it much simpler. I suppose I could draw a picture in crayon for ya.
@mikewolfzorn7128
Жыл бұрын
I still haven’t conquered it. Won’t download too my chip
Пікірлер: 123