i have no idea what you are talking about,, or trying to teach !! however ,, because I like your video's THUMBS UP !!
@TexasBarndominiums
4 жыл бұрын
😂 Thank you
@jamesogorman3287
4 жыл бұрын
They’re like Reeves Drive pulleys. My wood lathe has basically the same thing. I can certainly see the advantage for the power trowel.
@Psy6o
Жыл бұрын
Good explanation for a subject that is so technical
@garrettmccarty2642
4 жыл бұрын
I was just watching the episode where you mentioned this lol. I’m wanting to do this on my machines and the custom machine I’m currently starting on.
@markrobles4267
4 жыл бұрын
Heck yea Eric, i was on your live stream and wanted to ask you about this modification, but i got on late and got to ask you only one question. Thanks for the info, looking up parts on your links right now
@joehosie
4 жыл бұрын
Wow Erik! Great video yet again!
@TexasBarndominiums
4 жыл бұрын
Thank you.
@rperez3883
4 жыл бұрын
New drinking game. Drink every time he says "however".
@jrconcrete4503
4 жыл бұрын
Thank you Eric 👍🏼
@nickreich6841
3 жыл бұрын
You should try a Boren trowel, they spin a lot faster the all others and it would be nice to have you review one.
@chazgeisler6213
4 жыл бұрын
Where did you get your belt from? Also what size belt did you end up using for this whiteman 36”? I have the same power trowel I am wanting to do this conversion on.
@eduardososarubio3051
4 жыл бұрын
Great video. I didn’t see the connection for the pro skyhook. You should have had Manny pre order it from amazon. Lol.
@abv2518
18 күн бұрын
Can you do the 46 inch trowel Need a parts list thanks
@finnlife1245
Ай бұрын
Set this up on a power trowel with a one inch driver and 3/4 driven and when I went to spin a pan the belt kept getting stuck just wondering am I running the wrong size belt to long or too wide?
@anthonyhernandez2396
4 жыл бұрын
Hey eric cvt clutch came in today buy my shafts are not long enough to go all the way in the cvt clutch
@mattallain8431
4 жыл бұрын
But however... i liked the explanation! 😎👍🏻🙌
@derekmeerdink9725
Жыл бұрын
Hi Eric. Great video. Where do you find cvt clutch kit?
@alejandrocontrerasacuna2580
4 жыл бұрын
Great video !
@alejandrocontrerasacuna2580
4 жыл бұрын
Going to try it out my self hopefully everything turns out okai lol
@TexasBarndominiums
4 жыл бұрын
36” machines don’t really need it. It’s an awesome upgrade on 48” machines though. Use Comet 40 series for those.
@alejandrocontrerasacuna2580
4 жыл бұрын
Will do thanks
@dukhtr3
4 жыл бұрын
Well I found out that my Allen power trowels lower shaft is hardened steel. I guess I will try my whiteman or mbw trowels. Have u ever ran into hardened shafts before? These are all 48" trowels with 8-9 hp motors
@juanllamas1486
Жыл бұрын
Hi do you happen to know what I need to do to move my motor over towards the pulley about a inch out of line?
@benjaminperez986
3 жыл бұрын
I'm in the process of converting my machine and I'm having trouble drilling the shaft. I believe the one I have is in fact harden steel. What do you recommend?
@anthonyhernandez2396
3 жыл бұрын
Eric im trying to do a cvt upgrade on a older superior trowel machine but these bits are not drilling in to it is there a special kind of drill bit ...also when can you make a video on how to balance a whiteman trowel machine
@caseyjohnson6573
3 жыл бұрын
I was wondering if you can tell what cvt clutch for a 36" walk behind trowel? Please
@tommytommy9490
4 жыл бұрын
I have a question I seen your clutch swap on your 3 footer which was amazing next question have you ever put a Predator motor from Harbor Freight on your Whiteman trowel machine.
@TexasBarndominiums
4 жыл бұрын
Yes.
@pedrocaballero1497
4 жыл бұрын
That conversion you did will not work. You didn't put in the brass magnets. This will totally mess up the beam stretching ability of that machine. It is now basically a huge paperweight. Great video. 😎 👍👍👍👍👍
@charlydjr
4 жыл бұрын
Can you make a video on how to change the oil on it
@TexasBarndominiums
4 жыл бұрын
Sure, but it’s super easy. Remove bolt at bottom of engine, usually in the front or back. Drain oil and replace screw. Fill up until oil runs out of port where you check it. Make sure engine is flat when you fill back up.
@bluelaser4534
4 жыл бұрын
@@TexasBarndominiums wat kind of oil do u use?
@caseyjohnson6573
3 жыл бұрын
I'm wondering if you can do this to a 36" walk behind
@anthonyhernandez2396
3 жыл бұрын
I end up welding a nut coupling to theshaft
@cntslesfabrication
4 жыл бұрын
Erik how do I go about flatting and concrete walkway that was just poured 2 weeks and it's not flat at all and the walkway was put in so my elderly mother is able to walk in and out of the house without getting tripped for safety?
@TexasBarndominiums
4 жыл бұрын
Grinder or micro topping.
@anthonyhernandez2396
4 жыл бұрын
Finally did mine it works good only problem is it started riping my belt when the cluctch opens up ....i do have a 1 inch belt intead of a 5/8 s 5 /8ths supposed to be the original one wonder if that could be the problem
@gustavocastaneda8458
2 жыл бұрын
Did you get it fixed ?
@juandunas2381
2 жыл бұрын
Hi great video ,,, did you know that kind of belt does i need for a trowel with original centrifugal clutch?
@derekmeerdink9725
Жыл бұрын
A-26 original belt on 5.5h machine (36”)
@juandunas2381
Жыл бұрын
Thank you have a blessed day
@derekmeerdink9725
Жыл бұрын
Hi Juan. Did you try cvt clutch at all?
@juandunas2381
Жыл бұрын
No I was just replacing the original belt
@kriswantosantoso8901
4 жыл бұрын
Would be better if the video is zoom in and out, so can see clearly what you are working on.
@tommytommy9490
3 жыл бұрын
Ever have trouble with your gearboxes after switching them over to CVT system
Пікірлер: 57