Man I've been working Construction since I was 15 and 21 now didnt know how to use a stud finder till now😅😅, thanks brotha🤙🏽
@robsgaragewoodworkin
3 жыл бұрын
You're Welcome!
@user-dq9rr9mv3f
3 жыл бұрын
Omg thank you! This lady learned a lot today.. I had no idea why it was red on the tape measure.. and shhh hubby didn’t either..
@robsgaragewoodworkin
3 жыл бұрын
LOL! My lips are sealed!
@yungrod3d895
3 жыл бұрын
This Helped Me Out A lot! Even Saved Money 💰 [THANKS]
@robsgaragewoodworkin
3 жыл бұрын
You're welcome! Thanks for the comment! Cheers! Rob
@1dandy49
2 жыл бұрын
Great video Rob. I must own 5 stud sensors from zircon to black and decker. This model you used in your demonstration, I've found to be the best and most accurate. Great tips too. Thanks for sharing.
@robsgaragewoodworkin
2 жыл бұрын
I don't know why, but it's better than all the rest. Thanks for your comment! Cheers! Rob
@aot9339
2 жыл бұрын
This is very useful, especially the various cases in which the sensor may not work properly.
@robsgaragewoodworkin
2 жыл бұрын
Thanks for your comment! Cheers! Rob
@ju66er1
3 жыл бұрын
Something you should point out is that the stud sensor uses the drywall screws to register. The stud detector has a magnet inside and lights up when it detects metal in close proximity not wood
@robsgaragewoodworkin
3 жыл бұрын
The Zircon stud sensor is an electronic stud sensor that locates studs by scanning fluctuations in wall density. www.studlocator.com/magnetic-vs-electronic/
@jya-butterfly
Жыл бұрын
You are nice and reassuring. Thank you.
@anacampos974
Жыл бұрын
Adonde puedo ir aprender acerca de cómo hacer pequeños trabajos
@jazzblakk69
3 жыл бұрын
Thank you Buddy
@robsgaragewoodworkin
3 жыл бұрын
You're Welcome! Cheers! Rob
@drexq_477
3 жыл бұрын
Good video
@drexq_477
3 жыл бұрын
@@robsgaragewoodworkin good video
@christinew8328
2 жыл бұрын
Awesome vid...VERY informative. THANK YOU THANK YOU THANK YOU...😘🥰👌
@robsgaragewoodworkin
2 жыл бұрын
You are so welcome!
@abbeyyoung1404
3 жыл бұрын
I have this type of stud sensor. How do I calibrate it?
@robsgaragewoodworkin
3 жыл бұрын
You don't actually calibrate it. Place it against the wall, press and hold the button and gently slide it slowly across the wall until the light hits the top peak. That is the edge of the stud. They are 1.5" wide. You can repeat the procedure going the opposite way to verify the other edge of the stud. If you are having difficulty getting a good reading you may need a new battery or maybe the wall is plaster and lathe. Plaster walls have wood lathe everywhere which screws up the stud finder readings. Good Luck! Cheers! Rob
@abbeyyoung1404
3 жыл бұрын
@@robsgaragewoodworkin thank you!
@mikegee5205
3 жыл бұрын
Can you use this on ceiling??
@robsgaragewoodworkin
3 жыл бұрын
Yes but if you have a popcorn ceiling it might be more difficult. Good Luck! Cheers! Rob
Пікірлер: 29