Thank you so much for the clear instructions - I've been bashing my head against a wall trying to figure out how to use some ICSP headers on a PCB I'd built to flash a chip. With this instruction, I was finally able to.
@techathome
7 ай бұрын
Welcome!!
@easy_3d
4 ай бұрын
Hey deepak, how do we upload code to arduino with bash ide?
@duviday
Ай бұрын
"as you can see the led on our target board has started blinking" bruh it was always blinking.
@beaconing7689
Ай бұрын
ughh.. clean dat shit
@techathome
Ай бұрын
👍
@mohdalriyami3531
10 ай бұрын
so, if I have a board that isn't working properly then programmed using the ISP, can I use it independently without the programmer board?, (like doing reset to the damaged arduino)
@techathome
10 ай бұрын
Yes u can use independently without development board.
@TheZerocul
Жыл бұрын
Tell me what firmware to flash matekH743 or matekH743bdh to work dhot? is there any difference? Dshot on firmware will work matekH743?
@mohitsingh5665
3 ай бұрын
Thanks
@techathome
3 ай бұрын
Welcome
@25sampodtechzone
4 ай бұрын
Can I use this isp for unbrick Android using easyjtag software?
@techathome
4 ай бұрын
I don't have idea on this. But the Arduino behaves as standard isp programmer.
@nigelwillis1573
4 ай бұрын
Thanks for this. There is a lot out there about ICSPs, but very little that is so concise and delivered in such a practical, easy to follow way.
@techathome
4 ай бұрын
Welcome!!♥
@kiercariaga9565
3 ай бұрын
Help, I have an arduino board that isn't working. I'm not sure if it fried itself. What happened is that I tried to test a servo motor with a sample code on the arduino software, plug out the usb cable then plug in the 12v barrel jack, then the burnt smell came out of nowhere.
@techathome
3 ай бұрын
I have used 9v battery on round DC jack. It works fine. But never connected to 12v on this connector. Check the specifications. Actual microcontroller chip might be still fine. Only power regulator might be burnt. Check on USB once.
@vilassanap4853
5 ай бұрын
Can u suggest sir, how to program sdi controller with aurduino?
@techathome
5 ай бұрын
Can you share the board link, I have not come across it?
@skd69
3 ай бұрын
can you help me program the Atmega16u2 chip please
@techathome
3 ай бұрын
I hope you have sent mail
@logesh737
6 ай бұрын
Useful content
@techathome
6 ай бұрын
Thank you
@prestononuselogu9973
4 ай бұрын
Thanks!
@techathome
4 ай бұрын
Welcome
@qwlol
9 ай бұрын
Very helpful. Thanks!
@techathome
9 ай бұрын
Welcome
@haydarkamil9702
10 ай бұрын
i have a nano from china. Arduino as isp doesnt work. Getting Invalid device signature error u have any tutorial?
@techathome
10 ай бұрын
Sorry, I have no idea on this. While checking on internet some people say there might be issue with oscillator(target chip's clock not running)
@Hrudayesh
6 ай бұрын
Hello bro...I tried using arduino as ISP to blink led for 1.5 sec. The code was uploaded to target. But the programmer arduino board is also blinking for 1.5 sec. Is it normal??
@techathome
6 ай бұрын
Actually the programmer board will be having ISP code. It will have same code even if you use it for flashing the target I have not observed the LED properly. May be it is not blinking because of blinking code. Try to upload blink code with different delay time to the target and see.
@Hrudayesh
6 ай бұрын
@@techathome Thanks a lot bro. I will try
@E-4-elecTronic
5 ай бұрын
Failed chip erase upload error exit status 1
@E-4-elecTronic
5 ай бұрын
What should i do i am facing this problem when i am burning bootloader
@Hrudayesh
5 ай бұрын
@@E-4-elecTronic Maybe its the issue with bootloader. Try burning the bootloader from arduino IDE. It might resolve this issue I guess
@aaroncharles9203
Жыл бұрын
Op bro
@techathome
Жыл бұрын
Thank you
@mrknight3552
Жыл бұрын
🔥
@techathome
Жыл бұрын
Thanks
@chakraprasad8110
Жыл бұрын
Icsp in sir cute 😂
@tb303wpf1
3 ай бұрын
Great video my friend! Thank you for the detailed information. 👍😁
Пікірлер