Thanks for sharing the way to stabilize the value.
@iopop7985
3 жыл бұрын
well explained and funny "ups - tu much current".... :))
@RixtronixLAB
Жыл бұрын
Good info, well done, thanks for sharing it with us :)
@dejangambin9160
Жыл бұрын
Hi. Where does 13.51 (for 5A sensor) come from?
@jjawads88
3 жыл бұрын
thanks for such a simple and easy code
@yaaro713
4 ай бұрын
Very nice explanation, the purpose of the video, the code, the connections were all explained well!! Thank you!! 😊 But the only thing not understood was why 13.51A?
@AshiqurRahman
2 жыл бұрын
What is maximum limit of voltage of the end points where the sensor is connected ?
@ShilpaGireesh
5 ай бұрын
Hi, Could you recommend the above sensor for measuring a current less than 0.9mA from a board? My project is based on Arduino.
@emadalrwishdi7820
Жыл бұрын
you are the best
@matthewaertke865
3 жыл бұрын
I have followed this schematic and layout for the device, but can't seem to get an accurate reading on the current. I have the 20amp acs712 sensor, with ip+ hooked up to +5v power supply, and ip- hooked to the 5V supply on a part i am trying to measure current on, then ground and 5v from the arduino to the acs712 and A0 is the Vout of the acs712. Am I doing anything wrong, because when I power it with a curve tracer I read 12mA at 5v for the part, but the current sensor (with the code for the 20amp) outputs a value of ~72.1, and this has absolutely no correlation with what I am getting on the curve tracer. Please help!!
@t.n.1056
3 жыл бұрын
Explained absolutely well. Thanks.
@samhsavdr9647
4 жыл бұрын
Can you make diy 4s 18650 charging circuit for irobot vacuum cleaner? believe it would be great rating rating ceiling
@naz8885
7 ай бұрын
I want to create a system where an led turns on when my wireless charger is in use. I assume the load in this case would be the charger. How do I decide which amp to do with is a get a 10watt charger? This is a hobby project and I’m completely new to electronics. Thanks in advance!
@Rowan_
4 жыл бұрын
Could i get some explaining about the code, it works perfect btw.... thank u very much x
@justinyvesricablanca5734
Жыл бұрын
Hello, Sir good day! Is it possible to add a gsm arduino shield in the circuit? I want to ma a Open Cicuit Alert System. Basically, I intend to make an alert system that sends a text message if the current ammeter detects 0 current. Is that possible?
@user-wb1nl1ol9q
2 жыл бұрын
How can I write the current value on the LCD screen?
@aakashvishwakarma2496
6 ай бұрын
Hi,I am working on a project in which I use ACS712_30A with esp32 but its not working fine (It can't calibrate right power) can You help me with some solution.
@n1kkri
3 жыл бұрын
I am looking for a simple project using a 5MA/5A current sensor to sense my doorbell current when someone pushes my doorbell button. One of the transformer wires of my doorbell would run through the sensor. Sensor gets connected to a ESP32 DEV board which sends me a alert message.
@zakwanarrasyid5679
2 жыл бұрын
hi, why i try using this code the value of current is so high? i am using 20 A Acs 712
@abinayasri8427
6 ай бұрын
Same for me.. How did u rectify it?
@TheRainHarvester
3 ай бұрын
The min resultin resolution it can report is 20A / 1024 = .020 A = 20 mA
@Gallardo6669
Жыл бұрын
I have a big rpm autometer lying around. I would like to hang it at the wall and watch the needle dancing once my amplifier sucks amps to produce a bass.... Would you like to make a video about such a project???
@konainhaider2397
5 жыл бұрын
After long time you are here bro Why? Make early video
@rocky3004
3 жыл бұрын
We can check three phase motor amp 415 volt or 15 amp which sensor used
@raviprataptripathi4714
3 жыл бұрын
hello sir.... i am using hall sensor to measure armature current of pwm drived dc motor...but i am getting a pulses of current but i have requirement of analog value...how to fix this problem?
@reymarkpaculanan3297
2 жыл бұрын
i keep getting 18.77 amps even i don't connect the source in the module
@nandinikose1414
3 жыл бұрын
Code file is not support to app
@mikeberger1688
2 жыл бұрын
Bought one of these and the output goes lower than the 2.5v idle when current is detected? (Mine does). Thought it would have added to the output -- guess not. Confirm anyone?
@markangeloimporta1614
Жыл бұрын
Can i use that sensor to measure 200mA current?
@samuellutaama3667
29 күн бұрын
Was getting very unstable values,lwt me try this and see
@konainhaider2397
5 жыл бұрын
Plz make voice control home apliance
@allaboutall6071
3 жыл бұрын
Will this code work for AC Current or just DC current
@Aatikslab
3 жыл бұрын
Only for DC
@allaboutall6071
3 жыл бұрын
@@Aatikslab Could you please share the code for AC current
@emperoreyeanime4142
3 жыл бұрын
can acs712 measure voltage and current?
@DevSky
3 жыл бұрын
#DevSky good 👍.
@satirthapaulshyam7769
3 жыл бұрын
Hey how to measure ac current
@sherazkhan2939
4 жыл бұрын
Hi, Can I check AC current with it instead of DC?
@mugumegilbert4333
2 жыл бұрын
this beatiful
@prasana4047
4 жыл бұрын
LETS GET STARTED
@htpcandroid4903
4 жыл бұрын
innovate... don't imitate
@shubhamk2173
4 жыл бұрын
Where do u make circuit design
@Aatikslab
4 жыл бұрын
its in the description
@ersyaaugistin2336
4 жыл бұрын
Hallo sir, is the sensor can use for nodemcu esp32? Thx
@Aatikslab
4 жыл бұрын
Yes of course !!!
@ersyaaugistin2336
4 жыл бұрын
@@Aatikslab i'm so confuse why my acs show the wrong calculation about the current, when i tried to measure the current from a lamp, do you know what the trouble from? because i ever move from one pin to another but the measure still wrong. thx
@dipanshuyadav3723
7 ай бұрын
@@ersyaaugistin2336did you get solution because i am struggling with same thing now
@Sabhail_ar_Alba
19 күн бұрын
There's basically no coding required for this device.
@electrotech5748
4 жыл бұрын
How we can use it to measure AC current
@satirthapaulshyam7769
3 жыл бұрын
Same man. Have you got any solution?
@bittukumarthakur1429
5 жыл бұрын
Make nrf24 controller and receiver for drone and rc plane
@jameelsheik
2 жыл бұрын
Can you write code to make an overcurrent protection? The digital output pin of the Arduino should go high if the AC current value is crossed the predetermined value. I want to make a cheap overcurrent protection circuit for my AC Motor. When a motor is turned ON, it takes around 16Amps starting current for around 5 sec & 6 amps current in normal operation. I will use a CT if required.
@maheshvenk
4 жыл бұрын
Thank You. Can I connect two sensors to the aurdino board shown in the video. I am a layman.
@Aatikslab
4 жыл бұрын
yes you can connect upto 8 sensors to arduino`s analog pins ranging from A0 to A7
Пікірлер: 57