I haven't been able to get the NEO 6M to connect to satellites and blink repeatedly. Should I test in a different location, drive around in my car with it on or something different?
@paprighosh6063
Жыл бұрын
In the arduino idle tools section = From where the processes come, it not showing in my idle. Sir please please tell
@youssefcheerdi6241
2 жыл бұрын
I contacted neo6m at esp8266 but the neo6m led does not light up
@prernagokhale8719
2 жыл бұрын
Hey , I have done the connections same .But it it showing that check wiring in serial monitor and also LED is not blinking .Can u please help?
@warrenscorner
2 жыл бұрын
Very good Ahmad! Did I hear that right? It takes 6 to 7 hours to get a signal?
@AhmadLogs
2 жыл бұрын
yes right. it some times takes
@tanjiro3285
Жыл бұрын
@@AhmadLogs have u faced tried it (6 to 7 hrs ???)
@AhmadLogs
Жыл бұрын
@@tanjiro3285 just 2 minutes
@sunsethorizonstudios
Жыл бұрын
@@tanjiro3285some times you have to like put the GPS at some places at your room to get a good single or you can just put it outside your balcony
@avinashrajedits2217
7 ай бұрын
@@AhmadLogs Can I charge the GPS in 3.3V for 6 to 7 hrs at night time when I'm sleeping?? another question sir if we mistakenly connect it to 5V for 2secs and remove it does this make any issue for the newly bought gpsneo 6m
@ais_robotic
3 ай бұрын
make a gps fllow car
@islemhl2659
Жыл бұрын
hello i need a help , i have this module and i'm having some problems , this module takes a lot of time (30-45minut) to connect to the signal , even i connected correctly and put it on the outdoor
@AhmadLogs
Жыл бұрын
1. Try another gps module to see if the same issue with the new module. 2. I think your modules battery is down. you just replace a little battery on the module
@islemhl2659
Жыл бұрын
@@AhmadLogs But I bought it a month ago, how can the battery be drained so quickly? when I upload the full code for my final year project (accident vehicle), the module is providing incorrect latitude and longitude values (0.00, 0.00). However, when I upload a simple code just for the module (test GPS), it gives the correct position. why?? BTW the code is completly correct
@AhmadLogs
Жыл бұрын
@@islemhl2659 I think there might be weak satellite signals in your area. try to replace the antenna. or just give it a try with the new one.
@user-hv8yq1bt1t
Жыл бұрын
How can we extract the latitude and longitude information *only* and print it on the screen without other info?
@jumbo999614
7 ай бұрын
Open example from the TinyGPS library called "BasicExample". I found out that your code need following lines: TinyGPSPlus gps;
@hercaici
10 ай бұрын
Hi dear Ahmad.. Thank you for the video...I need your help..Why I can not see $GPRMC.. Why I see $GNRMC..?? I see the list when I open the serial monitor...But can not see $GPRMC and also GPGLL ...big problem...Can not analysis the numbers
@farhansabir0499
6 ай бұрын
My GPS light is blinking when I connect it with Arduino in computer but when I connect the antenna GPS doesn't work, what can I do?
@tanimashraf
4 ай бұрын
Special thanks for the tip about changing gps baud rate.
Hello, I ask you, I have a NeoGps module, I connect it to 5v but the LED does not turn on, do I have to wait up to 8 hours until it can turn on?
@AhmadLogs
Жыл бұрын
If you have just received the NeoGPS module, it should not take 8 hours for the LED to turn on. In most cases, it only takes a few minutes for the module to start functioning after being connected to a power source. However, if the module has been unused for a long time, the small battery on the module may need time to charge before it can connect properly. Make sure to double-check your wiring and power supply to ensure they are correct and stable. If the LED still does not turn on after a reasonable amount of time, you may need to troubleshoot the module or consider replacing it. Additionally, you may want to consult the documentation or contact the manufacturer for further assistance.
@tanjiro3285
Жыл бұрын
im not getting gps lock after keeping the module powered on for mare than an hour
@AhmadLogs
Жыл бұрын
try to change the location. try it on roof top
@TARUN__46
2 жыл бұрын
I hav connect as the circuit diagram but the gps module in not on not getting any light
@AhmadLogs
2 жыл бұрын
wait for two to three hours
@rohitrao9302
2 жыл бұрын
Hey my NEO6M is blinking but not printing anything in the serial monitor? How long do I have to wait until I get NMEA sentences?
@AhmadLogs
2 жыл бұрын
if it is blinking then it mean, the module is receiving satellite signal properly and working fine. Please check your rx and tx connection and baud rate
@賴楷傑-l1v
2 жыл бұрын
How to solve the problem that gps cannot locate indoors
@AhmadLogs
2 жыл бұрын
after connecting to the satellite you can take it indoor and it work like a charm.
@rayd6416
Жыл бұрын
Do you have a tutorial on command to reduce the data set through Arduino? I am looking for RMC and GGA data only.
@AhmadLogs
Жыл бұрын
unfortunately not
@sridharreddy9742
2 жыл бұрын
hi ahmed for my module the green light is not blnking what to do?
@AhmadLogs
2 жыл бұрын
have you attached the antenna? put it on the roof top and wait
@holywoodmania
Жыл бұрын
brother how much hieght required???
@AhmadLogs
Жыл бұрын
no height required. you can test if outdoor
@dadapeer4940
Жыл бұрын
No GPS detected: check wiring what can do sir please help me
@AhmadLogs
Жыл бұрын
If you're seeing the error message "No GPS detected: check wiring" when using a NEO-6M GPS module, it's possible that the wiring between the module and your device is incorrect. Double-check that the module is connected to the correct pins on your device, and make sure that the connections are secure. You may also want to verify that you're using the correct baud rate for your module. If you've checked all of these things and are still having issues, it's possible that the module or your device may be defective.
@dadapeer4940
Жыл бұрын
@@AhmadLogs Thank you sir.
@NoOne-br7bl
Жыл бұрын
where is the code?
@chbhaskar6413
Жыл бұрын
Can i use the same code for esp also
@AhmadLogs
Жыл бұрын
yes
@buddhichinthanaranasinghe1279
Жыл бұрын
Thank you so much sir ❤️ It's a really good explanation😎 Love from Sri Lanka🇱🇰
@AhmadLogs
Жыл бұрын
welcome
@moinshaikh6684
2 жыл бұрын
Mere bhai, ek alag se playlist create kar de, gps tutorials ke liye, pata nai kya kya batana padenga
@AhmadLogs
2 жыл бұрын
ok
@paprighosh6063
Жыл бұрын
Dada when i use gps on the roof with the laptop it is working properly. After setup led on the gps blinking after that when I use it in room the value is not giving properly. Dada pls pls tell, i am in trouble pls help me
@AhmadLogs
Жыл бұрын
try to change the location in the room
@paprighosh6063
Жыл бұрын
Is it necessary that every time we need to do setup?
@AhmadLogs
Жыл бұрын
@@paprighosh6063 It does not required to setup again and again. its simply means that your gps module is not receiving GPS signals from the satellite indoor. To improve the GPS signal strength indoors, you can try the following: 1. Move closer to a window or go outside: GPS signals can penetrate glass, so being near a window may help improve the signal strength. If possible, step outside to get a clear view of the sky. 2. Use High quality GPS Antenna. This can help improve the signal strength and accuracy of the GPS device. 3. Ensure your device is charged: A weak battery can sometimes affect the performance of a GPS device.
@paprighosh6063
Жыл бұрын
When i use it outside the house it's work properly get the value of latitude and longitude with in a minute. After that when I use it inside room it take time to get the value.
@AhmadLogs
Жыл бұрын
@@paprighosh6063 its normal
@ais_robotic
Жыл бұрын
Thank u so much vai
@AhmadLogs
Жыл бұрын
Always welcome
@shakerileiwat4341
2 жыл бұрын
Grear video Tank you
@AhmadLogs
2 жыл бұрын
thanks
@yogeshitaliya473
2 жыл бұрын
😍😍😍
@leonardocantillo62
2 жыл бұрын
Hello, I really like your channel. I have a question, is it possible through the sim800l to control a relay through commands given to a web server (php)? . Thank you very much
@AhmadLogs
2 жыл бұрын
yes it is possible. but It will not be reliable system due to the slow internet of the sim800l
@leonardocantillo62
2 жыл бұрын
@@AhmadLogs which comands i need to control a relay with arduino and php server? (with sim800l)
@AhmadLogs
2 жыл бұрын
@@leonardocantillo62 it is not as simple. you need to connect to the internet using sim800l. then you need to receive the data using sim800l. you also need to setup your PHP web server with MySQL server. you will also have to write the php script for send request from the server to your project. there are lot of more things you must consider.
@aniszed3641
2 жыл бұрын
thank you
@AhmadLogs
2 жыл бұрын
You're welcome
@rampage_xdit
2 жыл бұрын
Nice
@AhmadLogs
2 жыл бұрын
Thanks
@mehmet83edu
2 жыл бұрын
Hello sir . I want to make a rc bot controlled from the phone google maps. I want it to go to the points I set on the map. I couldn't do what I did. I look at your page every day to see if you have shared new videos. :) You give the best explanation and details I've seen. your every project is very instructive. You are a really good teacher. I wish you success. I trust you. please help.
@AhmadLogs
2 жыл бұрын
Many many thanks your appreciation. you idea is very interesting. I never think about it. its great. but I think this project is not as simple. I think you need AI (artificial intelligence) for this project.
@joydipraj6210
Жыл бұрын
Nano 6m led is not blinking what should I do
@AhmadLogs
Жыл бұрын
test it outdoor, replace gps antenna,
@saisahana4362
2 жыл бұрын
Heyy can you please say how to connect the antenna to the module board ?
@ShauwneMiguelSalientes
Жыл бұрын
Thank you so much for this video. I would love to know your codes for this and because of my curiosity and appreciation I would like to try this myself
@AhmadLogs
Жыл бұрын
you might check my github account for more codes. github.com/ahmadlogs
Пікірлер: 81