Great video. You are the reason I started scrolling over 20 years ago. Bought a cheap harbor freight Scrollsaw, ordered some spiral blades, followed your videos and never looked back. Now, just doing it better with the Pegas saw that I bought from you. Oh, and you can teach an old dog new tricks. I have never enjoyed cutting the tiny pieces as you demonstrated on this video. Come to find out I have been starting from the outside and going in causing cracking and breakage. Cool tip, starting from the inside and cutting out. You the man, Scroll On. 👍
@CharlesDearingScroller
2 жыл бұрын
Thank you so much Tom!
@keithdorn8142
Жыл бұрын
Great video, but where do you get a 5 inch pin end spiral blade? I can't seem to find them. One person even told me they don't make them with pin ends.
@casper1240
Жыл бұрын
Theres a world of difference with a cheap Scroll saw versus a more expensive one if only for blade changing just bought the Axminster Pro Scroll sa with Pegas blade holders excellent
@CharlesDearingScroller
Жыл бұрын
@@keithdorn8142 I can't believe I never saw this comment. My apologies. I'm afraid they don't make pinned end spirals
@lloydbannister8062
4 ай бұрын
Charles you my friend are an awesome scroller I tried the spiral blade and I like using them I just can keep on the line I don’t no if I titan the blade to much or not tite enough thanks for the great videos
@rayscrafield2106
8 ай бұрын
Thanks Charles, I've stayed away from spiral blades up until now. Your video has given me the basics. Now it's just about practice.
@CharlesDearingScroller
8 ай бұрын
There ya go! They seem intimidating but some day you'll look back and wonder why you waited so long
@RobinsBuysandDIYs
2 жыл бұрын
Hi Charles! Thanks for explaining all the different cuts you can do with spiral blades. Very helpful!
@CharlesDearingScroller
2 жыл бұрын
Glad it was helpful!
@stans6582
14 күн бұрын
EXCELLENT LESSON.........THANK YOU
@MartyRaaymakers
Жыл бұрын
Came back and watched this again. Ready to start using spiral blades tomorrow.
@dennisg11348
Жыл бұрын
Thank you Charles. I might finally get around to using spirals. Very good explanation and presentation.
@CharlesDearingScroller
Жыл бұрын
Thank you very much
@SimplyUnreal99
2 жыл бұрын
Great video Charles! You explained spiral blades very well!
@CharlesDearingScroller
2 жыл бұрын
Thank you sir
@herculesmyburgh5401
Жыл бұрын
Thank you it was helpful for me. I would like to see your clips to improve my scrolling.
@johnhuggins5021
Жыл бұрын
Thank you Charles for making this video. I have only been scroll sawing for the last 7 yrs or so and yet I still learned something new that would help from being frustrated while cutting. And that is that it is much much easier to avoid cutting on the side of the line, wood that you want to keep by simply lightly shading the waste side of the line. Wow! Of course that trick can also be useful too for cutting wood using regular single sided scroll saw blades as well. Very handy when making several very intricate designs where it can easily get a bit confusing during the cutting process of the design. Why I haven't thought of that one before, I'll never know. I must be a Rock! Again, TY for pointing that out ..... not to mention the several ideas you shared about the use of spiral blades.
@CharlesDearingScroller
Жыл бұрын
Makes me feel good that you found value in the video. Thank you so much for watching
@lloydbannister8062
4 ай бұрын
Well Charles I learned a lot from watching your videos and I still watch your videos when you post a new videos I love the cool scroll sawing you do I try to do it but it’s not that good yet
@ericlonadier3733
2 жыл бұрын
I'm glad I started with spiral blades. All I use and actually don't like the straight ones because I'm terrible with them. Enjoy your videos and also your patterns.
@CharlesDearingScroller
2 жыл бұрын
Thank you very much
@jonnycantwell6917
Жыл бұрын
BROTHERMAN YOU HAVE INSPIRED ME TO OPEN THIS DW788 I'VE HAD IT ALMOST A YEAR, I BOUGHT IT REALLY CHEAP AND PLANNED ON FLIPPIN IT, BUT YA KNOW HOW THAT GOES. I'M OPENI NG IT RIGHT NOW (AINT GOT A CAMERA) HECK IF I DONT USE IT MUCH THE PRICE I GET I SHOULD BE ABLE TO BREAK EVEN. WHO KNOWS I JUST MIGHT START PUTTING MY 40HRS/WEEK IN RIGHT HERE. ALL THANKS TO THIS CAT RIGHT HERE! GOD BLESS YOU MY FRIEND!
@CharlesDearingScroller
Жыл бұрын
Lol hell yeah. That's the beginning of a passion for creating that just might rule your life!
@TheMoppersmurf
2 жыл бұрын
Thank you for this! I use spirals when needed and flat blades when i can. They are both great but in my opinion they have theyr own purposes. Straight lines are easyer and smoother with a flat blade. What is most important to me is a really slippery smooth surface of the scroll table.
@CharlesDearingScroller
2 жыл бұрын
You're welcome and thanks for watching ;)
@unjje
2 жыл бұрын
Nice information! I just never got the hang of straight blades thanks Charles
@CharlesDearingScroller
2 жыл бұрын
You're welcome and thanks for watching
@twopoolpeople
5 ай бұрын
Thanks for the good video with any stupid music! I have spiral blades that I bought a while ago and never used them. You made me want to get busy and try them out before they are actually needed. Thanks again!
@PohlBarnProductions
2 жыл бұрын
good stuff Charles, Thanks for sharing!
@CharlesDearingScroller
2 жыл бұрын
Thanks for watching!
@sherwoodlayton9595
Жыл бұрын
Thank you for the instruction, very concise and useful.
@CharlesDearingScroller
Жыл бұрын
Thanks for watching and I'm glad you found it helpful ;)
@Sawdust_Factory
2 жыл бұрын
Thank You, spiral blades is the only thing I can cut with anymore.
@1linkbelt
2 жыл бұрын
I guess I need to try some.
@Sawdust_Factory
2 жыл бұрын
@@1linkbelt for me it was frustrating at first but after some practice it became easier. Now all I use is #0 to #3 spirals for everything
@1linkbelt
2 жыл бұрын
@@Sawdust_Factory Just order some from Amazon
@jasonrichelhoff4249
2 жыл бұрын
You thank good tips You are good teacher
@CharlesDearingScroller
2 жыл бұрын
Thank you! 😃
@raydillon4405
7 ай бұрын
Thank you, Charles.
@CharlesDearingScroller
7 ай бұрын
You're welcome and thanks for watching ;)
@daviddavis6065
2 жыл бұрын
thank you charlles i just got scroll saw and frist blade i put it was a spiral blade number 5 and i like
@CharlesDearingScroller
2 жыл бұрын
You're welcome and thank you for watching
@aussiman77181
Жыл бұрын
very nice tutorial video scroller man I really like it sorry I keep missing your videos KZitem don’t notify me when you’re on i keep seeing them later instead of live aussiman
@CharlesDearingScroller
Жыл бұрын
I thought I'd run you off somehow. Due to depression, I haven't been doing lives much, but hoping to get back to it. I also host scroll offs at the channel "Scroll Offs And More". I hope you'll consider subbing there buddy. Good to hear from you again ;)
@aussiman77181
Жыл бұрын
@@CharlesDearingScroller im always lurking about buddy and no i still luv ya just eather busy or keep missing were ever your at Aussiman
@Spain42
Жыл бұрын
Thank you so much. This was very helpful. New to you site… I’m a fan
@fredtaylor6771
2 жыл бұрын
Thank you for this video Charles. I will give them a try later.
@CharlesDearingScroller
2 жыл бұрын
Please do!
@mareasmith5697
Жыл бұрын
Thanks ror a very informative video, I have learnt a lot.
@CharlesDearingScroller
Жыл бұрын
That's great! So glad it helped. Thank you
@henrysscrollsawworks6917
2 жыл бұрын
Great explanation charles
@CharlesDearingScroller
2 жыл бұрын
Thank you kindly
@vincechoraszewski2394
Жыл бұрын
You're the man, I don't like spiral blades because I'm the back there's too much tear out, could you possibly help me with that?
@CharlesDearingScroller
Жыл бұрын
I'm afraid tear out is the down side of spirals. You get less using spirals with reverse teeth included.
@HarnealMedia
2 жыл бұрын
Good explanations Charlie
@CharlesDearingScroller
2 жыл бұрын
Thank you sir
@1957Ramboat
Жыл бұрын
Great video, Mr. Dearing. I’ve been woodcarving for less than a year and scroll sawing even fewer times (and only in regard to cutting out the wood patterns associated with my carving). I learned several valuable tips from your video. Thanks for posting it! I’m struggling with buying my first set of assorted scroll saw blades. The many various types of available blades is a bit overwhelming. Do you have any suggestions/guidance on choosing a good assortment of types of blades? And can you recommend a manufacturer of good quality blades?
@CharlesDearingScroller
Жыл бұрын
I only use Flying Dutchman blades. #3 and #5 because I usually cut large pieces. In fact you can get a percentage off of them by getting them from WoodenTeddyBear.com. If you get a gross or more, put CHARLES in the notes portion of the transaction. If you get less than a gross, put CHARLES in the gift card/discount box ;) As far as which Flying Dutchman varieties to use, the folks over at the site can guide you much better. Great folks over there! Thanks for watching and for the kind words.
@micmike
7 ай бұрын
Thanks, I was wondering if cutting plastic or plexiglass is possible and if there are cautions required?
@Denise_B17
2 жыл бұрын
Great video Charles
@CharlesDearingScroller
2 жыл бұрын
Thanks 👍
@Denise_B17
Жыл бұрын
@@CharlesDearingScroller you’re welcome
@MartyRaaymakers
2 жыл бұрын
Another good video. Thank you
@CharlesDearingScroller
2 жыл бұрын
Glad you enjoyed it. Thanks for watching
@casper1240
Жыл бұрын
Thanks
@CharlesDearingScroller
Жыл бұрын
No problem
@marcobazzucchi5563
Жыл бұрын
Thanks, very interesting 🙏🙏🙏
@CharlesDearingScroller
Жыл бұрын
Thanks for watching
@bobhoyer
2 жыл бұрын
thank you for sharing ...
@CharlesDearingScroller
2 жыл бұрын
You're welcome and thank you for watching ;)
@BarryM60
Жыл бұрын
Thank you for the tutorial and insight I have bought mine now and enjoy using them - early days. I did notice that when running them through my fingers, out the pack new, that they feel smooth in one direction and rough the other. There are no instructions on the pack that they should be inserted in any particular direction? I guess there is a choice though given how they feel. Which is the correct orientation smooth down or rough down, or doesnt it matter?
@CharlesDearingScroller
Жыл бұрын
You always want the teeth aimed down. That means smooth when sliding down and rough when sliding up. ;) Thanks Barry
@BarryM60
Жыл бұрын
Thank you! I'm surprised they don't state on the packaging but hey ho :) @@CharlesDearingScroller
@smeg8557
11 ай бұрын
I was wondering if you could help me? I recently purchased a scroll saw. I bought some reversed blades and I’m cutting out images on cedar boards, but I can’t keep them straight. There’s a lot a little cuts. I was wondering about using a spiral for that, I’m not really sure what to do or what type of blade to go with Let’s say something like a pumpkin cut out. I tried it with a reverse blade but I can’t get them to come out straight.
@endo6306
5 ай бұрын
Hi Charles, thanks for the video. What type of spiral blade are you using and how much tension do you put on the blade when mounted. I use Olsen blades but I get wiggly lines when I cut. The blade has a hard time to follow a straight line compared to my one sided blades. I'm thinking that I'm not tensionning the blade properly?
@CharlesDearingScroller
5 ай бұрын
Thanks for watching. It does sound like you need more tension on the blade. To be sure, I have a video elsewhere on my channel called "Anatomy Of A Scroll Saw" that mentions the sound you want to hear when it's properly tensioned. I use only Flying Dutchman spirals #3 and #5
@luisvillarreal2516
Жыл бұрын
esa hoja se sierra en espiral no se consigue en mi país y consegui hojas pero los dientes son ordinarios
@rogertyler3237
6 ай бұрын
Could I use One Of Those In My Rotary Tool?
@CharlesDearingScroller
6 ай бұрын
Afraid not. They're 5 inches long
@luizfernandodegouveagouvea7177
Жыл бұрын
Boa noite amigo ,; consigo cortar bem com essa lâmina espiral mas o problema maior é o acabamento da corte notei que deixa muita rebarba no corte , é assim mesmo ?
@CharlesDearingScroller
Жыл бұрын
kzitem.info/news/bejne/2H6owH2Ea3-mZn4
@jannineallen3450
6 ай бұрын
Is there a top and bottom for spiral blades?
@CharlesDearingScroller
6 ай бұрын
Yes. Always have the teeth aiming down
@jannineallen3450
6 ай бұрын
Thank you, I thought so. Tried it out and watched tour video again. So much easier to make smooth cuts.
@rosea4381
Жыл бұрын
Hello Charles I watched a video that you did on the Hegner. I see that you are using the seyco which one do you like better they have a Hegnar on marketplace for a $1000 it is the multmax 22V Hegner Is that good or bad price. It is a 1997 He said it needed a new Bellow. Thanks for your help and all your videos I love watching them, and learning from them.👍
@CharlesDearingScroller
Жыл бұрын
Honestly I love both saws. I have to say as far as clamping systems...the Hegner wins hands down. If the bellow is the only thing wrong with it, jump on it! Thank you so much for the kind words ;)
@rosea4381
Жыл бұрын
Thank you for your help. I did save up to get that hegner scrollsaw. 2 months Later🤞, it was still there and I did buy it. I hope to use some spiral blades as soon as I get some thanks for your videos & help!
@kevindoyle3510
10 ай бұрын
Great comment. That blade will not cut you until the human element is introduced. I have been making this point to my students for years
@alanwasserman8176
Жыл бұрын
Mr. Dearing I have a question I always use a flat blade on fretwork, could I use a spiral blade on a compound cut project I do not have any spiral blades and would like to try it if possible, thank you sir
@CharlesDearingScroller
Жыл бұрын
Yes, absolutely.
@PatrickSalisMEDIA
Жыл бұрын
How did you start the cut in the center of the board.
@CharlesDearingScroller
Жыл бұрын
By drilling a pilot hole. That's what is done with scroll sawing. You drill a pilot hole and thread the scroll saw blade through it. Clamp it and cut. ;)
@samuelpuckett7954
Жыл бұрын
Will it cut 3/4 inch piece or is it best to use thinner pieces with spiral blades? Are there different sizes? I just added a conversion kit so I could use spiral blades.
@CharlesDearingScroller
Жыл бұрын
It will, but if I have a choice, I always use thin wood
@danpeppers5564
Жыл бұрын
I have been scrolling since 1982, am i the only scroller in the world that feeds the blade from the top? I find it faster for me anyway.
@CharlesDearingScroller
Жыл бұрын
No sir you're not the only one lol. On a lot of saws I've topfed. On the Hegner I can't due to the upper arm not lifting
@1linkbelt
2 жыл бұрын
What blade speed do you use? (good video)
@CharlesDearingScroller
2 жыл бұрын
Thank you. I use #3 and #5 spiral blades by Flying Dutchman
@CharlesDearingScroller
Жыл бұрын
Apologies for missing this comment. I always turn the speed all the way up because it only cuts as fast as I feed into the blade
@Johnshorriblecardio
8 ай бұрын
To me it looks like a spiral blade is all you need for detailed work. I’m going to get some. I’ve only been scrolling for a few months but I’m decent at it. I think a spiral blade would be a game changer. Thanks for taking the time to share your experience with us.
Пікірлер: 101