Based on the setting here for a 4S battery the numbers would be High Volt 16.5 Alarm Volt 15.2 and Low Volt 13.5. I am using 16.8V 14.5V and 14V .
@anonuzer3394
6 жыл бұрын
Thank you my friend, went and bought one of these since I'm flying with 18650s. Now I can really keep an eye on the voltage. BTW, picked it up on Amazon, I think it was 8 or 9 dollars.
@NewBorn83
7 жыл бұрын
Thanks mate, you make my day!!!
@osvaldolopez4549
4 жыл бұрын
Try a little verbal instruction... makes more informative
@zacjohnson8404
7 жыл бұрын
worked for me, thanks boss
@theboywithacamera2093
7 жыл бұрын
I'm new to this stuff and didn't quite understand that stuff
@Deezarehairy
4 ай бұрын
Blurred can't see connections on reciever
@p.chuckmoralesesquire3965
7 жыл бұрын
awesome, good stuff man thank you!
@adityahi-tech1893
5 жыл бұрын
How do i connect sensor to FS iA10 A receiver. As there is no sense port.
@erikalemao322
7 жыл бұрын
Very good friend thank you for this information of telemetry .... and in question of long range how much you already arrived with this radio.
@BIG-MAD
5 жыл бұрын
Hello i am not the uploader of the video but i use flysky for my planes because of low prices and I hit 2.8 km with fs i6s and 3.1 km with fs i6x while flying my slowflyer plane equipped with sp f3 deluxe and a gps
@Rimrock300
3 жыл бұрын
Anyone knows, how to remove/lock telemetry at I6S / FS-IA10B ? I like to have 2 receivers in a model, and change between them, change model, without turning the other receiver off. With telemetry I6S TX won't let you change model before the current receiver is turned off
@irishguy200007
2 жыл бұрын
I'm totally confused
@dhavesy5730
4 жыл бұрын
You're just showing it,no any indication what is it or what it is for.
@montreechaiwog7245
5 жыл бұрын
FS-CVT01 can be used with 24vdc batteries ?.
@jamesmaccari6
7 жыл бұрын
thanks
@florinnegoita8846
4 жыл бұрын
that goes with x6b?
@krallopian
7 жыл бұрын
How would I use multiple sensors with the IA10B? I ordered the IA10B and would like to receive both Temperature and Voltage to my I6X remote. Any idea at all? Thanks!
@zhelev8134
7 жыл бұрын
I think every sensor has input and output. They connect in succession
@shawng5799
6 жыл бұрын
Or just power the RX from 2 cells via the battery balance plug ;) no need to spend anymore!
@bjarnehansen1101
6 жыл бұрын
Yeah, but you want to know the Voltage off the Lipo directly, so you would need to power the RX with (for the most people) 4s, but that would kill the RX
@shawng5799
6 жыл бұрын
LBLJLALRLNLE LHLALNLSLELN I have carried this out now and you just set the values for 2S. Then power from 2 cells on the balance plug,works fine. I even use the balance plug to power my video sender so I get no noise at all.
@bjarnehansen1101
6 жыл бұрын
@@shawng5799 Oh right! Didnt thought about that way, Really good!
@megahertz6787
2 жыл бұрын
@@shawng5799 yup using balance plug is really useful , you can power anything you want from it & even step down the voltage for more efficiency.
@JulioJairdeAlba
6 жыл бұрын
the "Sig.S" is the value of RSSI?
@die2end
6 жыл бұрын
Julio Jair de Alba yes
@notactuallyjeff3919
7 жыл бұрын
Will this work with 3s and 4s?
@swapnilsahu162
7 жыл бұрын
will the sensor occupy one of six channels of my ia6b receiver or there is a seperate port for sensor???
@zhelev8134
7 жыл бұрын
There is a separate port "sens"
@swapnilsahu162
7 жыл бұрын
Koko and what is the use of the port called 'servo' and 'ppm/ch 1'
@zhelev8134
7 жыл бұрын
Ppm is a kind of signal I have never used, otherwise the same port acts as channel 1. Also, I have not used a servo
@swapnilsahu162
7 жыл бұрын
Koko do you power the sensor by plugging it into the discharge port of the battery or to the xt60 plug??
Пікірлер: 38