Thanks Matt for all your help. Quick question, how do I find other power carvers in Kentucky or close to me?
@MattCarves
4 ай бұрын
Hey Jerry, thanks for watching. I'm not sure how you'd find local power carvers. Maybe Facebook or CarvingFusion has a strong Facebook group where you could ask that question. 👍
@timlist4173
7 ай бұрын
Thank you for the explaination and demostration. Very well stated. By the way, I like the burr/bit caddy. Hand made?
@MattCarves
7 ай бұрын
Yeah, that is hand made. Cheers for watching 👍
@urmelausdemeis3495
Жыл бұрын
Danke. Sehr hilfreich
@brokenmarbles70
Жыл бұрын
ty for the tutorials amazing work, may I ask what rpm do you run your dremel at for carving, cheers.
@MattCarves
Жыл бұрын
I tend to run just below full speed. I think I will do a video on this topic cheers 🍻
@jayc3110
Жыл бұрын
Matt, that was a great tutorial on the burrs you use and your Technique. Nicely explained in your soothing voice. Your camera work , with those beautiful close-ups it's much appreciated. We're learning a lot from you. Thanks and best wishes.
@MattCarves
Жыл бұрын
Thank you Jay, great feed back. 👍
@RichardBurrows-u8z
Жыл бұрын
Excellent tutorial Matt thank you!
@ParkBuffer65
Жыл бұрын
Thank you! What I saw is really very interesting and important! These are very good tips for making the work perfect!👍👋
@MattCarves
Жыл бұрын
Cheers for watching 👍
@Mike-ou5ps
Жыл бұрын
GREAT Video Sir. I seem to have a hard time finding those inverted cone shaped burrs. I don't even know what they are called. To describe...I can find the ones shaped like triangle, they're everywhere. But the ones which are opposite of that I dunno if I'm just a search engine dummy or what, bit I can't find them. Also, those flat disk diamond burrs you use. Can't find those either. Also also, I can't seem to find those burrs that are used for shaping/burning eyeball pupils...the ones that are hollowed out...what are those called? LOVE the video Sir. Thanks for taking the time for demonstrations.
@MattCarves
Жыл бұрын
Hi Mike, I do have an amazon link for those flat disk burrs in the description of that video, as for the inverted ones not sure about thosethe only one I have is from mastercarver.com. I dont tend to use those eyeball burrs I did see that sabertooth might have some I think they are called crosscutter burrs.
@Mike-ou5ps
Жыл бұрын
@@MattCarves thanks.
@stevew585
Жыл бұрын
Hi Matt, is that a suction table you are using ? I haven't got one as they're very expensive, I find the dust a major problem, my little shed/ workshop gets completely smothered in sawdust so I have to carve in the garden and it rains a lot in England...lol...bummer.
@MattCarves
Жыл бұрын
Hi Steve, sawdust is always a problem even with a suction table. I did a video on how I made that table kzitem.info/news/bejne/156H1Iuvn5VkoW0
@stevew585
Жыл бұрын
@@MattCarves Awesome, Thanks Matt. Your channel keeps getting better and better!
@cosmicfxx
Жыл бұрын
Great video, love the carving. Do you wear a mask while carving these? Not sure if I should worry about mask or not when carving small.
@MattCarves
Жыл бұрын
Cheers for watching Rob. I wear a 3m half respirator for all the carvings I do. It's amazing how much dust there is, and the super fine dust below 10microns is the really bad stuff. 🙂👍
@cosmicfxx
Жыл бұрын
@@MattCarves Good to know and thanks for sharing :)
@TheGreatest1974
Жыл бұрын
You are so skilled! I am only starting to think about wood carving, so I am watching tutorials like this one. My god, what an amazing thing it is to be able to create these wonderful things 👍🇬🇧
@MattCarves
Жыл бұрын
Thank you for watching and comenting. Have a great day 👍
@saafewolf69
Жыл бұрын
You showing the bits/burrs that you use and what for was very helpful and informative.
@MattCarves
Жыл бұрын
Cheers Kent 👍
@clairetolmie5640
Жыл бұрын
I always appreciate seeing which burrs to use for what purpose! I'm still adding to that list! 😊
@MattCarves
Жыл бұрын
Awesome Claire, yeah I got one of those wish lists too. 😀
@josemilian4167
17 күн бұрын
beginner value set of bits i bought suck, even to start. are the gold bits best for wood carving? the ones i have sort of float on wood and don't do much.diamond coated are ok but take ages to remove material. how do you know when they are worn out and need to be tossed out?
@MattCarves
17 күн бұрын
the best burr for removing wood is the kutzall very course flame burr, your gold burrs are good for fine details and the daimond burrs are great for some removal but also a fine finish. Kutzall burr last about a year for me
@josemilian4167
17 күн бұрын
@@MattCarves oh ok thank you i thought mine might have immediately worn out since they were so cheap. I will invest in some kutzalls thanks!!!
@oldncarvingJohn
Жыл бұрын
Absolutely brilliant. Your explanation is so clear and your skill amazing.
@MattCarves
Жыл бұрын
Cheers John. Hope your carvings are going well.
@lechatbotte.
Жыл бұрын
I just love watching you carve. I like that you can soften the features even after you carved away material
@MattCarves
Жыл бұрын
Thanks Linda. Have a great day.
@jimbenge9649
Жыл бұрын
Great video. This is so useful. Thanks Matt. 👍
@MattCarves
Жыл бұрын
Cool cheers Jim
@markanthony559
Жыл бұрын
👍👍👍 looks awesome Matt. Also Happy Easter!🐰
@MattCarves
Жыл бұрын
Happy Easter 🐣.
@julieakehurst2754
Жыл бұрын
Very informative and clearly explained 😊
@MattCarves
Жыл бұрын
Thank you Julie hope you have a great day. 👍
@justcarverob9389
Жыл бұрын
Cool video Matt I appreciate the tips stay safe just carve
@MattCarves
Жыл бұрын
Thanks Rob, hope your back is a better or getting better.
Пікірлер: 42