Great timing, I had ordered some coolant and an aluminum heater hose inlet a few days ago with intentions to do this. Just grabbed one of the kits, seems the way to go.
@Rythecarguy
Жыл бұрын
Heck yea. Hope it helps.
@boatsail1
7 ай бұрын
thanks
@rogerdinarte6863
2 ай бұрын
Well explain video, ive had this tool for years and now i know how to use it because of your video. Thank you, im going to use it haha.
@ahmadghosheh3104
Жыл бұрын
I have similar kit, more fittings for different cars, I never used the vacuum part, it seemed kinda complicated but it doesn't look like it. Thanks Ry, will give it a try.
@Rythecarguy
Жыл бұрын
My pleasure! If you didn't use the vacuum part what did you use it for?
@ahmadghosheh3104
10 ай бұрын
@@Rythecarguy My kit has all the adapters for different radiators and a hand pump to put pressure in the system and find leaks. It also has the vacuum part with hoses.I used it to test coolant systems. Bought it couple of years ago when I got a 2003 Camry from the auction with coolant issues, head gasket, and bunch of other problems. It was a project car. Since then I used it when diagnosing coolant leaks. Works pretty good. I have a small hotdog type compressor so I don't get much air flow needed to vacuum the system.
@Rythecarguy
10 ай бұрын
@@ahmadghosheh3104 Great point, I used it to test mine not too long ago on the silver Xterra. Unfortunately, thats how I found out that the heater core was bad.
@LittleBJT
Жыл бұрын
Great explanation and video! Short, and to the point
@Rythecarguy
Жыл бұрын
Thanks!
@JordanPetersonTech
Жыл бұрын
Awesome video bro. Easy to follow.
@Rythecarguy
Жыл бұрын
Thanks man! I appreciate it.
@bikecrazy001
9 күн бұрын
Great vid, How much psi do we need on the air compressor for creating a vaccum?
@smokey2much420
3 ай бұрын
What size air compressor are you using? Does it matter or would the size just determine how fast the vacuum is created?
@XtremeBUZZ
Жыл бұрын
Keep up the great content Ry!
@Rythecarguy
Жыл бұрын
Thanks man!! 💪🏻💪🏻
@intercomking4188
12 күн бұрын
Such a great video,
@Rythecarguy
12 күн бұрын
Wow, thanks. 😊
@homewrecker44
9 ай бұрын
Instead of removing the reservoir were you not able to connect directly to the Rad with a Cap Adapter? Unless this vehicle has no filler cap at the Rad and you have to use the reservoir.
@joshuawalters7377
22 күн бұрын
If i just drain the radiator or if I drain the radiator and engine block…is the vacuum fill the same?
@msburrage74
3 ай бұрын
So I have a question. I just did this same system but when I was putting the coolant back in it dropped to 0 really fast, like a few seconds and even though the coolant initially went thru the tube the level on the container I had the coolant in didn’t move. I drained the radiator also and got right at a half of a gallon out. So after I took the device off I had to pour that half gallon back into my radiator. So what did I do wrong and do I need to do it again? Seems like my wrangler is still running hot from time to time still
@datboi8140
Жыл бұрын
Might be dumb but doesn't the thermostat open with pressure created from the coolant heating up? So you'd have to remove the thermostat?
@rcnewcomer7304
Жыл бұрын
Thermostat opening by temperature, not by pressure.
@CJ.A-C
20 күн бұрын
ditto to man before. Just bought a new one from Vevor, which has every application going. Bought it from eBay roughly £60. Great video, very well explained.
@walther89
Ай бұрын
can i do it when there is coolant all ready in ?
@hugba
8 ай бұрын
Hey doggy. Great vid. Will this tool work if the coolant system is like 95% full? Or does it have to be empty?
@Rythecarguy
7 ай бұрын
Not to fill but probably just fine to burp/bleed it
@anoldfriend3901
Жыл бұрын
How do we do this on an 2007 Titan if we didn’t drain the whole system? Also I noticed in the service manual it says to do it from the radiator and place an non venting cap on the reservoir. Can we still use this vacuum tool if we didn’t completely drain all the coolant? Meaning we only drain from the radiator.
@SaycoPworrell
10 ай бұрын
You gotta have a vacuum in the coolant system. So when you start pulling vacuum, that remainder amount will be sucked out.
@johnnywalker4409
5 ай бұрын
This just answered my question I have coolant still in the system wondered if it would stay
@isaachorton51
8 ай бұрын
Someone put an aftermarket reservoir on my car it wouldn’t fit so I put it on the radiator directly it works vacuums it but when I close it off it sounds like it’s gargling in my reservoir or something and the pressure is escaping do you have any recommendations?
@Rythecarguy
8 ай бұрын
You’re pressure relief valve is probably opening. You need to block it off like i did in the video. Stick your finger over it and see if the gurgling stops.
@johnnywalker4409
5 ай бұрын
Young Man, does the coolant system have to be empty before doing a vacuum refill? I only removed an upper hose so it may still be half full
@Rythecarguy
4 ай бұрын
No it does not. I would still use it if I only did a partial drain
@johnnywalker4409
4 ай бұрын
@Rythecarguy did it and worked fine, Thank You
@hjfcoco
10 ай бұрын
What if the system is half filled with anti freeze, will this still work? Or the system must be empty?
Пікірлер: 47