Tip for you lappers ! Figure 8 Be patient. When using grit that is properly matched to the object being lapped, a typical minimum lapping time is 20 minutes for fine abrasives and 30 minutes for coarse abrasives. After the initial lapping session, clean the object and check the progress. Additional 10 to 15 minute sessions may be needed to achieve the desired results. • Use a figure-eight pattern. Regardless of the object being lapped, optimal results are achieved when the object is moved about the lap in a long, slow figure-eight pattern, as shown in Figure 8. This technique continuously redistributes the slurry around the lap, keeping it Figure 7: Lapping set-up. Figure 8: Figure-eight pattern
@Runeeraaja
Ай бұрын
what is the torque to put the injector frame to the headgasket?
@Dyngolf2
Ай бұрын
Thanks without you I could not know how to rebuild this.
@JoeisHungry
Жыл бұрын
you have to have a pop tester and shim kit or all this is for nothing
@jankristianiversenmagnusse4089
Ай бұрын
What grid sandpaper do you use?
@joshsniezak2346
3 жыл бұрын
Does the part number dn0sd273 cross reference to the part number you posted?
@TheDZOLE
3 жыл бұрын
Thank you, I have to change those nozzles i have lot of white smoke at the start and after that black smoke constantly when hit the pedel ... Maybe this will helps me
@captlarry-3525
11 ай бұрын
use standard nozzles, white smoke, check head gasket
@captlarry-3525
11 ай бұрын
Injector tester about $80..very necessary as is the shim to set breaking pressure. and knowing pattern is right, and not dribbling. Otherwise what's the point ?
@Thumbnail_Investor
4 жыл бұрын
Glad I saw this video I was gonna send mine out! Looks real easy!
@marcobecker906
6 ай бұрын
thanks, i needed that. It is help full. Geet video. thanks...
@ilyatkachev3900
2 жыл бұрын
My diesel 85 jetta is not starting i got new glow plugs for it , it has diesel running through and into the engine i cleaned my injectors but when i crank it it has oil leaking above the oil filter and the oil light blinks please helppp
@fil1329
Жыл бұрын
The salt on your skin can ruun an injector And that thing is a needle valve
@71iron13
7 ай бұрын
Excellent video. Thank you!
@zragevii4705
3 жыл бұрын
Could anyone suggest a good but cheap set of crows foot attachments? Also, any tips to keep a rev limiter while still doing something like the governor mod?
@vyla2581
2 жыл бұрын
is there a requirement for what Newton force to use to tighten the injectors? When I screw the injectors back into the motor for me they are in a row and it is difficult to push the hoses back
@bro8759
Жыл бұрын
What grit sandpaper do you use to sand down the faces of the injector?
@hectorhernandezperez6140
2 жыл бұрын
Donde conseguiste las nozzle y a que precio?
@senorpatillas8959
2 жыл бұрын
Is there a different manual for a 85 1.6 na?
@kreparAZ
4 жыл бұрын
looks pretty easy man. good video! keep em coming dude! good shit!
@OsmanGaziPasha
Жыл бұрын
Thank you
@jamesdixon3507
2 жыл бұрын
Is the nozzle the same for na and turbo cars?
@captlarry-3525
11 ай бұрын
no and also different for auto or manual, match to engine model
@tehdreamer
3 жыл бұрын
I have a 1994 VW LT35 bus with the same type injectors, thanks for the video it helped to get reassured. The manual says always to change the heat shield when removing the injectors. Would if thats really important because even though I have a spare, i cant get the bloody old ones out, they are stuck there good...
Пікірлер: 25