Note: MobiFlight only supports 7 segment displays with max7219 chips.
@brianfletcher7449
3 жыл бұрын
Great vid, but my fave part is always the opening theme song. Thumbs way up!
@CaptainBobSim
3 жыл бұрын
Same here! :) Thanks for watching
@kfgaming2005
5 жыл бұрын
Great video! Very helpful!
@CaptainBobSim
5 жыл бұрын
Thank You! I am glad this helped!
@filipeferreira4630
3 жыл бұрын
Hi Captain Bob! First of all congratulations for you work! You pushed me to make my own panel switch and autopilot module, and i dont understand to much about eletronics :b Everything is going great exept the 7 segments displays. I just bought two of them with 4 digits but there is no DC Pin out on this displays. Can you tell me if i can use them? :s thank so much :D
@CaptainBobSim
3 жыл бұрын
Hello! Could you send a link to the 7 segment displays? I'm not sure which ones you are talking about. Have a great day Fillipe! :D
@filipeferreira4630
3 жыл бұрын
Hi @@CaptainBobSim :D I already found the issue. Apparently the mobiflight only supports 7 segments displays with max7219 chips! It took me sometime to found this information x) I will start building my humble flight box! Lets see if everything goes right! Finger crossed ahahaha Keep doing what you do ;D
@arduinomaquinas
Жыл бұрын
cool job, awesome project, by 👋👋👋Brazil !
@CaptainBobSim
Жыл бұрын
Thank you!
@stevechalmers3607
3 жыл бұрын
With release 8.2 much has changed with Mobiflight since you recorded this video. SimConnect and A-Vars have changed how a 7 segment LED can be implemented in Mobiflight. Should be even easier, but not working for me. I am missing something, perhaps others are too. So, asking you to think about the need to update this video (and perhaps others) to using SimConnect instead of FSUIPC.
@CaptainBobSim
3 жыл бұрын
Hey Steve! MobiFlight just released 9.0! I'm slowly making the change away from FSUIPC (but not 100% appealing to me because X-Plane gets left in the dark). Sebastian from MobiFlight makes release videos with most versions of MobiFlight that should help a little. I can't promise to update MobiFlight Tutorials to the latest version of MobiFlight, the software advances so quickly, and I don't always enjoy editing my footage down.
@dannyvr1225
6 ай бұрын
Hi Captain, for the max7219 (8 digits): is it possible to split 1 display into 2x3digits (2digits unused)? and then control these two pieces separately? This, for example, to display the Course (3 digits) and ias/mach (3 digits) in 737 with one MAX7219...?
@CaptainBobSim
6 ай бұрын
Yep! DIY 737 sim has a great article for this, which I use whenever I need to do anything with wacky MAX7219 displays It's since been broken: www.737diysim.com/post/737-radio-7-segment-displays Basically follow the pinout of each module and try to pin it into the 4 digit displays: i.stack.imgur.com/vJzZu.png The main difference should be the digit pin
@NickWilmans
5 ай бұрын
It's looks easy. But if you don't know which wire you have to put in which port, then you have to spend a lot of time to figure out by watching tutorials en reading forums. You better use this time to save some money and work overtime to buy a complete plug and play device.
@CaptainBobSim
5 ай бұрын
This is true, but what's the fun in that! 🙃
@zz-mt5zf
5 жыл бұрын
Thanks this was very helpfull😁
@CaptainBobSim
5 жыл бұрын
Oh good! I am glad this helped!💥🌟👍
@zz-mt5zf
5 жыл бұрын
Captain Bob Hey how many segment display can I connect to one Arduino mega?, if you know🤔
@CaptainBobSim
5 жыл бұрын
@@zz-mt5zf Theoretically you could use up to 20 on one board (as there are about 60 usable pins) but the USB power would likely not be sufficient. MobiFlight officially limits 4 displays per MobiFlight Arduino (5th question: www.mobiflight.com/en/documentation/faq.html ) There are only (3) 5 Volt Pins, so you would have to use a breadboard for more (There are also 3 ground pins, so a breadboard, or similar solution is needed anyways.) 😃 You can achieve more by wiring displays together. I will show this in a future video 😎 MobiFlight supports up to (8) 8 digit - 7 segment displays daisy chained together so the maximum is up to 32. (I typically use 3 displays per arduino, and daisy chain them 3 long at most.) Great Question! 👍✈⭐🌟
@zz-mt5zf
5 жыл бұрын
Captain Bob Yeah thanks for the super great information, I was thinking about 6 of these 7 segment display to connect to the Arduino mega😆😁
@CaptainBobSim
5 жыл бұрын
You are welcome! Remember that you can use switches as well as the displays, as you still have about 40 pins. Switches don't draw power :)
@sanderslette6341
5 жыл бұрын
Awesome!
@CaptainBobSim
5 жыл бұрын
Thank you! There was a solid 15 minutes of "yay me I got it to work" dancing! 🤣🤣
@sanderslette6341
5 жыл бұрын
😂
@116darkshooter
2 жыл бұрын
Can I use this method and FSUIPC to make it work with FS2020?
@CaptainBobSim
2 жыл бұрын
Yeah! You can use FS2020's FSUIPC or MobiFlight's built in Events
@ACHALAMI
3 жыл бұрын
it is possible to use 1 Arduino for multiple indicators or every indicator needs its arduino ??
@CaptainBobSim
3 жыл бұрын
You can have up to 10 seven segment displays if I recall correctly. You can use the other 60 some pins for other components
@Jake-yv3kf
5 жыл бұрын
would this work with Xplane11?
@CaptainBobSim
5 жыл бұрын
I am not sure. Here is the X-Plane MobiFlight Forum, this might be helpful: www.mobiflight.com/forum/category/10.html You would use XPUIPC instead of FSUIPC, as said in this forum. www.mobiflight.com/forum/topic/525.html Great question!
@codingvio7383
4 жыл бұрын
Do I need an arduino MEGA? Or can I also use an Arduino UNO, because I don't have the mega board. Because this is really cool
@CaptainBobSim
4 жыл бұрын
You _can_ but it's no longer supported, and has some bugs in the code. Look into the MobiFlight forum for this. I would highly recommend the mega, it's only $15 online so not too big of a deal (compared to other boards)
@desktop-master3505
4 жыл бұрын
Idk if you will See this, but i watched your Videos for a long time and i always wondered, do i really nned like 50 Ardurinos just to make like an Auto pilot segment or is there a Trick to make more segment displays wich all work individually?
@CaptainBobSim
4 жыл бұрын
You can, just set them to different devices (use different PIN numbers). I think you can hook up 10+ 7 segment displays?
@desktop-master3505
4 жыл бұрын
@@CaptainBobSim ok thank you
@boryswiniarczyk7314
5 жыл бұрын
Thank you for this very youseful tutorial :)
@CaptainBobSim
5 жыл бұрын
You are welcome! :)
@reivsinim7031
3 жыл бұрын
Hello my display is working but when I for example press test where u can chose the numbers which represents there are just showing weird led not the one I choose when I run the simulator and press start it just showing random numbers and letters. When I change the numbers in the simulator fs2020 then they are changing as well but to something other weird numbers and letters
@CaptainBobSim
3 жыл бұрын
It's hard for me to replicate your results. I assume you are talking about the "Transform" window when you are talking about changing the values. In the display tab, the 1-8 numbers are the digits you control, not the numbers on the digit. This is likely due to some bad 7-Segment displays (sometimes the soldering on them isn't the best). Have you tried this with a different one? I haven't tried this tutorial with FS2020, so this might be an issue as well 🤔 On the MobiFlight page is the "Output Value" changing to the desired number?
@hashimiqbal6822
5 жыл бұрын
How did you learn to use arduino, I would like to learn. How do you know what wires to plug where?
@CaptainBobSim
5 жыл бұрын
I learned by looking at Arduino Wiring schematics and looking at the MobiFlight Tutorials. This diagram helps a little: www.circuitstoday.com/wp-content/uploads/2018/02/Arduino-Mega-Pin-Configuration.jpg The ground pins are negative, and (Sometimes black wire). The 5v pins are positive, (Sometimes red wire). The digital pins are where you can plug your switches into, and the positive side of LEDs or other electronics. The analog pins are typically unusable with MobiFlight. You can email me if you need more help: CaptainBobSim@gmail.com
@chrisparks262
3 жыл бұрын
Will this work for Arma3
@CaptainBobSim
3 жыл бұрын
MobiFlight is not currently compatible with Arma3 using outputs.
@tarikb.2352
2 жыл бұрын
Hi @captain Bob thanks for sharing. Just a doubt my 6 digits 7 segments don't have the CS pin. Others are OK. In my case, Mobiflight add device with error :( any advice about that ?
@CaptainBobSim
2 жыл бұрын
Is it a MAX7219 chip? Only these are compatible with MobiFlight currently.
@tarikb.2352
2 жыл бұрын
@@CaptainBobSim thanks! Nope it’s a TM1637 :( i choose it because many sizes and color choices… do you recommand a specific model 0.36 Max7219 ? I’m looking for 4 and 6 digits display :)
@CaptainBobSim
2 жыл бұрын
@@tarikb.2352 Hmm. I don't know if there's a 4 digit display, but if you get the green colored displays, you can remove the pins and extend only 4.
@tarikb.2352
2 жыл бұрын
@@CaptainBobSim hi ! I try today with a Max7219 (digits lights ON) but 0 display/light when I upload device setting on Mobiflight :(
@eliottferry3634
2 жыл бұрын
Is it working with fs2020 ? Thanks !
@CaptainBobSim
2 жыл бұрын
Yep! You just need to use MSFS outputs instead of FSUIPC outputs (and select from the list for what you want)
@eliottferry3634
2 жыл бұрын
@@CaptainBobSim thanks 👍👍💪
@MohamedSherif-xr4lg
3 жыл бұрын
Can i have the program that is uploaded to the arduino for the 7 segment please ??
@CaptainBobSim
3 жыл бұрын
Negative. I don't have it anymore. My goal is to teach you to know how to make it, not to just to copy/paste- there are many things that can go wrong just copy pasting. Let me know if you have any questions with this!!
@TheTribeitaly
4 жыл бұрын
hi, i'm trying to built a 737 OH, so now i'm trying to connect a switches and led to mega board, but i've a problem when i assign a annunciator for example fuel pump low pressur work fine but when ia turn off ground power and battery switch the led of fuel pump still on, how can i solved this problem?
@CaptainBobSim
4 жыл бұрын
Hey Simone, This sounds like a more complicated problem, I might ask this on the forum: www.mobiflight.com/forum.html
@TheTribeitaly
4 жыл бұрын
@@CaptainBobSim thank for for the answer, I solved the problem, i've another westion (sorry if you took advantage of it) i can connect a lcd display with two rows? is the procedure like the one described in the video?
@TheTribeitaly
4 жыл бұрын
@@CaptainBobSim thank for answer. I can connect a lcd dipslay with two rows? is the procedure like the one described in the video?
@CaptainBobSim
4 жыл бұрын
@@TheTribeitaly It is quite similar, look up "MobiFlight LCD tutorial", and you should find a good video on it (it is in spanish)
@TheTribeitaly
4 жыл бұрын
@@CaptainBobSim thank, you're great
@harpoon_bakery162
4 жыл бұрын
can you get 3 digits to the right of the decimal like most glass cockpits have on their G1000's ext? thx
@CaptainBobSim
4 жыл бұрын
Yes, you'd just activate the 6th digit as well. I believe the output value is in 122.800 format.
@harpoon_bakery162
4 жыл бұрын
@@CaptainBobSim ok, thanks. the logitech panels only allow 3.2 or ###.## so in other words, you can't see what frequency you are on.
@CaptainBobSim
4 жыл бұрын
Here's a picture with a ###.## radio, they are common. www.aopa.org/-/media/Images/AOPA-Main/News-and-Media/Publications/Pilot-Magazine/2018/1801/1801p_pe_technique/1801p_pe_technique_16x9.jpg?h=675&w=1200&la=en&hash=218AF1F90B8E354B241E3383398DBF80 To my knowledge, most frequencies increase by .025 each step, so only the .## is needed to tell which step it's on. I've seen some exceptions though.
@harpoon_bakery162
4 жыл бұрын
@@CaptainBobSim -- gotcha, i will study more on this topic and thanks kindly.
@MiguelMadrid-es7ij
3 жыл бұрын
Hey captain Bob can i use two of these with an arduino nano?
@CaptainBobSim
3 жыл бұрын
Nano will not work with MobiFlight, but Pro Micro will. Yes, you can have more than one :)
@MiguelMadrid-es7ij
3 жыл бұрын
@@CaptainBobSim thank you so much :) i will buy many pro micros and one 2560 mega.
@CaptainBobSim
3 жыл бұрын
@@MiguelMadrid-es7ij No problem! Have a nice day!
@reivsinim7031
3 жыл бұрын
Will this also work with FS2020?
@CaptainBobSim
3 жыл бұрын
studio.kzitem.info9Ot8EALj99o/comments Heck yeah! Different steps to install mobiflight, but it should work the same :) Happy Landings!
@reivsinim7031
3 жыл бұрын
@@CaptainBobSim cheers mate
@xFrayx
Жыл бұрын
my 7 segment display turns on all its lights but nothing else, i tried everything. Can somebody help me?
@CaptainBobSim
Жыл бұрын
Have you confirmed its a MAX7219? Have you triple checked your wiring? Maybe try different wire (not good connection) Have you tried with a different display? (Sometimes these can be duds)
@xFrayx
Жыл бұрын
@@CaptainBobSim yep it's a MAX7219, I checked my wires several times. I have 10 of them, I already tried to change
@CaptainBobSim
Жыл бұрын
@@xFrayx Are yours common cathode or common anode?
@xFrayx
Жыл бұрын
@@CaptainBobSim everything is settled, after several tests it finally works! the problems were the wires (poor contact) and the number assigned to the display. The only remaining problem is that the comma takes up a whole digit slot.
@CaptainBobSim
Жыл бұрын
Sweet! Usually it's a connection problem/dud. Multiply it by however many digits are after it to get rid of the comma taking a whole digit 👍
Пікірлер: 80