nah the stiff lever is better to not accidentally hit it.
@mikedavis8239
2 жыл бұрын
Perfect steps for adjusting the blades and lever switch! For some reason the moving blade won't adjust beyond a certain point which has a slight gap between the blades on my corded masters the cordless is set the closest.
@ezbladeshavingproducts
2 жыл бұрын
Thanks for watching
@7emiliano1landa3
2 жыл бұрын
I just put a few drops of oil and firmly but gently worked the lever on a daily until it became smooth
@adriennemcmillan647
4 жыл бұрын
Very helpful!!! Thank you!!!
@ezbladeshavingproducts
4 жыл бұрын
You're welcome!
@NVTwistedProductions
3 жыл бұрын
I loosened the lever a little now when I press on someone's head it pushes the teeth in .. I should have just left it
@braygettingmoney
2 ай бұрын
Can you do a video on how to make the lever stiff on the 66360 model
@NVTwistedProductions
4 жыл бұрын
This was fantastic thank you... One question. When I tightened the blade into position... It doesnt matter how tight i tighten the screws i can still move it a little bit with my hand .. Any tips??
@lomaxcharles
4 жыл бұрын
I’m having that same issue don’t know what to do smh
@NVTwistedProductions
4 жыл бұрын
@@lomaxcharles ugh
@Alanisrael12
3 жыл бұрын
did you end up fixing it ??
@Alanisrael12
3 жыл бұрын
i have the same problem
@mr.marquis9081
2 жыл бұрын
Why is it that the masters never close to the first notch it’s always in the middle.. since that’s a fact do I just go straight to the 3rd notch from the close position or barley open it to the second notch and then proceed to the 3rd
@TMichael1415
4 жыл бұрын
I have a Andis Master Clippers and when I cut the blade will some move when I have the clipper blade closed. How do I get it to stop moving.
@NVTwistedProductions
4 жыл бұрын
I am going through the same.. When i gapped them and tightened... It still moves a bit when i nudge it with my fingers
@Alanisrael12
3 жыл бұрын
@@NVTwistedProductions did yoi ever fix it ??
@NVTwistedProductions
3 жыл бұрын
@@Alanisrael12 I ended up getting the cordless ones and they don't move like that
@Alanisrael12
3 жыл бұрын
@@NVTwistedProductions i have the cordless masters and i have tightened the screws all the way but can still move it with my fingers , you know what i could do ??
@elderreyes3782
Жыл бұрын
Hello, I took my blades off to sharpen them and clean the clippers. After I put the blades back on, they dont cut anymore. they make a noise and the blades move but theyre not cutting. I tried to pull the tension spring to give it more tension but it didnt work. Can you tell me or show me in a video how to put the top blade back on over the pring to see if im doing it right? Please Help!!!!
@ezbladeshavingproducts
Жыл бұрын
Do you have a wired masters?
@kimhenly3548
2 жыл бұрын
Can you do a video on how to replace the lever?
@ezbladeshavingproducts
2 жыл бұрын
Definitely
@Smokie1013
2 жыл бұрын
Does the clippers bite on your guards when you zero gap it?
@ezbladeshavingproducts
2 жыл бұрын
It will a little in the beginning.
@jonathanmelendez7410
3 жыл бұрын
Would this make it easier to fade out the guide lines?
@ezbladeshavingproducts
3 жыл бұрын
yes it would
@jdub630
4 жыл бұрын
Nice video.
@ezbladeshavingproducts
4 жыл бұрын
Thanks!
@chonrodriguez7572
3 жыл бұрын
any tips on how to quiet this machine it is way too loud 👂
@bossbig6213
3 жыл бұрын
when I put the maximum 0 bites the nozzle, what should I do?
@naqvikidzentertainment
4 жыл бұрын
Hi Can you zero gap the Andis MLC straight from the box? I’m having problems with zero gapping the whole blade only half attends to zero gap and the other half doesn’t, I just don’t know why. As in the video it’s all straight but my isn’t. I’ve been told that I need to change the blade is that true? Any help will help. Stay safe.
@edwinhernandez6643
3 жыл бұрын
My Andis Cordless Masters have gotten soo loud after like 6 months. They were always louder than the corded ones but not they are even louder. Any idea on what it can be? Tension?
@ezbladeshavingproducts
3 жыл бұрын
Not sure that seems to be a on going problem
@shannonlazcano8506
3 жыл бұрын
I’ve seen videos how to adjust the sound, by adjusting the the screw on the side of the body, search for the videos regarding this issue
@letsgoletsgoletsgoletsgoletsgo
2 жыл бұрын
@@shannonlazcano8506 I think that's a corded trick
@joelouis1889
4 жыл бұрын
Why do all these funny ass barbers zero gapping everything? They're good the way they are
@NVTwistedProductions
4 жыл бұрын
U aint gonna get the bottow line out of a bald fade with them then 🤷🤷
@NVTwistedProductions
3 жыл бұрын
@Rob Guy 100 pct.. Or he sure as heck aint doing fade work .... Bowl cuts and mullets
@Therealvielo
3 жыл бұрын
@@NVTwistedProductions 🤣🤣
@shooz4unme
4 жыл бұрын
Q: Can this be done the same way for on Andis T Outliner as far as zero gapping?
@jdub630
4 жыл бұрын
Yep.
@ezbladeshavingproducts
4 жыл бұрын
Yes You can! We will make a vid on it!
@WilsonAutoworks
4 жыл бұрын
Just bought these Andis Masters and i cannot get them anywhere near 0. The closest i can get it is like a 16th of an inch from being even with the bottom blade. Do you think this one might be deflective? No issue with 0 gapping my Andis trimmers. Good lookin on the lever tip!
@Mike-hy8cs
4 жыл бұрын
Honestly its not worth zero gapping them in the first place. If you truly zero gap it it eats at the andis guards. Get it as close as you can without it eating your guards and you are good to go. It takes out the trimmer line no problem as long as you are not setting in your trimmer line harshly. Its a tapered blade anyway so if you want to remove harsh trimmer lines its better to use a fade blade or just use a different clipper. Personally I dont like setting harsh trimmer lines anyway so i never have an issue with this clipper.
@Peter-hw1yx
3 жыл бұрын
@@Mike-hy8cs I always set harsh lines with my trimmer. How do I stop?
@Mike-hy8cs
3 жыл бұрын
@@Peter-hw1yx instead of putting it in like you are lining someone up.. Use it like a clipper and scoop slightly while making the line. Making a super perfect skin guideline is a waste of time. Why? Because you are going to fade that line out anyway. As long as both sides look similar you will have an even fade when its finished.
@Peter-hw1yx
3 жыл бұрын
@@Mike-hy8cs should I just use my andis master then instead of my trimmer all together?
@Mike-hy8cs
3 жыл бұрын
@@Peter-hw1yx you can a lot of people do it like that. Personally since i need to be efficient with my work i use a zero gapped trimmer first . If you use clipper first you will still need to go underneath it with a trimmer
@breakan
4 жыл бұрын
Why it’s so expensive bro
@ezbladeshavingproducts
4 жыл бұрын
Not sure why they are
@garyquintanilla4954
4 жыл бұрын
I’ve used cord and just bought the cordless . I felt the same way but I think for the cord price is good. Cordless I think you are over paying maybe 30-60 $ plus it has no clips lol Andis products been good so far
@baljinderhundal8368
2 жыл бұрын
It makes too much noise . We don't like it
@shendetgashi2100
3 жыл бұрын
Stop zero gaping every type of clipper youre just going to destroy them
Пікірлер: 59