There's a definite breach of protocol here...only the boss is wearing safety sandals...
@mlt6322
14 күн бұрын
Not to mention all the loose clothing around the machines.
@apex107lrp
13 күн бұрын
@@mlt6322 Hell, most of these videos should be subtitled "How Not To Run A Machine Shop Safely"
@robertteap8052
26 күн бұрын
I would guess that it is an impeller housing for either a water pump or, if used in the reverse, as a turbine housing for a water driven generator. With water entering through the side "fins" and exiting through the large lower opening as it turns the impeller,
@martinburwell4214
13 күн бұрын
base for a raymond roller mill, bull ring fits into top hole, gearbox fits in the bottom and wear plate bolt into the ports to stop it getting into that condition
@frozendude707
10 күн бұрын
Seems to check out, looked at some of the principals of operation for a raymond roller mill, and it does look like that, with the fins shaped that way because of resource extrication being toroidal pressured air, so it is pneumatics and not hydrolics as people seem to assume. Nice catch.
@casper8969
13 күн бұрын
We can see that the cast pedestal was sheared by torque. If it's returned to service as it is the repair will not last.
@lewjones7272
29 күн бұрын
I even enjoy watching the short - stroking planer in the back ground!
@charlesdeilke8364
29 күн бұрын
Not Hydro. Some sort of large slurry pump part. Waste water or industrial.
@FosterGoat
29 күн бұрын
Agreed. Look how the vanes are worn. Maybe part of sand dredge.
@thepubliceye
14 күн бұрын
That's just what I thought.
@Antuan2911
29 күн бұрын
Has something to do with hydroelectric turbine...
@emilchouster787
29 күн бұрын
It used to be the stator of hydroelectric turbine, what is it now only God knows.
@nicodesmidt4034
28 күн бұрын
Think it’s broken in half
@28704joe
24 күн бұрын
My guess its use is in rock crushing
@kwinterburn
14 күн бұрын
Looks like the vortex ring off a turbine the turbine itself is bolted to the top ring, looks like it was unbalanced and cracked the supports
@patverum9051
14 күн бұрын
Base of a Raymond mill, for crushing gravel.
@blandp11
29 күн бұрын
Looks like something is supposed to flow through it, like a stator vane. But what substance? Looks too crude for water. Grain? Gravel?
@cameronlilly4814
29 күн бұрын
Maybe a stator/base for an O-Sepa classifier for a cement plant? 'Couldn't find an exploded-view drawing quickly, but it will be something like that. 'Problem is that without knowing what it's for, it's difficult to get it even remotely close to correct.
@billguernsey6419
29 күн бұрын
Sewage treatment possibly.
@steveingalls6798
28 күн бұрын
Gotta love the safety footwear 😂
@MurlWatne-io2bo
29 күн бұрын
I think the main piece is cast iron n doesnt need any lube to drill.
@lewjones7272
29 күн бұрын
I think I saw a dean smith and grace- oh my!!!
@jeffreyyoung4104
11 күн бұрын
Sad that many of the companies in America sent their work out to be performed in places like this. But then, all of the safety and other government mandated protocols have made working in America too expensive to follow the rules and labor requirements here. But the quality is still "Job One" with these companies! At least they say it is...
@oceanmariner
29 күн бұрын
It looks like the base of a water turbine. If the bearings were out of alignment or the impeller out of balance, that could cause cracking and failure we can see.
@28704joe
24 күн бұрын
You know they do good work when they have a lose goat wandering around in the shop.
@Exnay777
19 күн бұрын
In-day pleasures...one of the perks in place of wages!
@gorillaau
15 күн бұрын
Every shop needs a safety officer. Some use a dog, this one has a goat.
@MrPierre4568
11 күн бұрын
These guys get more work done by accident than a lot I've seen get done on purpose.
@upsidediy3945
21 күн бұрын
Looks like a hydro generator part, but is a part casted onto a mold, to cast more. Or it has a thick frame /housing plate, to bolt to other parts.
@Mr1Blacktooth
27 күн бұрын
That's some seriously heavy duty shop equipment and some precision work but I was most impressed with was that machinist perched on that flange like a bird. It looks like he could have stood there and done the work but he chose to perch.
@ianmacpherson2409
11 күн бұрын
I commend the craftmanship and injenuity of the workers. Seems lack of safety shoes will be a forever problem. I noticed a large helical gear sitting in the dirt. I was taught to never get a precision `part get exposed to dirt. I know that the men use rags to clean parts with . Rags (especialy used ones ) just arent good enough in precisions work. Perhas as concrete floor is in the future.
@christianvalenzuela225
20 күн бұрын
Is an undevelopped country… they don’t have money enought…. They repair all……. Smart efforted workers, My support😊
@gorillaau
15 күн бұрын
In plenty of countries things are repaired. Common stuff such as a toaster, worth $20 new? Never. An arm from an earth mover, worth $20,000, currently not in stock with the OEM and not on backorder either. Oh, and will take weeks if not months to obtain fro the OEM. Definitely repaired. The object above looks like an expensive item. Definitely worth repairing an any country. The turbine or pull a, or whatever it is from is going to be locum, much more costly to replace. Let alone time to obtain the replacement unit.
@nicodesmidt4034
28 күн бұрын
35:20 sure, why secure the load to the truck ? The Thing weighs more than the truck 😂😂
@kwinterburn
14 күн бұрын
Being cast iron it would be difficult to repair , its a good repair , just the pins are in the water flow , suspect a newly cast one is in its future, if it was cast steel it could be welded , but it looks cast iron , a sparkle test woukd prove it
@Toqueville2023
14 күн бұрын
And how about the carrhart company uniforms..very practical looking!
@AffordBindEquipment
12 күн бұрын
gotta love the old repairs. And just bolt it together? no welding? How do they know it's flat on top? quick and cheap I guess.
@kwinterburn
14 күн бұрын
There will be a bit of obstruction and powerloss even cavitation , but it will function just fine
@rustyhebert1451
29 күн бұрын
Looks like directional vanes for a water turbine
@sidneybowerman558
16 күн бұрын
That is severely out of balance.
@bobengelhardt856
27 күн бұрын
"How We Repaired This Giant Thing ...". I wouldn't say that it was a "repair" at all! The number of bolts added were not nearly enough to take the loads that the broken flanges had carried. This must just be the 1st step - all those broken flanges were probably going to be welded while the added bolts held them aligned.
@casper8969
13 күн бұрын
It's a pedestal for a vertical pump or pump/turbine.
@waynethomas3638
24 күн бұрын
if you dont know what it is, how do you know what is damaged and then how to fix it?
@williamhoward8319
14 күн бұрын
looks like the base of a ramond mill used to grind stone we used7 of them for limestone
@martinburwell4214
13 күн бұрын
100% right ,worked on a few of them ,looks like a 50" dia 5 roller
@kwinterburn
14 күн бұрын
Thats a vortex ring ( guide) off a hydro turbine
@sidneybowerman558
16 күн бұрын
Why wait till the last moment (it was on the back of the vehicle) to drop in the remaining bolts, and then not add the nuts? I bet someone asked "did we make too many bolts n nuts".
@williamhoward8319
14 күн бұрын
is definatly base or a mill ours were made by c e ramond
@mfowelectro
17 күн бұрын
If you don't know what it is how can you be sure you fixed it?
@lookylook570
12 күн бұрын
Just a bit of runout on that drill press….
@nasserelhaqnsarellah6938
29 күн бұрын
Water turbin for poker generator
@darkwaters757
29 күн бұрын
Could it be the base of a vertical lathe?
@cpo415
14 күн бұрын
India is going to eat all of our lunches.
@derekb4731
28 күн бұрын
Love these videos, can you imagine health and safety lol
@FlyToChina0071
27 күн бұрын
As other have mentioned: Looks like the static part of a large pump / turbine... Regards from Denmark
@colinclenton7693
29 күн бұрын
Can I ask just what was the repair?
@lewiemcneely9143
29 күн бұрын
I still don't know what it is but it's had a LOT of wear on it. Good fix job though!
@user-or8ij9uy3k
25 күн бұрын
立派な修理工場出来たね‼️ Pit がないね ドリル作動には油を
@samueldamewood5273
26 күн бұрын
Base of a cone crushing mill. Ain't go no OSHA in Pakiland!
@edwardpedley8813
13 күн бұрын
I haven't seen all types of cone crushers but that's the first thing that came to mind when I saw it.
@robertmason8341
29 күн бұрын
Guide vane/wicket gate
@toddwheeler1526
29 күн бұрын
Large sewage macerator pump impeller.
@1SweetPete
29 күн бұрын
Makes sense
@toddwheeler1526
29 күн бұрын
@@1SweetPete I stand corrected, I believe it is a stationary "VOLUTE" for a macerator impeller. BOTTOM INTAKE. Big work there. I would guess 1000 - 1500 horse power. Love the classic old machinery and the "we can fix anything attitude and spirit " keep everyone safe, be well, prayers 🙏.
@nasserelhaqnsarellah6938
29 күн бұрын
Power
@MickMcMadder
27 күн бұрын
Link to the safety-sandals anyone?
@007mrdarcy
28 күн бұрын
CANT BELIEVE THESE GUYS ARE WORKING WITH FLIP FLOPS ON
@Gary-o1b
24 күн бұрын
You mean safety sandals!
@gorillaau
15 күн бұрын
You expect them to work without flip flops? Harsh. /s
@sba7336
13 күн бұрын
It's not a proper repair.
@FrankGarcia-tw9qz
12 күн бұрын
Will done 🎉
@shawbros
25 күн бұрын
It's a thingy.
@gorillaau
15 күн бұрын
Thingy is too small. This is a wodget, which is even bigger than a widget.
@wthorwirth
12 күн бұрын
Repair? LOL
@billwallace6066
17 күн бұрын
Occupational Health and Safety would have an absolute fit about these conditions, there are SO many things, wrong I doubt they would know where to begin!
@peterplouf2836
16 күн бұрын
I do. They would send everyone home, Nothing would ever get done and the people would live in a stone-age society.
Пікірлер: 86