Thank you for the video. Been researching this for a day and everyone else was using resistors across certain pins but yours was the easiest one and you explained it very well. Cheers!!
@DIYBill
7 жыл бұрын
Glad to be of help
@bojancurcic6249
7 жыл бұрын
Why people use resistor??? i have thi psu but 1200w and i dont know what to doing?
@someguyontheinternet-
4 жыл бұрын
Excellent video! Thanks for the info!
@nathanpennell2309
7 жыл бұрын
thanks man really helped me out.
@fpvupthere7611
5 жыл бұрын
Hi Billy & others! I am running a couple of HP proliant 380 units PL 18 for lipo chargers, very happy,But have a question about the fan. Mine is working, but seems to be a low speed, it seems to get warm but not increase speed. Do these have an internal temp sensor to increase fan speed or do I need to mod? Neal
@davidellenberger3852
4 жыл бұрын
Can you check if it operates also with DC voltage and what mi imal voltage is needed? I wonder if it could convert 48V battery to 12V in a solar application, thanks!
@bojancurcic6249
7 жыл бұрын
Hello, i saw some psu where put capacitator, transistor bla bla bla... is that necessary??? you are only connect 1 and 4 pin together, i plan to use switch on that two pins.
@geraldcmoi3775
3 жыл бұрын
Hi, for the benefit of others, i have a HSTNS-PL14 model and 1k resistor between 33 & 36 does not work, so i tried short-circuit between 33 & 36 and it's work perfectly!
@camilloiachetti8038
5 жыл бұрын
Sorry, can you tell me the contacts to short-circuit? give me a scheme Thank you so much Camillo
@bozorgi2
6 жыл бұрын
thank you billy , i have 1200w and i circulate pin 33 & 36 and output have 12volt but i want use it as for 4 GPU PCIe 8pin is that can work without problem ? because i see another hack of 1200w they say connect pin 33 and 36 with 220 ohm resistor another forum say use 550 ohm which way is better for GPU use? a lot of thanks
@DirtNerds
5 жыл бұрын
I have a control board that works and voltage adjust mod on the same board. has anybody figured out how to make them master and slave so you can use one voltage reference for adjustable voltage when using multiple power supplies?
@Barbiturickr
6 жыл бұрын
thank you !
@carlos_sacalul
3 жыл бұрын
Hello. please help me, I accidentally made contact between those small pins, the fan went into speed and from that moment even if I make contact between the first and fourth pin, I don't have 12v and the green LED doesn't light up anymore. Did I burn? Is there any chance it will work? thanks a lot
@EnnTomi1
6 жыл бұрын
good way to terminate those PCIe connectors?? how am i going to attach wire onto those gold plates? solder straight on?
@MxGRhythmlModsMusicGamingl
6 жыл бұрын
Liangshi Xu yup, or clamp it with electrical tape and clamp
@ankitkumarrathod4593
6 жыл бұрын
how can we get 12v from a hp printter's power supply but it does not have and 12v hub,etc
@ejgaming0161
Жыл бұрын
hello sir,i have 1200w 100A max hp power supply,just wanna ask if i done that trick can i charge my 22A Lifo4 battery pack?will the battery damage or someting,?thanks in advance!🙂
@pollydor07
7 жыл бұрын
Thanks
@ralph9987
4 жыл бұрын
i love tripods, so handy.
@trei2unu
7 жыл бұрын
hi, does the fan turn on only after a while with the load on? and when it does, it runs at high rpm or just as need respectively of the load amparage? thanks
@DIYBill
7 жыл бұрын
Alexandru Simonescu it run depending on the heat of the smps. The hotter it gets, the faster it runs
@LordLab
6 жыл бұрын
on how many % load it starting to spin ? this is 750w ? so maybe on 50% ? please let me know.
@sanjay.kandi5
4 жыл бұрын
Hi, how to trun on HSTNS-PL12
@gabsave
7 жыл бұрын
Curious to know what do you use this 12V supply for? Intended application?
@extremebassline7281
7 жыл бұрын
im gunna be using it to power a car amp
@DIYBill
7 жыл бұрын
Gab Save I use 12v for a lot of circuits. Even for charging lead acid batteries
@gabsave
7 жыл бұрын
Billy Carvalho Where can I see more your projects if it's posted online?
@dascomp51
7 жыл бұрын
Some people are using them to power 3d printers
@Electronieks
6 жыл бұрын
Gab Save 3d printer
@stereojos86
5 жыл бұрын
Hi I have a HSTNS-PL53 yo know how turn on?
@donnyknows6346
4 жыл бұрын
I have same power supply. It used to work, then after a week what it does, when plugged to the main, the green led is off, the fan works as normal, I get 12v for a second then 0 v
@msieirop
3 жыл бұрын
Did you fixed that, have same problem.
@kamrankhan-ok1ll
4 жыл бұрын
Assallam ul kum sir my name is kamran from pakistan karachi sir i m not english languge sir yor vedio very nice and halp full sir plz halp me for power supply thank you
@DIYBill
4 жыл бұрын
Hi Kamran. Thanks for WATCHING.
@Slic-Rock
3 жыл бұрын
Hi great job but here a challenge to you. Can you hack a hp-dps 750ab-3 to 14.6V?
@11evl1
3 жыл бұрын
kzitem.info/news/bejne/po-Prn16iopioX4
@PaulDelmelle
5 жыл бұрын
How to increase the voltage of HSTNS PL-18 to 13,8 V ? Please help
@DirtNerds
5 жыл бұрын
I have a control board that works and voltage adjust mod on the same board. has anybody figured out how to make them master and slave so you can use one voltage reference for adjustable voltage when using multiple power supplies?
@simranjeettoor3891
7 жыл бұрын
My power supply give me shock please help
@jhonnyreposas25
Жыл бұрын
Hello sir how to get 12volts this psu
@philipbalababa2927
5 жыл бұрын
Pls help.me man i dont have the 12 v, i did 1-4 connected, and i still havent 12, even the green.light Doesn't work...appreciate your words😁
@darckrel
6 жыл бұрын
Hello friend I want your help with my astec aa20790 I don't have idea how do turn this on. Your power supply is like a astec and I too put a resistor 4.7k (I see this in a pag chinnese) in 34-com and 31+12v_chrs but this doesn't turn on. Thanks.
@genoaninha
7 жыл бұрын
Billy Carvalho muito bom o seu vídeo meus parabéns, Gostaria de saber ser você pode dar uma ajuda, tenho uma fonte HSTNS-PD02 Modelo: HP DPS-700CB A e gostaria de sbar como ficaria nesse caso de fonte.
@jtsgarage2999
7 жыл бұрын
can you ajust the volts oon it up to 14volt
@DIYBill
7 жыл бұрын
moonshiner 773 yeah you can. There is a pot inside. But I don't suggest it.
@Jrami608
6 жыл бұрын
You can get close to 14v. If I remember correctly I got it to 13.2vdc by adjusting the pot inside.
@englishrupe01
5 жыл бұрын
Use a DC to DC converter instead
@wickedindian24
7 жыл бұрын
mine does not have the pins that you cut, how do I get 12v I shorted the first and forth but nothing
@wickedindian24
7 жыл бұрын
model number 506822-101
@englishrupe01
5 жыл бұрын
Try first and third instead
@Abi_hatesherself
2 жыл бұрын
how to make it 13.8v?
@DIYBill
2 жыл бұрын
There are some variable controls on the PCB but I would really not suggest working on these unless you are qualified professional
Пікірлер: 55