Great video! Just got a Huskyboy for my son. Do you have any suggestion on what to do with the rearbreak, tried tightening the wire both at the handle and reararm, but it still break very poorly.
@V4XEN
11 ай бұрын
Hi, Thanks! If you haven't already, I would start by pulling apart and scrubbing clean the brake shoes and drum with petrol or brake cleaner. Once they are dry, reassemble and if still not working right, try adjusting the rear arm a couple of teeth on the hub. This should help if your brake shoes are getting low and are running out of adjustment on your cables. Let me know how you get on!
@Joelbarne5
Ай бұрын
Struggling to find a piston kit for the s5 gs engine on AliExpress. Same piston as this with a extra hole on the intake
@Kohanuitohu
2 ай бұрын
Hey mate, what year would this bike be? They seemed to have a husky boy '99-02' model and then did they keep making it as a CH 50? are they are very reliable and sturdy bike built to last or more a temporary throw away? cheers
@Bwd69
2 жыл бұрын
Thanks for the vid mate. Which country are you from? I have the same compression tester and find it to be quite unreliable when screwed in, I always get a much higher reading with the rubber “push in” attachment.
@V4XEN
2 жыл бұрын
Hey, thanks for your comment. I've noticed the same thing. However, the compression was so low before the new piston and rings, that it didn't make much difference. 👍
@vanyadimitrova352
Жыл бұрын
Can you help me please? What is the oil capacity in the engine. 0.25l is set in the manual, no it does not take more than 0.16l. Do I have to tilt the bike to take the 0.25l. I am confused. Thanks!
@V4XEN
11 ай бұрын
Hi, interesting... I do recommend the user manual amount. However, you may need to drain the oil out then remove the side cover and check that it has all come out. Some time's the oil can turn into a jelly like goop and won't come out when drained. Let me know how you get on!
@jannik_8561
18 күн бұрын
@@V4XENhi, i also wanna da a oil change but i dont know where the Oil drain plug is to get the oil out and also, which new oil should i use for the husky?
@danielgarton9082
Жыл бұрын
Awesome video, did you have to do anything to the clutch on this bike? I think my husky 50 clutch might be slipping a little bit, where would you get parts like new clutch springs or gasket? Thanks
@V4XEN
Жыл бұрын
Thanks for watching. The parts I got were all found on AliExpress. I didn't need to do anything to this bikes clutch but did give it a look over and everything was ok.
@danielgarton9082
Жыл бұрын
@@V4XEN great thanks. I have a very sneaky feeling I have this exact bike from your video! Except the exhaust pipe tip looks a little different
@scroogehowsshehandle
Жыл бұрын
Love these little engines my son has the LX2 or LX3 I have all 3 top ends for the s5 only problem I’ve ran into is finding some small internal parts . Part reference # 68 is a small thrust washer and there is 4-5 of them and they are basically impossible to find due to the measurements bought two engines for 160$ through another you tuber . Sounds a lot better the 2nd time you put it all back together did you do a rebuild video on this engine?
@petersheridan4603
2 ай бұрын
What spark plug is in this plz
@V4XEN
21 күн бұрын
Hi i think it had a BR8ES witch is a bit hoter than the BR9ES that is the Equivalent to RN2C. Hope that helps.
@kyrelparker2328
Жыл бұрын
Do you have a link for that piston my friend?
@V4XEN
Жыл бұрын
Hi, here is the link for the exact piston I ordered. However, I would recommend checking your current pistons measurements to make sure it is the right fit 👍www.aliexpress.com/item/32828799812.html?spm=a2g0o.order_list.order_list_main.10.436d1802grKDld
Пікірлер: 17