562 is an excellent saw still have 3 of them. 2 of them are 2016’s bought new together and both have never been apart. They’ve cut ALOT of wood and been very reliable.
@ragercrepair9301
Жыл бұрын
She's got power that's for sure, but it does struggle a bit which is totally expected of a 60cc saw sporting a 36inch bar. Still impressive for stock! Would like to see a fully ported 562 wearing that outfit.
@smithtradfallning
Жыл бұрын
Crazy how well it pulled that and on it's first tank to boot.
@Brian2bears
Жыл бұрын
Mr. Boedy, I may have missed it, are you doing a re-boot on the Auto-tune and M-tronic saws before the cuts? I watched the STIHL MS 400 36"vid as well. While the process is somewhat different for both saws, the cut times might be different if the saws are tuned with the 36" bars "before" the timed cuts...just curious about your methodology....thank you sir...
@stannelson2582
Жыл бұрын
I only have a 460 but it became more fun when I went from 24 down to an 18 inch bar. That 562 might be scary fun with a 18 or 20 inch bar.
@frankchirico-lo4el
Жыл бұрын
Best thing to do I only run smaller bars on powered/pro saws Cuts beautifully
@iceman_fox1
Жыл бұрын
that's a badass chainsaw
@Powersawjunky
9 ай бұрын
My 7yo son is watching over my shoulder. He said haha he missed the cut! You are entertaining guys of all ages 😂
@BruceMyersLBZ
Жыл бұрын
Just got my brand new 562 back from top tier builder/ porter and yes it screams, but my stock 372 pulled 24" buried in red oak much better. Made a mistake trying to replace 372 w hopped up 562. Picked up new Dolkita 7900. WAY more saw than my 372 was, feels about the same weight/ handling wise. I dont miss my 372. 562 now fills my 60cc role EXTREMELY well!
@novicelumberjack
Жыл бұрын
Yeah, displacement is king.
@h.v.schainsawtrees4967
Жыл бұрын
I’d be careful with a new saw running a 36in bar gets way too hot on the crank bearings will burn it up quicker I’ve rand a 562for years felling timber loves a 24 no more
@dirtdarte
Жыл бұрын
Pretty impressive for a 60cc saw. Full comp chain? Looks that way. How's the oiling?
@Dolmar-Rick
Жыл бұрын
Doubt, that's a full house chain, probably a skip 0.50 gauge? Or 0.58?
@novicelumberjack
Жыл бұрын
Full comp, C83
@Dolmar-Rick
Жыл бұрын
@Novice Lumberjack fair play... better than thought you must have got a strong one, slightly impressed. Though that's. 0.50 gauge, we only tend to use long bars in that gauge for milling, I can't imagine continuous cuts with that bar on that saw, stratos tend to run hot and go slower after multiple cuts in big timber ..can't see that saw lasting that long or if chain goes dull ... lots of problems with those saws failing here with short bars🤷🏻♂️
@Orefamilylawncare
Жыл бұрын
It's funny to hear you say the 562 is "close" to the 400 that's awesome. Says alot really.
@1d1hamby
Жыл бұрын
Maybe one day you could tie strap a 10X10 bunch of 4X4s together and do a time comparison of at least three cuts for each of the three saws with the same bar and chain swapped out? That's the way redbull661 channel used to check their setups.
@matticus6339
Жыл бұрын
Very impressive 60cc saw. I have been wanting a 562. I have NO idea why. I am a firewood cutter, My 2 main saws are a Makita 7901 which I keep a 22" bar on, my other main saw is my 390XP which usually has a 28 on and also I have a 36 for. WHY do I want another saw when I already have like 10 or more? I don't know, Chainsaw addiction for sure.
@matticus6339
Жыл бұрын
Oh I also keep a Husqvarna 450(yeah I know), that I keep a 16" on for clearing ATV trails, I been thinking of getting a 550XP to replace it but WHY??? The 450 does fine for what I use it for, always starts but why do I want a 550 and 562, I can;t justify it at all but I sure want.
@jjm3254
Жыл бұрын
Oh man, I felt for you when it broke through. Sometimes I cut with a hand bow saw and end up 30 degrees off vertical.
@dominicteresi3835
Жыл бұрын
Could you make another cut with both in the new size log
@robert4027
Жыл бұрын
I like my little Echo cs590. However I really want an angry husky thank you for the video
@Szczyrczek
Жыл бұрын
You finally did it, thanks! Definitely gonna buy it in the future. You could give a try of that HTSS(Walt/afleetcommand) bulit, so setting the squish right about 20 thousand, MM and that pop up piston, because everyone one can do these simple stuff at home, and then port it that would be awesome comparison. And since You going to port it You will be doing the squish and MM anyway so not that extra time anyway. Greetings Kuba
@novicelumberjack
Жыл бұрын
I'll be diving deep into this thing. But it takes me time. I'm slow.
@Szczyrczek
Жыл бұрын
@@novicelumberjack I get that, thank You for Your work and time Boedy!
@ohsnap46841
Жыл бұрын
I’ve got a pop up in mine, dual exhaust muffler mod, gasket delete, ported and a 20” Tsumura with husky full skip chain.
@Szczyrczek
Жыл бұрын
@@ohsnap46841 May I know why do You use full skip? How do You like 562xp? Whobdid port job for You!
@ohsnap46841
Жыл бұрын
@@Szczyrczek well we have a lot of pine down here in Louisiana and to me it’s like a hot knife through butter even on hardwood with that saw. My tach I have on it is close to 17k RPM. The porting, gutting the stock muffler/dual outlet was done by me and the pop up piston I bought from lil red barn. It’s a screamer lol. I’d like to put it up against Cajuns 562 which is a hell of a screamer just to see how I compare.
@cisco5400
Жыл бұрын
Well done! I prefer not for rpm go down so much, the saw struggles an might not be able to keep on going for as long as you like. Just my oppinion, thx 😊👍
@hrentr
Жыл бұрын
The 562xp will improve after about 5 more tanks.
@danagordon8871
Жыл бұрын
Hey Nov, question: I’ve got an old Sears PS 3.7hp (60.6cc). Based on what the 372 just did, shouldn’t my old saw pull a 36 inch bar?
@billyb.9878
Жыл бұрын
So the 562 xp is a large mount bar, how did it oil?
@novicelumberjack
Жыл бұрын
Seemed to do perfectly fine. The bar didn't get burnt up at the bottom. I had the oiler turned all the way up.
@ebenez88
Жыл бұрын
Hi Mr Novice, I just want to know Stihl vs Husqvarna which one is better chainsaw, because im looking to buy chainsaw this summer Thanks
@mattfleming86
Жыл бұрын
They (and echo) all make great saws. I'd start with stating how big of a chainsaw you need, what kind and size wood you will be cutting.
@austindenotter19
Жыл бұрын
Dealer support also critical.
@TJussilainen
Жыл бұрын
there is some newer 562 come with dished piston.
@bethanyhaskiell9116
Жыл бұрын
All the 562 saws ive had the pistons were domed pistons the only things that changed were the carbs
@ohsnap46841
Жыл бұрын
My stock 562 piston was a flat top.
@Brian2bears
Жыл бұрын
@T. Jussilainen, you are very correct sir and know HUSQVARNA well..
@patrickpoulard24
Жыл бұрын
Husqvarna is the JV and Stihl is the Varsity. That is just the way it is and that is the way it's going to be. What more could I possibly say, STIHL RUNS THE YARD. 😊👍🏿👑👑👑👑👑👑👑💪🏿 #stihlpower #stihlisyourdaddy #stihlrunstheyard
@novicelumberjack
Жыл бұрын
Ya know...I am growing to like your little rants. Seriously. I am smiling from ear to ear right now! 😃 😊 🙂 😀 😄
@patrickpoulard24
Жыл бұрын
@@novicelumberjack I'm glad that you are smiling. You should see the smile on my face when I'm using the Gold standard in chainsaws Stihl. Especially when I'm using the 500i. It's good to be the King. STIHL RUNS THE YARD. 😊👍🏿👑👑👑👑👑👑 #stihlpower #stihlisyourdaddy #stihlrunstheyard 😊😊😊😊😊😊😊😊😊😊
@buddysumner4022
Жыл бұрын
And you are a brainwashed dipshit,
@poparamiro
Жыл бұрын
Awesome video! Best regards!
@crusiethmaximuss
Жыл бұрын
Y'know, I haven't ever seen anyone put a mini turbo on a chainsaw before... Hmm...
@prestontimbs74
Жыл бұрын
It just looks better too Bro Namath.
@aaronpowell4885
Жыл бұрын
What a beast for stock!
@novicelumberjack
Жыл бұрын
Yeah man, I am totally impressed.
@shawnglacken3055
Жыл бұрын
Great vid. Keep it up.
@masonmcqueen5059
Жыл бұрын
Hard to compare to the echo 590/620, they are made more for torque, 562 higher hp & rpm, I run both, killer saw but has its place for sure
@paultrummer7289
Жыл бұрын
That's a stout saw for being that size I'm fixing to take my 372 get some fire wood trying out a new chain it's a orgeon skip tooth square ground chain see how it does to my hand filed square keep up the good videos
@Sethhaun78
Жыл бұрын
67cc vs 59 cc why..folks and comparisons should only be done stock no saw is modified the same.
@j.c.lawntreesnow6272
Жыл бұрын
After the muff mod and break in its going to eat that still 400
@cajun3197
Жыл бұрын
Yep absolutely will
@Doc-Cole_Trickle-of-Chainsaws
Жыл бұрын
👍🆙BigGuy
@appalachian8999
10 ай бұрын
Just because it can pull a 36 inch bar doesn’t mean you should.
@crazyfeller5704
Жыл бұрын
👍👍
@TDC-ih8ct
Жыл бұрын
Way to make a saw cry. ???
@troybeans34
Жыл бұрын
They pull all day at 24 but I found myself using 20 and 18
@prestontimbs74
Жыл бұрын
DAYYYUMM! I gta get one...
@darrenwilson7688
Жыл бұрын
Mean saw, makes me wanna trade up!
@EcSsAwS
Жыл бұрын
Ehhhh now ya lost me Boedy. I done had a modded 562 and it wanted no real part of a 36” bar Ya lost me bud
@novicelumberjack
Жыл бұрын
Whatya mean? I simply put the bar on and cut a chunk of wood. Where did I lose you?
@cajun3197
Жыл бұрын
How was it modded? If you did a base gasket delete and raised the exhaust with some hogged lowers it would lose power. Sometimes,”modded”. Is less power if it was done in a certain fashion
@Szczyrczek
Жыл бұрын
@Cajun Hello I have seen some of Your amazing work. If I may ask, Is BGD, MM, and pop-up piston gut idea for a bit more grunt?
Пікірлер: 86