Your video helped me out a whole lot I like your video
@nelsonmsn110
6 жыл бұрын
Sir I just wanted to say I am NOT mechanically inclined. My drive belt broke on my mower and I watched your video and changed it with no problem. Saved me a ton of money taking it to a shop. Thank you.
@davidwaddell5441
2 жыл бұрын
God damn finally somebody put a detailed video of how to replace the hydro belt instead of wham bam there it is. Thank you so much. The wire had me cursing a blue streak.
@lgale5623
7 жыл бұрын
Thanks for the video. I just did this job today. I used a paint stirring stick to push the belts above the drive motor pulleys. It's soft enough not to cut the belt, and it bends enough to get over the pulleys.
@rexyoshimoto4278
Жыл бұрын
That's a very tough look under the Raptor.
@thomasmcray8195
4 жыл бұрын
I removed everything you said, and followed you're advice. 25 minutes and up and running. Not sure why the old and negative comments. Anyway thanks a bunch.👍
@WilliamHollinger2019
5 жыл бұрын
You are making more work than need to I replace the drive belt with strength and needle pliers and feel with hands
@aftermathexperts3068
5 жыл бұрын
do tell. Id like to do it with strength and needle pliers as well. Please share method, thanks
@tommyjackson7323
6 жыл бұрын
Turn belt sideways to get it on the transaxle pulley it's a tight fit. Fan can cause belt throwing problem count on it
@code23hyper44
6 жыл бұрын
Tommy Jackson fan? Can you explain? Mine drops a belt whenever I lower the deck before running the blades. Makes me insane.
@tommyjackson7323
6 жыл бұрын
Ducati Hyper821 drive belt or deck belt
@gman922
7 жыл бұрын
I found 2 nuts and a mounting bolt missing from the transmission! I was lucky it did not fall off the machine. Have replaced all the hardware bolts, installed nylock nuts and spring washers.
@ShaneSimon3D
5 жыл бұрын
Thanks for the great info - very helpful!
@byroncouch5895
8 жыл бұрын
Thanks for the video. Just changed mine last night after watching. My drive belt came off and then broke as a result of the fan fins above the pumps being bent up and interfering with the belt. I assume a stick was thrown up there and messed up some of the fins. I heated up each fin with a heat gun and bent the fins back down before putting the new belt on. Worked like a charm.
@Randyragee
8 жыл бұрын
with the new drive belt the hustler probable run like new again 7mph
@hellspite
7 жыл бұрын
If the front of the Hustler 42" Raptor is lifted up as high as it will safely go...... is there enough clearance to change the drive belt? Instead of faffing around under the back of the mower on the ground?
@anthonyguerrero4915
6 жыл бұрын
trying to replace drive belt ( hustler 54") belts break or come off pulleys then you try to drive foreword . fans are not touching . any ideas ?
@anthonyguerrero4915
6 жыл бұрын
found two broken bolts on the cross member that from gear box to gear box .
@eazye4you
2 жыл бұрын
This is the deck belt, not the drive belt
@phourtwenteephorlife
2 жыл бұрын
What size is the belt boss ?
@livingsimpl3
4 жыл бұрын
what is the part number,or where did you get this replacement
@snoopfurlow1275
4 жыл бұрын
Check your local napa dealer have them to match up the belt,i had the same problem, they matched it up,i think its a 50x 1/2,they measure it,was rolling the same day
@hellspite
7 жыл бұрын
changed the belt went 10 yards the belt came off! think one or more of the pulley fins is bent and hits the belt, so now I have to figure out how to change both pulleys on top of the transmission
@PappaDanTrucking
7 жыл бұрын
had the same thing happen to me I found that the hydro unit had a bolt missing that caused the unit to drop and so everything was out of alignment after i replaced the missing bolt and nut everything worked great
@gman922
7 жыл бұрын
Yup just replied
@johnbgator
5 жыл бұрын
try a mower shop keep the small man working mistakes could cost ya being cheap in the long run
@PappaDanTrucking
7 жыл бұрын
you can doe this with out dropping the deck belt you just need to feed the new belt around the inside of deck belt by hand and then it will be above the deck belt i did this because i did not want to deal with the deck belt
@michaelpuckett1480
6 жыл бұрын
dan did not happen the drive belt has to be around the top v pulley
@KWaters
6 жыл бұрын
Excellent how to Video. I just bought a used (29.0 hrs) raptor at a local dealer and in less than 3 hrs use has blown the belt twice. There is something seriously flawed about this design.
@johnbgator
5 жыл бұрын
you guess its the clutch ??? keep the small guys employed one wrong move cost ya hundreds
Пікірлер: 31