Thanks to you I was able to get my HY 110v VFD up and running.
@alexsabillon6794
4 ай бұрын
Tigre gran maestro veo que conecto el VFD sin mucho cuento y la configuración quedo cheque solo una pregunta, donde se conecta la bomba de agua en el VFD AYUDENE PORFAVOR...
@ndoghouse6853
2 жыл бұрын
Do these vfd's usually have DC voltage outputs for controlling other devices? I have another chinese VFD that has terminal marked 24v but dont know if its output or input for something? Guess I could plug it in and see? That would be nice for powering my mach3 usb breakout board. Im inclined to use separate power supply for breakout board for noise considerations anyway so it may not matter?
@BillyWaggs4052
6 жыл бұрын
I bought this same unit with a 2.2kw Water Cooled Spindle but out of the box I have had nothing but issues with it. I get an "Er 04" Error and all options to change parameters is locked out. Seller cannot tell me whats happening nor can anyone on any forum. Can you tell me what is going on with this unit to get such an error...? I have since gone to a different unit but would still like to get this one running somehow....
@h3ndesenvolvimentos
6 жыл бұрын
Can you Solvet this problem? I have the same problem...!
@BillyWaggs4052
6 жыл бұрын
Eng. Bruno Ponces, I ended up purchasing another unit that was better supported by youtube posts and online documentation. However, let me dig out this unit and try something I was told would work. I believe what has happened in my case was I was following the direction of someone in a KZitem video and unknowingly locked out the controller due to the instructions NOT being the same as those I was following in the video. i will report back shortly. please be patient as I am super busy this time of year. But I will give the fix a try and report back.
@hugojavierfigueroa5819
4 жыл бұрын
Hi Billy, did you solve the lock on the frequency converter?
@amosdevonish5767
3 жыл бұрын
Can the spindle cables and ac power cables share ground on the vfd?
@briansmith7015
8 жыл бұрын
You really should connect the SAFETY earth to your spindle case irrespective of whether the gantry is earthed or not. You have a metal case, water and high voltage so you have the risk of electric shock and potential RF interference issues. You should, ideally, use screened cable from the drive to the spindle. I have seen and felt what happens when things go "live". Be careful, Brian.
@MrFastFarmer
7 жыл бұрын
WTF... Mate this is China.
@ChimeraActual
6 жыл бұрын
The #4 pin on the motor plug is for earth, Siamese with power source earth at VFD.
@Tinkersmiths
5 жыл бұрын
Brian Smith Most of the time the CNC Frame is already grounded. So connecting the spindle ground will cause a ground loop which will burn up the CNC spindle. It’s fairly standard practice to leave pin 4 not connected for a 3 phase system.
@RubensCampello
2 жыл бұрын
@@Tinkersmiths Friend explain it to me better please this loop mentioned, grounding is not all one?
@Dynoworksperformance
Жыл бұрын
What wires go where? Does U go to 1. V go to 2. W go to 3. ???
@plasticbaldy
8 жыл бұрын
Currently my 240V power shuts down at the end of repetitive cycles and restarts when I click 'Cycle Start ' on my Mach 3. If I only connect the motor wires and these interrupted 240V power wires will I have to reset the speed etc on this VFD on every cycle ?
@juniorlira1304
7 жыл бұрын
obrigado pelas dicas amigo .
@joeygonzo
Жыл бұрын
did not show which is UVW to what number
@blackpaz9949
5 жыл бұрын
Gracias o thanks
@jasepotts2865
6 жыл бұрын
I have one of these that suddenly after 5 months says E.Lu.5 and refuses to get passed this error. I've checked all wiring and it is still ok...any ideas?
@hamzahk.8721
7 жыл бұрын
this was very emotional
@zx001961
5 жыл бұрын
will R&S work
@plasticbaldy
8 жыл бұрын
You rushed through the critical description of the 220V connection. I had to look elsewhere to understand this. Most amateurs are familiar with Active, Neutral and Earth wiring. This is different. Please don't reply with "This tutorial isn't for amateurs" because an electronics expert doesn't need this video.
@bojansar1
6 жыл бұрын
Liberty Warrior The Earth pin is not connected to anything,should we additionaly solder a wire to the spindle body ?
@hardsofthx
6 жыл бұрын
Liberty Warrior Hi Excuse me, you know how to connect in a Mexico connection where there is 110v @ 60hz
@cnccarving
5 жыл бұрын
@@hardsofthx you need 2 live wire on R S T is neutral and use a ground rod or dig in ground larger iron do not share the neutral and ground because it kills the vfd
@plasticbaldy
8 жыл бұрын
Why did you change PD5 and PD4 to 400 Hz ? Is factory Default 50 incorrect for this motor ? What effect does changing this value of PD 4 & 5 have ?
@robert5
6 жыл бұрын
It is a 400 Hz capable spindle motor and is a high speed unit, this is why it is rated for 400 Hz and thus requires a setting of 400 Hz.
Пікірлер: 29