I took a used air chisel bit and cut a groove in the center. Then with air chisel I popped the rod out same as using a pickle fork. Worked like a charm. Food for thought and saves welding. If you do this again that’s my input but the rest of you vid is spot on.😊
@ADIYHD
Жыл бұрын
THANK YOU! My 79 step van hydroboost has been leaking for a while now. I never thought to cut the pivot off and weld it back on. No other video changes those smaller seals.
@MrRv8pilot
Жыл бұрын
Thinking outside the box. Glade to help!
@scottm7341
Жыл бұрын
The machined spacer to spread the seal was the tip I have been looking for. Watched many vids where they just force the piston in. Thanks!
@zacharylafata5142
Жыл бұрын
You're the only person aside from me who has changed the rear 2 seals. Congrats! Love the 4bt swap.
@MrRv8pilot
Жыл бұрын
Thanks brother!
@mayken6661
Жыл бұрын
Damn, how’d it go? I’m really considering just buying a new one, But if I can save $2-300 why not !
@yostusoda
9 ай бұрын
That inner piston needs pressed down on that spring while it's in the housing then the c clip can be removed then the shaft comes out. It is assembled with the new seals from the outside while being pressed back in. Kinda hard to explain. Press on the big cup piston so the spring and shaft pop out of the housing enough to get to the clip.
@MrRv8pilot
9 ай бұрын
Interesting, I don’t remember seeing a C clip. How would you push the piston down while it’s in the housing. Have you rebuilt one before?
@mohamedfingerprint
6 ай бұрын
More details please
@bondvagabond42
Жыл бұрын
I ended up chopping and welding mine too, on a 2000 f550, I saw a nice writeup on line where the guy just levered it and it straightened out the 3 swedges, but when I tried it, I bent a tire iron, hah, so with that much force I figured welding was safer.
@mudslide4x1
20 күн бұрын
Thx for the vidio But hate to say you can stretch the seal over the pin area on rod to pedal and pull through bore and get it on the piston Just did it no welding . used wire with a hook pulled through Thx Dean You have to do theses seals no vidios do
@MrRv8pilot
20 күн бұрын
That sounds like a better work around then cutting the input rod, pigpilot commented that with brute force you can separate the two. Maybe someone needs to design a puller.
@manuelanaya5763
Жыл бұрын
se tiene que utilizar un extractor para sacar el embolo del piston,con esto evitas cortar.....saludos desde mexico
@MrRv8pilot
Жыл бұрын
That information would have been helpful before I started😀
@emiliogarciasantos7159
Жыл бұрын
Buenas noches que tipo de estractor se usa para no cortar
@emiliogarciasantos7159
Жыл бұрын
Ayudaaaaaa voy a reparar el mio
@horacioguevara1845
7 ай бұрын
Explica cómo
@pigpilot7275
Ай бұрын
The pedal rod is held in by a rubber ring. Brute force to pull it out.
@MrRv8pilot
Ай бұрын
That’s good info, a little late but good to know 😊 thanks
@pigpilot7275
Ай бұрын
@@MrRv8pilot Wish I could have gotten the info out here sooner, but mine just came out of my van a few days ago. Waiting on the rebuild kit. This is probably my 20th video on the subject.
@dixiemae5042
2 жыл бұрын
First 🎉👊🏻💪🏻
@JustinDegreenia
4 ай бұрын
About the machined block you made to install that piston, can you make me one? That thing is fantastic! If thats something that can be done, let me know. Thanks!
@MrRv8pilot
4 ай бұрын
Let me look to see if I can find mine and if the your is the same I will send it to you
@JustinDegreenia
4 ай бұрын
You're the best thank you
@14freeland
Жыл бұрын
first
@richardamaro5722
7 ай бұрын
Not everyone has a machine shop at home, nor did you finish the job.
@MrRv8pilot
7 ай бұрын
Whats your point? Nobody forced you to watch my video. I post to help others if it doesn’t help you then move on!
Пікірлер: 28