Hello Tinman! I have to give a story. I have a 545 Mark ii and a 562XP Mark i. I loved my 545 so much and really became interested in the 562XP. I remember reading and seeing some bad things about them. I got kinda nervous about them but I kept searching. In fact, I even saw your video showing this saw and you telling a similar story as you did in this video. I remember it starting easily for you and you were going to keep running it even though it was a bit ragged. So I bought one about 1 year ago. I LOVE IT! That has to be stated. I have documented this full well. I have been transparent and have ZERO agenda against the brand. My saw is in the shop once again. In 1 year it has spent weeks in the shop. They have replaced parts, they have done leakdown tests and are doing them again. The saw is showing 9 hrs on the computer. It has more because I believe when they replaced the carb, the hour meter was reset. I do however think it has less than 20. Many people may have seen what I have going on. The big thing for me is that while I always take more than 1 saw, this 562XP leaves me no choice but to bring another. It ran perfectly well for months then failed again. I may have just gotten a saw with an intermittent gremlin...... and I understand that. Another channel had a 562XP purchased the same time as mine and his coil failed immediately. He uses and loves his 545 and 550XP. They have been flawless for him. His 400c and 500i have been good. He like me, regrets the 562XP purchase. It is simply my favorite saw to run due to how smooth and powerful it is, but has proven to not be a good saw for me. That is just my experience. Keep up the good work Tinman! I will say this..... my ECHO CS-620PW has run perfectly but also had a oil pump failure but the 562XP is quicker and nicer to run. All of this is documented in real time on my side. Thank you again
@aaronpowell4885
5 ай бұрын
Was just wondering if you watched any of the Tinman's content while watching this one! Sad how Husqvarna seems to have taken a few steps backward, with regard to reliability of the 562's.
@oakiewoodsman
5 ай бұрын
@@aaronpowell4885 I certainly had. You know me AP. I am the type of person that REALLY researches deeply and agonizes about this stuff. Honestly, when I bought my 620, the 562 is what I wanted first. So much so that I went and bought the 562 later just cause I couldn't get it out of my mind. My 545 has been so good that every time I ran it I thought to myself, what is the 60CC 562 like if this 545 runs like this. Again, I think you can attest, I have tried to be very fair about the situation but it is certainly frustrating. Thank you AP.
@sawmanbigtreeslayer2360
5 ай бұрын
I have never owned a 562XP. Always heard and seen bad things. 😢😢😢😢😢
@barrychouinard4019
5 ай бұрын
Recently added the older little brother to the 562 to the stable. A 261. I like the old stuff. It's actually pretty amazing how much remains either unchanged, or slightly modified. Seems to be a good saw so far.
@metsamikko
5 ай бұрын
I have 560xpg from 2012 and had no issues what so ever. Reliable and good power. Few years ago went on a dealer and they look up the data from Autotune,everything ok and total running time was 623hrs. Now its about 800 and saw is running good.
@anemone104
5 ай бұрын
Interesting. Thanks for posting and showing that cylinder and piston. Only worked on two 550s, both thrashed with dull chains and both nipped up. Rebuilt one with new ring and cleaned up cylinder and piston and it did another six months before it was blown big time. Same issue. Dull chains kill saws. Harder on these 5 series rev junkies.
@Husky455fan
Ай бұрын
Looking forward to seeing the 500 series build! So many of these new saws are strato charged and I would love to hear your thoughts on porting them. Thanks for all your work.
@BigKidCasey
5 ай бұрын
Your shelf is getting too full. Need to do some saw giveaways... for safety.
@wrstew1272
5 ай бұрын
I will reluctantly agree….need an address 😂?😊
@sawmanbigtreeslayer2360
5 ай бұрын
😂😂😂😂
@jamesmooney5348
5 ай бұрын
Right on Tinman, right on! Hope your baby and wife are wel!
@nickbanks2873
5 ай бұрын
My first saw I rebuilt was a blown up 562xp that I picked up for $100.00 I put an OEM top end kit on it and it runs great , that opened the door so I had to big bore kit my 372xp and that saw is a beast I still have my toy saw 460 rancher and a 365 x-torq
@brucenicov1224
5 ай бұрын
Nice!! That’s definitely going to be your go to saw once you git’r done!! Other than fuel and oil, sharpening the chain, you don’t need to fiddle with it. Makes the job easier.
@jamiedalluge9472
5 ай бұрын
The new 562 mark 2 are really nice. We have ported and sold 10 -12 since the first week of Dec with great results
@Daltargames
5 ай бұрын
I just got one last month because bucking billy was making a ton of videos about it and said it was great and it’s quickly became my favorite saw I don’t have a ton but I like it better then my 390 I wish I would have gotten all 5 series saws
@cheba4786
5 ай бұрын
У Билли 562 mk2
@leonardryan8723
5 ай бұрын
Tin man you will have rebuilt again buddy great video 😊.
@ibbylancaster8981
3 ай бұрын
It’s guys like you and Buckin that have gotten me way deeper down the rabbit hole. I bought a 585 last year and a 562 Mk2 about a month ago. I have an old 51 that was old when I bought it and it will still run like a scalded dog 16 years going. I run nothing but 40:1 non ethanol gas in all my saws and have for years. Piston in that old 51 still shines like a diamond in a goats A$$. 🤣😂. Still working on my second tank of fuel on that 62. Wanting to build a pipe for one or the other or both I have plenty of stainless tubing in various sizes. I also have access to a milling machine to make exhaust plates that I can weld to. What size and length would you suggest without having to go and rejet it.? Sorry for the long winded comment. Much love to you from North Carolina and be careful out there.
@G-PA-2795
5 ай бұрын
My 2014 spent its first 2 years cutting utility poles. A lot of cutting in the dirt and hitting nails is a thing. Then i retired it to firewood duties. Never had a single failure.
@Ecthelion_2nd
5 ай бұрын
Great video as usual.
@tinmanssaws
5 ай бұрын
Thanks
@alessandromonizza8283
5 ай бұрын
That junk cylinder might come to a new life with some Dyno joe mods cast iron sleeve work. Also would be quite interesting, to see how it could go with that and maybe port it.
@magnaira5072
5 ай бұрын
Weve been running opti fuel mix in our 1984 266xp since it was new. Never had carbon build up issues.
@larrywarner9314
5 ай бұрын
Tinman that's a true testament of how Husqvarna saws are tuff, I put a 2171 together with part's from a couple different saws to make a good one for my firewood buisness and the cylinder wasn't perfect had some scoring I couldn't clean up , but it runs great and I just pulled it down and other than that spot in the cylinder still in good condition,
@tinmanssaws
5 ай бұрын
I figured this one would of blown up years ago but she kept running.
@tdawg8605
5 ай бұрын
Interesting saw but I more interested in the older huskies but this will be good content for sure. TC Mahalo Tinman 🤙🤙🤙
@curtisbaker5407
5 ай бұрын
I agree...in fact...this is gonna be my next saw!...people listen to EVERYBODY on here yacking about this or that...but I'm a stand alone type of guy that HAS to have my own experiences. I was debating between the MS 400 or 562..but the 562 to me is just "sexier" plus I wanna prove that it can pull a 28"!! SHARP CHAIN is a MUST on ALL MY SAWS AND I've been running Opti-2 for years here too! So preciate the info! DEFINITELY helped me settle on my next cutter!
@k3vvv508
5 ай бұрын
If this saw will run, it is an awesome piece. But however they sadly fail really often, even If you buy this new from Husky. Also Heat is an big problem on these, go to get this muffler modded💪 Go for it, but that saw could cost a lot of money in the future 😬😬at least the MK 1 560/562
@richardhughes5638
3 ай бұрын
I loved mine had no problems with it
@lungocannone
5 ай бұрын
I had a 2012 model brand new, I was working in Switzerland alps, was very strong, same amount of work of a Stihl 440. was strong and I liked it. unfortunately I broked almost everything..always a problem. once carburetor, once recoil, once Carter leaking air.. they were a formula one in a rally competition..
@DOGMIHOLE
5 ай бұрын
Greetings from Poland 🇵🇱
@KCamp0506
5 ай бұрын
Wicked just starting and I've been hoping yahs get into a 562 TinMan 🧨 looking forward to this show
@aaronpowell4885
5 ай бұрын
Pretty incredible, just how much damage a 2 stroke can withstand and still run well.
@RyanSilva-ok1zg
5 ай бұрын
Could you take your saw to a shop to find out how many hours are on it with the old piston thanks for the content
@daryn_Canada_1066
5 ай бұрын
Great video, you fear nothing on the saw. Do you ever check the compression (with a compression tool) before and or after you do your repairs? I use them on my outboards but have never checked my saws.
@billyb.9878
5 ай бұрын
Wow, you & the bucking running the same saw. He's giving 1 away this Sunday. His got a pipe w/32 bar & a full skip chain. His is Gen 2, is this a collaboration or a coincidence. Only you 2 know. 😎
@curtisgriffith9825
5 ай бұрын
Yaaaayyyy! New video!
@craigwebber1311
5 ай бұрын
I'm a stihl guy buymt have to say I love my 572 alto tune
@patrickvennard838
5 ай бұрын
I am thinking of retiring my 357 and getting a MKII 562, I think they are good saw and deserve the bad press.
@mikecook2714
5 ай бұрын
I love my 562, I will grab it more then my 572 !
@Anders_HeymSR30
5 ай бұрын
They are built tough!
@RyanToomuchy
4 ай бұрын
Hello tinman and friends,. The 562 along with the autotune/5 series saws are very confusing/contruvervial.....and i keep a very open mind when it comes down to brand/product quality. This 562 is nasty, it boils down to not running ethanol along with low grade oil.....thas a whole nother rabbit hole!! But for me, ive only ever ran non eth fuel an husky oil, and opened the muff along the same lines you have.......wow, all i can saw is wow, its a saw to wtite home about, at 13,500 rippers, thers no room for h20 contamination, its a good note for Husqvarna to end their combustion chamber chapter on, and im a o44, 360 fan..so i feel its a very non brand fav, biased opinion? IMHO, thank you again, good day!!
@clydeb8865
5 ай бұрын
Not sure if you read comments, I picked up a saw today ,like new ..440e .he ran it with a loose plug.messed up the threads.i use my tools hard and depend on them ,so I go over them often..I respect your advice..can I repair the threads or should I replace the cylinder..the piston is like new.
@tinmanssaws
5 ай бұрын
You can buy a sparkplug thread insert kit to repair that. They work pretty good.
@clydeb8865
5 ай бұрын
Is it a helicoil?I thought about that...
@jamesmitchell5667
5 ай бұрын
I just bought two 272 Husqvarna‘s was just wondering what they are worth both run good
@kevinbeach2383
5 ай бұрын
Thanks for telling us about the mods and issues and how to fix them. Have you ever ported a Yamaha yz125 cylinder ?
@tomintexas817
5 ай бұрын
That's John at John's custom saws.
@michaellong9736
5 ай бұрын
Tinman, are you still looking for the intake nylon piece for that 394, and some parts for your 385? I just bought a lot of 12 saws, and might have some spare parts. ;)
@martyrutter3630
5 ай бұрын
The Tinman can do it all. Nice rebuild video. 👍👍
@jonathanhall136
5 ай бұрын
Shows you keep a sharp chain or she would have popped a while ago.👍
@chadaccettura1993
5 ай бұрын
I don't know about you husky fellas? For a 10-year-old saw that wasn't that impressive to me. I have to admit I am a Stihl man myself but I do have one husky. It's 20 years older than that saw and it is a 288 XP that was commercially used and I would be disappointed if it had that much wear on it. Great videos though, thanks tinman! 👍
@wykydkyd2
5 ай бұрын
@tinman would you please do a step by step video on how to take apart and replace an oil pump and worm gear and parts on a 268 Husqvarna thank you it would be appreciated and helpful ive aquired one that was taken apart and i am not sure how to re assemble it properly !
@tinmanssaws
5 ай бұрын
Pretty sure there's a video in my 200 series playlist cover that.
@rydplrs71
5 ай бұрын
Even if a filter does collect fines, that just means it’s working.
@sawmanbigtreeslayer2360
5 ай бұрын
Can you do an updated cart wheel for us?❤❤❤❤
@scottfoster2487
5 ай бұрын
I am suprised the newer 562 saws come with out decomp option, I plug every saw with them from factory .. Thes 562 saw with a sharp chain are dam mean , Not really much mods can be down to gain hp myou may gain some torque. These saw really are limited in improvement.
@BourbonDrinker
5 ай бұрын
I am sure you get this request all the time, but I was just asked by a friend if he could borrow my saw. I have used a saw since I was 14 and I logged in Vermont for a Summer. I worry about lending my saw to someone not experienced. What do you say when you think they could hurt themselves? Forgot to mention that this guy is my boss.
@tinmanssaws
5 ай бұрын
Just say no. Honesty is always the best way to approach any scenario.
@chrishoward1518
5 ай бұрын
❤❤
@tomintexas817
5 ай бұрын
Tinman I got something for you. I'll emails you later. Thanks saw guy
@michaelwhiteoldtimer7648
5 ай бұрын
If it’s on the internet it must be true 😅😅
@diggindiggenit6540
5 ай бұрын
That saw makes you look little when sitting behind it but i know your a big guy
@stevenlaxton3618
5 ай бұрын
Anyone on here have an opinion on the 562 vs the 565? Been using a 565 at work this winter and like it. My dad’s been looking to buy a bigger saw again and I’m thinking about trying to sell him on one of these two options.
@dgoodman1484
5 ай бұрын
565 is a detuned 572. Think of it as a heavier in weight but heavy duty 562
@G.A.gigger
5 ай бұрын
Wow ,sure glad you know what goes where with that thing ,or do you? I honestly would be lost ..ker shlang ,that would be it for 1 562. I want to watch to see how it runs after you put it back together ..I think Buckin got the Mark 2 didn’t he? I know he loves it..reason i ask is I am a Husqvarna guy and have a 372 and a 572 . My 572 is missing a bit and she runs so hot sometimes I don’t even run full throttle . I had the same anti vibe spring go on my 572 as on your 562 besides that it has never been in the shop ..this time I think I will get it plugged in because I wouldn’t have a clue ..so the next few days I will run my 372xp ..I am thinking on 1 more as I cut pretty steady and now I am leaning towards the 562 mark2 ..any thoughts appreciated ..71 years young and still doing it…cheers and thanks for your channel and the time and effort you put into making videos ..
@stevenlaxton3618
5 ай бұрын
@@dgoodman1484 thanks much appreciated
@dgoodman1484
5 ай бұрын
👍🏼
@kurtsteele5587
5 ай бұрын
How's the Tinman and family
@jakegorman7121
5 ай бұрын
I've never heard of anyone wanting to lower the cutting rpm in a saw...interesting.
Пікірлер: 71