That was just a stall of the right wing. Probably not the lightest plane and that maneuver may have been a bit too aggressive for the speed you were flying at.
@edwardwaldrep7727
3 ай бұрын
Accelerated tip stall. You try to correct and it makes it worse. Some aerobatic planes are worse than others. Good luck on the next print!
@rinku1n1n
20 күн бұрын
That's a shame. I also crashed my 3D aircraft, the WACO YMF-5, the other day. I was flying too fast and the tail blew off. 3D aircraft need to be reinforced in the details. I hope you continue to enjoy great flights.
@GEARHEADFPV
20 күн бұрын
@@rinku1n1n its all part of the hobby. I got plenty other toys to play with. Fly, crash, build, repeat
@thenerdoligist1292
2 ай бұрын
I use 3D printed parts for cowls and canopies mostly in combination with foam board or balsa for strength and stiffness. Carbon fiber tubes for spars works well. Your wing may have flexed too much and caused the stall. Your plane looked cool!
@qwicksilver2
3 ай бұрын
What material did u use to print looks good
@GEARHEADFPV
3 ай бұрын
This was mostly Overture PLA+
@steunsoul
3 ай бұрын
We’re pulling but it wasn’t pulling? Did I understand correct? If so, you pulled to much and the elevator stalled. Only way to recover is to stop pulling and gently pull the plane out of the dive. Hoping you have air enough under the plane.
@GEARHEADFPV
3 ай бұрын
Too much elevator...probably. but more the 3d print failed cause of it. Doesnt matter now...its in the garbage bin. On to the next one!
@JustGoAndFly
3 ай бұрын
crazy take.. go crash a horizon this hard. same thing. the plane is also heavy and outdated.. you said you had an 8-cell battery in there man. it flew like a rock. 3D printing is the future of this hobby. getting better by the day, literally.
@GEARHEADFPV
3 ай бұрын
They are getting better. Ive got quite a few different printed planes. Printers, filaments, and designs are all improving. None of them crash well no matter what they are made of. Just have to keep flying stuff. Crashing is just part of the game
@dommer2162
3 ай бұрын
The Ole lost something. No it was you.
@monchichis333
3 ай бұрын
It's an EDGE 540 plane
@wcarraft
3 ай бұрын
dont like thers plane thin and weak better to get from planeprint thers plane is build whit lwpla and construkted like foam plane and werry light and righid builds
@BullFrog96
3 ай бұрын
That was definitely an accelerated stall. Sucks. It was a beautiful airplane.
@RobR386
2 ай бұрын
That's the problem with 3D printed planes especially if you used PLA to print it, PLA shatters when crashed. I use ABS for planes and multirotors, way stronger and doesn't shatter like PLA 😊
@yatzeegamingop
2 ай бұрын
3d printed planes are just bad. Compared to foam, balsa or even foamboard models they are heavy and insanely brittle. I remember pulling out my ft viggen from dirt for like 10 centimeters deep and it only needed a nose rebuild. For aerobatics just build a balsa model. Yes 3d is cool but an aertobatics plane is not supposed to stall like that, that's the point.
@SomeGuyInSandy
2 ай бұрын
95 degrees isn't good weather for aerobatics, thin air and all.
@sullytrny
3 ай бұрын
nice, bigger motor? good luck
@qwicksilver2
3 ай бұрын
G stall try bit more nose weight
@WestPsyde
3 ай бұрын
"dont think that one is in good shape anymore"
@GEARHEADFPV
3 ай бұрын
It just changed shape....
@R.B_B
3 ай бұрын
What airfoil and angle of incidence you using in the wing?
@GEARHEADFPV
3 ай бұрын
Not really sure. These are pre- designed plans. They dont list alot of the details
Пікірлер: 24